Eaton PowerXL DM1 Series Applications Manual page 226
Hide thumbs
Also See for PowerXL DM1 Series:
- Installation manual (102 pages) ,
- Quick start manual (68 pages) ,
- Instruction leaflet (31 pages)
Table of Contents
Advertisement
Chapter 7- Multi-purpose application
Table 68. Fieldbus (FB) status (Cont.).
FB process data input 8 selection
P10.1.8
b
Minimum value:
0
Description:
With the fieldbus data output selections, parameter/monitor IDs can be assigned to these registers and then read over the desired
fieldbus network word for process data. Any drive parameter with an ID can be read over these values.
Default values for process data in:
Process data IN1 = NULL = ID 0;
Process data IN2 = FB PI Set Point1= ID 2542;
Process data IN3 = FB PI Feedback1= ID 2550;
Process data IN4 = Acceleration time 1= ID 103;
Process data IN5 = Deceleration time 1= ID 104;
Process data IN6 = Current limit= ID 107;
Process data IN7 = NULL= ID 0; or
Process data IN8 = NULL= ID 0.
P10.2 - FB process data
output selection.
FB process data output 1 selection
P10.2.1
b
Minimum value:
N.A.
Description:
With the fieldbus data output selections, parameter/monitor IDs can be assigned to these registers and then read over the desired
fieldbus network word for process data. Any drive parameter with an ID can be read over these values.
Default values for process data out in fieldbus (build table for below values):
Process data Out1 = Output frequency = ID 1;
Process data Out2 = Motor speed = ID 2;
Process data Out3 = Motor current = ID 3;
Process data Out4 = Motor torque = ID 4;
Process data Out5 = Motor power = ID 5;
Process data Out6 = Motor voltage = ID 6;
Process data Out7 = DC link voltage = ID 7; or
Process data Out8 = Latest fault code = ID 28.
FB process data output 2 selection
P10.2.2
b
Minimum value:
N.A.
With the fieldbus data output selections, parameter/monitor IDs can be assigned to these registers and then read over the desired
Description:
fieldbus network word for process data. Any drive parameter with an ID can be read over these values.
Default values for process data out in fieldbus (build table for below values):
Process data Out1 = Output frequency = ID 1;
Process data Out2 = Motor speed = ID 2;
Process data Out3 = Motor current = ID 3;
Process data Out4 = Motor torque = ID 4;
Process data Out5 = Motor power = ID 5;
Process data Out6 = Motor voltage = ID 6;
Process data Out7 = DC link voltage = ID 7; or
Process data Out8 = Latest fault code = ID 28.
FB process data output 3 selection
P10.2.3
b
Minimum value:
N.A.
With the fieldbus data output selections, parameter/monitor IDs can be assigned to these registers and then read over the desired
Description:
fieldbus network word for process data. Any drive parameter with an ID can be read over these values.
Default values for process data out in fieldbus (build table for below values):
Process data Out1 = Output frequency = ID 1;
Process data Out2 = Motor speed = ID 2;
Process data Out3 = Motor current = ID 3;
Process data Out4 = Motor torque = ID 4;
Process data Out5 = Motor power = ID 5;
Process data Out6 = Motor voltage = ID 6;
Process data Out7 = DC link voltage = ID 7; or
Process data Out8 = Latest fault code = ID 28.
216
POWERXL DM1 SERIES VARIABLE FREQUENCY DRIVES MN040049EN—September 2021 www.eaton.com
Maximum value:
12,464
Maximum value:
N.A.
Maximum value:
N.A.
Maximum value:
N.A.
ID 2540
Default value:
0
ID 1556
Default value:
1
ID 1557
Default value:
2
ID 1558
Default value:
3
Advertisement
Table of Contents
