D-Link xStack DES-6500 Cli Manual page 244

xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual
create cpu access_profile
Purpose
Used to create an access profile specifically for CPU Interface Filtering on the
Switch and to define which parts of each incoming frame's header the Switch will
examine. Masks can be entered that will be combined with the values the Switch
finds in the specified frame header fields. Specific values for the rules are entered
using the config cpu access_profile command, below.
Syntax create cpu access_profile profile_id <value 1-5> [ethernet {vlan | source_mac
<macmask> | destination_mac <macmask> | ethernet_type} | ip {vlan |
source_ip_mask <netmask> | destination_ip_mask <netmask> | dscp |
[icmp {type | code} | igmp {type} | tcp {src_port_mask <hex 0x0-0xffff> |
dst_port_mask <hex 0x0-0xffff>} | flag_mask [all | {urg | ack | psh | rst | syn |
fin}]} | udp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} |
protocol_id {user_mask <hex 0x0-0xffffffff>}]} | packet_content_mask {offset 0-
15 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> | offset 16-31 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> | {offset 32-47 <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | {offset 48-63 <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | {offset
64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff>}]
Description
The create cpu access_profile command is used to create an access profile used
only for CPU Interface Filtering. Masks can be entered that will be combined with the
values the Switch finds in the specified frame header fields. Specific values for the
rules are entered using the config cpu access_profile command, below.
profile_id <value 1-5>  Specifies an index number that will identify the access profile
Parameters
being created with this command.
ethernet  Specifies that the Switch will examine the layer 2 part of each packet
header.
vlan  Specifies that the Switch will examine the VLAN part of each packet

header.

source_mac <macmask> - Specifies to examine the source MAC address
mask.

destination_mac <macmask> - Specifies to examine the destination MAC
address mask.
ethernet_type  Specifies that the switch will examine the Ethernet type value

in each frame's header.
ip  Specifies that the switch will examine the IP address in each frame's header.
vlan  Specifies a VLAN mask.

source_ip_mask <netmask>  Specifies an IP address mask for the source IP

address.
destination_ip_mask <netmask>  Specifies an IP address mask for the

destination IP address.
dscp  Specifies that the switch will examine the DiffServ Code Point (DSCP)

field in each frame's header.
icmp  Specifies that the switch will examine the Internet Control Message

Protocol (ICMP) field in each frame's header.


field.
type  Specifies that the switch will examine each frame's ICMP Type field.
code  Specifies that the switch will examine each frame's ICMP Code
240