Suzuki XL7 2007 Service Manual page 1988

8A-2 Seat Belts:
• When the passenger seat belt is buckled with an
occupant sitting in the passenger front seat, and the
ignition switch is turned ON, the following events will
occur:
– The tone alarm will not operate.
– The reminder lamp, which is located within the PPS
status indicator for the passenger seat, will not be
turned ON.
• When the driver seat belt is not buckled, the driver
door is closed, and the ignition switch is in the ON
position, the following events will occur:
– The tone alarm will operate for 4-8 seconds and
then go OFF.
– The fasten safety belt indicator will turn ON solid for
20 seconds, then flash for 55 seconds before
turning OFF. The indicator will immediately turn
OFF if the driver seat belt is buckled.
• When the passenger seat belt is not buckled with an
occupant sitting in the passenger front seat, and the
ignition switch is turned ON for approximately 25
seconds, the following events will occur:
– The tone alarm will operate for 4-8 seconds and
then go OFF.
– The reminder lamp, which is located within the PPS
status indicator for the passenger seat, will be
turned ON solid for 20 seconds, then flash for 55
seconds before turning OFF. The indicator will
immediately turn OFF if the passenger seat belt is
buckled.
Rear Seat Belt System
The Rear Seat Belt System includes the following
components:
• The rear seat belt retractor is located at the
wheelhouse panel and attached to the floor panel by
the rear seat shoulder belt retractor bracket.
• The rear seat belt buckles and the center seat belt
buckle are attached to each seat.
Child Seat Restraint System
WARNING
!
A child in a rear-facing child restraint can be
seriously injured if the right-front passengers
air bag inflates. This is because the back of a
rear-facing child restraint would be very
close to the inflating air bag. NEVER use a
rear-facing child restraint in this vehicle. If a
forward-facing child restraint is suitable for
your child, ALWAYS move the front
passenger seat as far back as it will go and
then install the child restraint. Be sure the
Schematic and Routing Diagram
child restraint position does not conflict with
any additional requirements provided by the
manufacturer. For more information, refer to
the vehicle owners manual and the
instruction that came with the child restraint.
The child seat may only be used in a forward facing
seating location. The child seat should be installed and
secured according to the manufacturer's directions. If the
child seat has a top strap, the seat will need to be
anchored. Passengers should not be allowed to sit at
locations where the seat belts are being used to secure
the child seat.
All vehicles are equipped with a dual-mode type retractor
with emergency and automatic locking features. The
automatic locking feature is for restraint of a child seat.
The child seat can be secured by pulling the seat belt all
the way out to lock it. Then tighten the seat belt around
the child seat.
If a child seat is to be used in the second seat position, a
special dealer-installed anchor must be used in order to
anchor the child seat top strap. This only applies to the
seats designed with the top strap provision and for the
vehicles sold in Canada. In order to ensure the correct
top strap angle, the child seat is only to be used at the
seating position for which the top strap anchor is
installed.
Fasten Safety Belt Indicators
There are 2 fasten safety belt indicators for this vehicle.
The driver fasten safety belt reminder is monitored on
the instrument panel cluster (IPC) and the passenger
fasten safety belt reminder is located in the
PASSENGER AIR BAG ON/OFF status indicator. The
fasten safety belt indicator may only be ON during RUN.
The IPC illuminates the fasten safety belt indicator under
the following condition:
The inflatable restraint sensing and diagnostic module
(SDM) controls both indicators by using the serial data
message communications. If either seat belt is
unfastened, (passenger indicator will only illuminate if an
occupant is seated in the front passenger seat and the
key has been in RUN for approximately 25 seconds), the
SDM will illuminate the appropriate fasten safety belt
indicator for 20 seconds of solid illumination and then 55
seconds of flashing illumination before turning OFF or
immediately turn OFF when the seat belt is fastened. If
the driver seat belt is unfastened within 8 seconds
following a key transition to RUN the SDM sends a
message requesting 5 chimes to sound. When the
enhanced reminder function is enabled the illumination
and chime sequence will repeat after approximately 30
seconds and then again after 3 minutes if the seat belt
remains unfastened and vehicle speed is greater than 5
MPH.