Intermec Janus 2020 User Manual page 563

Longitudinal Redundancy Check, See LRC command
long-range laser scanner
safety information, 2-46
spotting beam, 2-46
using, 2-46
lowercase letters, bar code labels to scan, C-21
LRC command, 12-72
LUPGRADE, FTA command, 6-51
M
MAKE_USA, D-15
MAKELANG, D-15
MAKENEW, 3-20, D-16
managing power, See power management
manual
list for reference, xxviii
where to find information, xxiii
Manual Viewport Movement mode
configuring, 12-100
using, 2-25
MCFORMAT.EXE, using flash cards, 4-16, 4-18
memory
application flash, described, A-18
conventional, described, A-16
drive specifications, A-4
expanded, described, A-17
extended, 3-31, A-16, A-17
high memory area, described, A-17
insufficient to run applications, 10-6, 10-15, 10-24
making available on the reader, 3-35 to 3-39
map, illustrated, A-15
overlapping ranges, EMM386, 10-20
RAM drives, using, 3-31
rolled-over, described, A-16
storing data, recommended uses, 2-44
types used on reader, A-15 to A-18
upper memory block, described, A-16
user flash, described, A-18
memory card
illustrated, 4-4
reader accessory, 1-4
types recommended, 4-5
menu, MCFORMAT, 4-16
messages
Bad BIOS Checksum, 9-15, 9-16, 10-5
Bad command or filename, 10-6, 10-17, 10-26
Bad Saved State, 10-5
conventions for manual, xxvi
File not found, 10-6, 10-31
Invalid media type reading drive X, 10-17
Not ready reading drive X, 10-6, 10-17, 10-31
Write Fault Error Writing Device PRN, 10-20
XX Keyboard Error, 10-4
mixed-full ASCII, Code 39, 12-21
MkImage
defined, 3-4
drive C, adding, editing, deleting files, 3-23
drive C, learning how to change, 3-10 to 3-12
examples of using, 3-26 to 3-29
image file, creating a drive C, 3-24
mode, Suspend, 6-20, 7-17
models, for the reader, 1-5
modem card
illustrated, 4-4
reader accessory, 1-4
modifiers, using on international keypads, 8-12
Monochrome Video mode, 12-48
moving the viewport
cursor to viewport, 11-20
down, 11-15
learning how to, 2-25
left, 11-16
lower right corner, 11-17
page down, 11-18
page up, 11-19
reader commands, using, 11-15 to 11-20
right, 11-17
to the cursor, 11-19
up, 11-16
upper right corner, 11-18
MS-DOS, See DOS
MS-Flash
formatting flash cards, 4-15, 4-18
See also flash card
MSI command, 12-72
MTAA.EXE, 10-18
MTAB.EXE, 10-18
Multi-Drop protocol
address, configuring, 12-7
baud rate, configuring, 12-10
defined, 6-10
parameters, list of, 6-14, 12-38
troubleshooting, 10-13
User-Defined, configuring, 12-39
User-Defined, POL and SEL combinations, C-7
Multiple-Read labels, defined, 12-34
N
National Language Support, See DOS NLS
NEG command, 12-74
Negative Acknowledge, See NEG command
network port, communications dock, 12-35
networking
application, choosing, 6-10
BFT, downloading applications, 6-42 to 6-53
COM port, selecting, 6-13, 12-36
Communications Manager, using, 6-37 to 6-42
configuring the reader, 6-13
I
Index
I-15