Suzuki XL7 2007 Service Manual page 2061

Repair Instructions
Perform the "Diagnostic Repair Verification - Vehicle
Diagnostic Information: " after completing the diagnostic
procedure.
• "Inflatable Restraint Sensing and Diagnostic Module
Replacement"
• "Inflatable Restraint Passenger Presence System
Replacement - Front" for PPS module replacement,
setup, and programming
Repairs and Inspections Required After a
Collision
Accident With or Without Air Bag Deployment -
Component Inspections
WARNING
!
Proper operation of the SIR sensing system
requires that any repairs to the vehicle
structure return the vehicle structure to the
original production configuration. Not
properly repairing the vehicle structure could
cause non-deployment in a collision or
deployment for conditions less severe than
intended.
After a collision, inspect the following components as
indicated. If any damage is detected, replace the
component. If damage to the mounting points or
mounting hardware is detected, repair the component or
replace the hardware as needed.
• Steering column—Perform the steering column
accident damage checking procedures. Refer to
"Steering Column Accident Damage Inspection: ".
• Instrument panel (I/P) knee bolsters and mounting
points—Inspect the knee bolsters for bending,
twisting, buckling, or any other type of damage.
• I/P brackets, braces, etc.—Inspect for bending,
twisting, buckling, or any other type of damage.
• Seat belts—Perform the seat belt operational and
functional checks. Refer to "Operational and
Functional Checks: ".
• Seats and seat mounting points—Inspect for bending,
twisting, buckling, or any other type of damage.
• Passenger seat bottom equipped with Passenger
Presence System (PPS)—Check for any DTCs or
problems that may cause the PPS not to function
properly.
Accident With Frontal Deployment - Component
Replacement and Inspections
After a collision involving air bag deployment, replace
the following components.
NOTE
The front passenger seat is equipped with a
PPS, which detects an occupant. If the
requirements for disabling the I/P air bag are
met then the PPS will communicate with the
SDM to disable/turn off the I/P air bag, even in
a accident. For more information on the PPS
refer to "SIR System Description and
Operation".
• Inflatable restraint I/P module, if deployed and after
performing the necessary inspections listed above.
• Inflatable restraint steering wheel module
• Inflatable restraint SDM
• Inflatable restraint front end sensors
• Inflatable restraint seat belt retractor pretensioners
Perform additional inspections on the following
components.
• Steering wheel module coil and the coil wiring
pigtail—Inspect for melting, scorching, or other
damage due to excessive heat.
• Mounting points or mounting hardware for the I/P
module, steering wheel module, SDM, and
pretensioners—Inspect for any damage and repair or
replace each component as needed.
Accident With Side Air Bag Deployment -
Component Replacement and Inspections
After a collision involving side air bag deployment,
replace the following components.
• Inflatable restraint side impact sensors (SIS), on the
side of the impact
• Inflatable restraint roof rail module, on the side of the
impact
• Inflatable restraint side impact module, on the side of
the impact
• Inflatable restraint SDM
• Inflatable restraint seat belt retractor pretensioners
Perform additional inspections on the following
components.
• Mounting points or mounting hardware for the SIS—
Inspect for any damage and repair or replace each
component as needed.
• Mounting points or mounting hardware for the roof rail
module on the side of impact—Inspect for any
damage and repair or replace each component as
needed.
• Mounting points or mounting hardware for the side
impact module on the side of impact—Inspect for any
damage and repair or replace each component as
needed.
• Mounting points or mounting hardware for the SDM
and seat belt retractor pretensioners—Inspect for any
damage and repair or replace each component as
needed.
Air Bag System: 8B-49