Nokia 7302 Manual

Nokia 7302 Manual

Intelligent services access manager/fttn/fx, fd 100/320gbps nt and fx nt ihub services
Hide thumbs Also See for 7302:
Table of Contents

Advertisement

FD 100/320Gbps NT and FX NT IHub Services Guide
7302 Intelligent Services Access Manager
7330 Intelligent Services Access Manager FTTN
7360 Intelligent Services Access Manager FX
Release 5.6.01
FD 100/320Gbps NT and FX NT IHub Services
Guide
3HH-11985-AAAA-TQZZA
Issue: 13
June 2017
Nokia — Proprietary and confidential
Use pursuant to applicable agreements

Advertisement

Table of Contents
loading

Summary of Contents for Nokia 7302

  • Page 1 FD 100/320Gbps NT and FX NT IHub Services Guide 7302 Intelligent Services Access Manager 7330 Intelligent Services Access Manager FTTN 7360 Intelligent Services Access Manager FX Release 5.6.01 FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13 June 2017 Nokia —...
  • Page 2 © 2014-2017 Nokia. Contains proprietary/trade secret information which is the property of Nokia and must not be made available to, or copied or used by anyone outside Nokia without its written authorization. Not to be used or disclosed except in accordance with applicable agreements.
  • Page 3: Table Of Contents

