Suzuki XL7 2007 Service Manual page 2232

9A-124 Wiring Systems:
Name
C901 (6 cavities)
C906 (4 cavities)
G101
G103
G105
G107
G108
G109
G201
G203
G205
G301
G311
G401
G403
S100
S101
S102
S103
S104
S105
S106
S107
S108
S109
Location
Body harness to the liftgate harness, at
the top left corner of the liftgate
Licence lamp harness to the liftgate
harness, in the middle of the lifgate by
the licence plate
At the LF corner of the vehicle, below the
headlamp, mounted on the frame rail
In the left front of the engine
compartment, behind the windshield
washer fluid pump
On the lower left front side of the engine
On the upper left front side of the engine
On the Upper right rear side of the
engine
On the upper left rear side of the engine
At the RF corner of the passenger
compartment, behind the RF kick panel
At the lower center of the I/P, attached to
the upper front side of the I/P fuse block
At the lower left corner of the I/P, behind
the kick panel
Beneath the LF seat, under the carpet
Beneath the RF seat, under the carpet
At the LR corner of the passenger
compartment, behind the LR trim panel
At the RR corner of the vehicle, under the
RR trim panel
In the engine harness, approximately 5
cm (1.96 in) from the G107 breakout
In the fuel injector harness, before the
fuel injector 1 breakout.
In the right front headlamp harness
before the park lamp breakout
In the left front headlamp harness before
the park lamp breakout
In the fuel injector harness, before the
fuel injector 2 breakout
In the engine harness, approximately 5
cm (1.96 in) from the C105 breakout
In the engine harness, approximately 8
cm (3.15 in) from the Ignition Coil 3
breakout
In the engine harness, approximately 9
cm (3.54 in) from the C105 breakout
In the engine harness, approximately 7.5
cm (2.95 in) from the Heated Oxygen
Sensor (HO2S) Bank 2 Sensor 1
breakout toward the C105 breakout
In the engine harness, approximately 7.5
cm (2.95 in) from the Heated Oxygen
Sensor (HO2S) Bank 2 Sensor 1
breakout toward the Mass Air Flow
(MAF)/Intake Air Temperature (IAT)
Sensor breakout
Locator View
"Harness Routing
Views"
"Harness Routing
Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Power and Grounding
Component Views"
"Harness Routing
Views"
"Harness Routing
Views"
—
—
"Harness Routing
Views"
"Harness Routing
Views"
"Harness Routing
Views"
"Harness Routing
Views"
"Harness Routing
Views"
"Harness Routing
Views"
Connector End View
"Inline Harness
Connector End Views"
"Inline Harness
Connector End Views"
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—