D-Link DGS-3120-48PC Reference Manual page 96

®
xStack DGS-3120 Series Managed Switch CLI Reference Guide
chunk 1 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 1 mask here.
offset_chunk_2 - (Optional) Specify the value of the packet bytes to be matched. Offset
chunk 2 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 2 mask here.
offset_chunk_3 - (Optional) Specify the value of the packet bytes to be matched. Offset
chunk 3 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 3 mask here.
offset_chunk_4 - (Optional) Specify the value of the packet bytes to be matched. Offset
chunk 4 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 4 mask here.
ipv6 - Specify that the rule applies to IPv6 fields. (EI Mode Only)
class - (Optional) Specify the value of the IPv6 class. (EI Mode Only)
<value 0-255> - Enter the IPv6 class value here. This value must be between 0 and 255.
flowlabel - (Optional) Specify the value of the IPv6 flow label. (EI Mode Only)
<hex 0x0-0xffff> - Enter the IPv6 flow label mask used here.
source_ipv6 - (Optional) Specify the value of the IPv6 source address. (EI Mode Only)
<ipv6addr> - Enter the source IPv6 address used for this configuration here.
mask - (Optional) Specify an additional mask parameter that can be configured. (EI Mode Only)
<ipv6mask> - Enter the source IPv6 mask here.
destination_ipv6 - (Optional) Specify the value of the IPv6 destination address. (EI Mode Only)
<ipv6addr> - Enter the destination IPv6 address used for this configuration here.
mask - (Optional) Specify an additional mask parameter that can be configured. (EI Mode Only)
<ipv6mask> - Enter the destination IPv6 mask here.
tcp - (Optional) Specify to configure the TCP parameters. (EI Mode Only)
src_port - Specify the value of the IPv6 Layer 4 TCP source port.
<value 0-65535> - Enter the TCP source port value here. This value must be between 0
and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the TCP source port mask value here.
dst_port - (Optional) Specify the value of the IPv6 Layer 4 TCP destination port.
<value 0-65535> - Enter the TCP destination port value here. This value must be between
0 and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the TCP destination port mask value here.
udp - (Optional) Specify to configure the UDP parameters. (EI Mode Only)
src_port - Specify the value of the IPv6 Layer 4 UDP source port.
<value 0-65535> - Enter the UDP source port value here. This value must be between 0
and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the UDP source port mask value here.
dst_port - Specify the value of the IPv6 Layer 4 UDP destination port.
<value 0-65535> - Enter the UDP destination port value here. This value must be between
0 and 65535.
mask - Specify an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the UDP destination port mask value here.
icmp - (Optional) Specify to configure the ICMP parameters used. (EI Mode Only)
type - Specify that the rule applies to the value of ICMP type traffic.
<value 0-255> - Enter the ICMP type traffic value here. This value must be between 0 and
255.
code - Specify that the rule applies to the value of ICMP code traffic.
<value 0-255> - Enter the ICMP code traffic value here. This value must be between 0 and
255.
port - Specify the port list used for this configuration.
<portlist> - Enter a list of ports used for the configuration here.
all - Specify that all the ports will be used for this configuration.
vlan_based - Specify that the rule will be VLAN based.
vlan - Specify the VLAN name used for this configuration.
<vlan_name> - Enter the VLAN name used for this configuration here.
92