    FD 100/320Gbps NT and FX NT IHub Services Guide Table of contents Preface...................41 Scope ......................41 Audience....................41 Required knowledge..................41 Product naming ..................41 Documents ....................41 Acronyms and initialisms ................41 Safety information..................42 Special information ..................42 Release notes....................42 Getting Started ................43 In This Document ..................43 Services Command Reference..............43 CLI Command Syntax Symbols..............44 Services Overview ................45...
  • Page 4 FD 100/320Gbps NT and FX NT IHub Services Guide 3.8.4.4 Deleting SDPs ...................58 3.8.4.5 Modifying LSPs..................58 3.8.4.6 Deleting LSPs....................59 Basic Configuration ...................59 3.10 Ethernet Connectivity Fault Management ..........60 3.10.1 Configuring ETH-CFM with CLI ..............63 3.10.1.1 Create a Maintenance Domain..............63 3.10.1.2 Create a Maintenance Association............63 3.11 G.8032 Ethernet Ring Protection Switching ..........64...
  • Page 5 FD 100/320Gbps NT and FX NT IHub Services Guide 3.17.4.1 eth-cfm.......................86 3.17.4.2 domain.......................87 3.17.4.3 association....................88 3.17.4.4 bridge-identifier..................88 3.17.4.5 mhf-creation....................89 3.17.4.6 ccm-interval ....................89 3.17.4.7 remote-mepid ....................90 3.17.4.8 inactivity-timer....................90 3.17.4.9 y1731pm....................91 3.17.4.10 shutdown ....................91 3.17.4.11 priority......................91 3.17.4.12 period......................92 3.17.4.13 data-size ....................92 3.17.4.14 measurement-period .................93 3.17.4.15 mac-address....................93...
  • Page 6 FD 100/320Gbps NT and FX NT IHub Services Guide 4.4.1 Common Configuration Tasks ..............112 4.4.2 Creating an Epipe Service...............112 4.4.2.1 Configure Epipe QoS Attributes ..............112 4.4.2.2 Configure Epipe Service MTU Attribute...........113 4.4.2.3 Configuring Epipe SAP Parameters ............113 4.4.2.4 Configuring SDP Bindings ...............115 4.4.3 Configuring Management Points (MEPs/MIPs) for Ethernet CFM on SDP bindings...................118...
  • Page 7 FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.5.11 mep......................138 4.6.5.12 ccm-enable ....................139 4.6.5.13 ccm-ltm-priority ..................139 4.6.5.14 low-priority-defect ..................140 4.6.5.15 mac-address....................140 4.6.5.16 mip......................141 4.6.5.17 vlan-dot-1q-etype..................141 4.6.6 Show Commands ..................142 4.6.6.1 egress-label .....................142 4.6.6.2 ingress-label ....................143 4.6.6.3 sap-using ....................144 4.6.6.4 sdp......................145 4.6.6.5 sdp-using ....................146...
  • Page 8 FD 100/320Gbps NT and FX NT IHub Services Guide 5.4.6 VPLS IGMP Snooping (s,g) Flooding List ..........175 5.4.7 VPLS and Spanning Tree Protocol............175 5.4.7.1 Spanning Tree Operating Modes ............176 5.4.7.2 Multiple Spanning Tree................177 5.4.7.3 Redundancy Access to VPLS..............177 5.4.7.4 MSTP General Principles ................178 5.4.7.5 MSTP implementation ................178 5.4.7.6...
  • Page 9 FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.6.3 Operationally Learning ................213 5.8.6.4 Operationally Forwarding ................213 5.8.7 Configuring SDP Bindings ...............214 Service Management Tasks ..............217 5.9.1 Modifying VPLS Service and SAP Parameters ........217 5.9.2 Enabling and Disabling VPLS Entities.............218 5.9.3 Deleting a VPLS Service or SAP.............219 5.9.4...
  • Page 10 FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.7 ignore-standby-signaling .................255 5.16.2.8 revert-time ....................255 5.16.2.9 static-mac ....................256 5.16.2.10 suppress-standby-signaling..............256 5.16.2.11 extfwd ......................257 5.16.2.12 device-ip ....................257 5.16.2.13 fdb-table-size ...................257 5.16.2.14 interface....................258 5.16.2.15 address....................259 5.16.2.16 arp-timeout ....................260 5.16.2.17 local-age ....................260 5.16.2.18 mesh-sdp....................261 5.16.2.19 spoke-sdp ....................262...
  • Page 11 FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.56 split-horizon-group...................283 5.16.2.57 vc-type .....................283 5.16.3 VPLS STP Commands ................284 5.16.3.1 stp......................284 5.16.3.2 auto-edge ....................284 5.16.3.3 edge-port ....................284 5.16.3.4 forward-delay...................285 5.16.3.5 hello-time ....................286 5.16.3.6 hold-count....................286 5.16.3.7 link-type ....................287 5.16.3.8 mst-instance ....................287 5.16.3.9 mst-path-cost...................287 5.16.3.10...
  • Page 12 FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.5.10 qos......................306 5.16.5.11 rate-limit....................307 5.16.5.12 rate-limit....................307 5.16.5.13 rate-limit-pbits ..................308 5.16.5.14 rate-limit....................308 5.16.5.15 dot1p......................309 5.16.5.16 meter-mode .....................310 5.16.6 VPLS Multicast commands..............310 5.16.6.1 igmp-snooping ..................310 5.16.6.2 fast-leave ....................310 5.16.6.3 last-member-query-interval..............311 5.16.6.4 mrouter-port.....................311 5.16.6.5 query-interval...................312 5.16.6.6 query-response-interval................313...
  • Page 13 FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.9.6 mesh-sdp....................344 5.16.9.7 spoke-sdp ....................344 5.16.9.8 stp......................345 5.16.9.9 detected-protocols ...................345 5.16.9.10 statistics....................346 5.16.9.11 mesh-sdp....................347 5.16.9.12 spoke-sdp ....................348 5.16.9.13 querier .....................348 5.16.10 Debug Commands...................349 5.16.10.1 id......................349 5.16.10.2 igmp-snooping ..................349 5.16.10.3 detail-level ....................349 5.16.10.4 mac......................350 5.16.10.5...
  • Page 14 FD 100/320Gbps NT and FX NT IHub Services Guide 6.9.1.1 Global Commands...................363 6.9.1.2 Interface Commands ................363 6.9.1.3 Interface SAP Commands ...............365 6.9.1.4 Show Commands ..................365 6.9.1.5 Clear Commands..................365 6.10 IES Service CLI Configuration Commands ..........366 6.10.1 Generic Commands.................366 6.10.1.1 shutdown ....................366 6.10.1.2 description ....................367 6.10.1.3...
  • Page 15 FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.7.6 option.......................388 6.10.7.7 interface-id....................389 6.10.7.8 remote-id ....................389 6.10.7.9 server.......................390 6.10.7.10 source-address..................390 6.10.7.11 icmp6 .......................390 6.10.7.12 packet-too-big..................391 6.10.7.13 param-problem ..................391 6.10.7.14 time-exceeded ..................392 6.10.7.15 unreachables ...................392 6.10.7.16 local-proxy-nd ..................393 6.10.7.17 prefix-stability...................394 6.10.7.18 prfx-hlddwn-time ..................394 6.10.8 IES SAP Filter and QoS Policy Commands ..........395...
  • Page 16 FD 100/320Gbps NT and FX NT IHub Services Guide 7.3.2 ISAM to PE Routing Protocols..............424 Configuring a VPRN Service with CLI .............424 Basic Configuration .................425 Common Configuration Tasks ..............426 Configuring VPRN Components..............427 7.7.1 Creating a VPRN Service ................427 7.7.2 Configuring Global VPRN Parameters ............427 7.7.3 Configuring Router Interfaces..............428 7.7.4...
  • Page 17 FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.2.13 mtu......................457 7.10.2.14 other-stateful-configuration..............457 7.10.2.15 prefix......................457 7.10.2.16 autonomous.....................458 7.10.2.17 on-link ......................458 7.10.2.18 preferred-lifetime ..................459 7.10.2.19 valid-lifetime.....................459 7.10.2.20 reachable-time..................460 7.10.2.21 retransmit-time..................460 7.10.2.22 router-lifetime...................460 7.10.2.23 route-distinguisher ...................461 7.10.2.24 router-id ....................461 7.10.2.25 sgt-qos.....................462 7.10.2.26 qos......................462 7.10.2.27 rate-limit....................463...
  • Page 18 FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.6.7 remote-id ....................485 7.10.6.8 prefix-stability...................485 7.10.6.9 prfx-hlddwn-time ..................486 7.10.6.10 server.......................486 7.10.6.11 source-address..................487 7.10.6.12 icmp6 .......................487 7.10.6.13 packet-too-big..................487 7.10.6.14 param-problem ..................488 7.10.6.15 time-exceeded ..................489 7.10.6.16 unreachables ...................489 7.10.6.17 local-proxy-nd ..................490 7.10.7 SAP Commands ..................490 7.10.7.1 sap......................490 7.10.8...
  • Page 19 FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.9.21 ibgp-multipath ..................509 7.10.9.22 import.......................509 7.10.9.23 keepalive ....................510 7.10.9.24 local-address ...................510 7.10.9.25 local-as ....................511 7.10.9.26 local-preference..................512 7.10.9.27 loop-detect....................513 7.10.9.28 med-out ....................514 7.10.9.29 min-as-origination ..................515 7.10.9.30 min-route-advertisement................515 7.10.9.31 multihop ....................516 7.10.9.32 multipath ....................516 7.10.9.33 next-hop-self....................517 7.10.9.34...
  • Page 20 FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.10.29 external-preference .................536 7.10.10.30 overload....................537 7.10.10.31 overload-include-stub ................538 7.10.10.32 overload-on-boot ..................538 7.10.10.33 preference ....................539 7.10.10.34 reference-bandwidth................540 7.10.10.35 timers.......................541 7.10.10.36 lsa-arrival ....................541 7.10.10.37 lsa-generate.....................542 7.10.10.38 spf-wait ....................542 7.10.11 RIP Commands ..................543 7.10.11.1 rip......................543 7.10.11.2 authentication-key ...................543...
  • Page 21 FD 100/320Gbps NT and FX NT IHub Services Guide 7.10.12.22 neighbor....................578 7.10.12.23 paths......................582 7.10.12.24 routes.......................583 7.10.12.25 summary....................586 7.10.12.26 interface....................587 7.10.12.27 dhcp6.......................590 7.10.12.28 statistics....................590 7.10.12.29 summary....................591 7.10.12.30 routes.......................591 7.10.12.31 neighbour....................592 7.10.12.32 rip......................593 7.10.12.33 database....................593 7.10.12.34 neighbor....................594 7.10.12.35 peer ......................596 7.10.12.36 statistics....................597 7.10.12.37 route-table ....................599 7.10.12.38...
  • Page 22 FD 100/320Gbps NT and FX NT IHub Services Guide Mirror Service CLI Configuration Commands..........616 8.7.1 Generic Commands.................616 8.7.1.1 description ....................616 8.7.1.2 shutdown ....................617 8.7.2 Mirror Configuration Commands .............618 8.7.2.1 mirror-dest ....................618 8.7.2.2 sap......................619 8.7.3 Debug Configuration Commands ............621 8.7.3.1 mirror-source ...................621 8.7.3.2 port ......................621 8.7.3.3...
  • Page 23 FD 100/320Gbps NT and FX NT IHub Services Guide List of figures Services Overview ................45 Figure 1 Service Entities..................48 Figure 2 Service Access Point (SAP) ..............49 Figure 3 SDP ......................50 Figure 4 Service Creation and Implementation Flow..........52 Figure 5 Ring in the initial state ................65 Figure 6 Ring in the protection state................66 Figure 7...
  • Page 24 FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13...
  • Page 25 FD 100/320Gbps NT and FX NT IHub Services Guide List of tables Getting Started ................43 Table 1 Configuration Process ................43 Table 2 Command Syntax Symbols ...............44 Services Overview ................45 Table 3 Acronym callout ..................61 Table 4 description command ................79 Table 5 description command ................79 Table 6 customer command ...................80...
  • Page 26 FD 100/320Gbps NT and FX NT IHub Services Guide Table 44 Show Service Service-using Command Output Fields......99 Table 45 sdp command ..................100 Table 46 Show Service SDP Command Output Fields ..........101 Table 47 sdp-using command ................102 Table 48 Show Service SDP-using Command Output Fields ........102 Table 49 eth-ring command..................102 Table 50...
  • Page 27 FD 100/320Gbps NT and FX NT IHub Services Guide Table 92 sdp-using command ................146 Table 93 Show Service sdp-using Output Fields............147 Table 94 id command .....................147 Table 95 all command ....................148 Table 96 Show Service-ID All Output Fields ............148 Table 97 base command ..................151 Table 98 Show Service-ID Base Output Fields ............151...
  • Page 28 FD 100/320Gbps NT and FX NT IHub Services Guide Table 140 arp-timeout command................260 Table 141 local-age command .................260 Table 142 mesh-dsp command ................261 Table 143 spoke-sdp command ................262 Table 144 control-word command ................264 Table 145 hash-label command ................264 Table 146 egress command ..................265 Table 147 ingress command ..................265...
  • Page 29 FD 100/320Gbps NT and FX NT IHub Services Guide Table 189 link-type command ..................287 Table 190 mst-instance command ................287 Table 191 mst-path-cost command ................287 Table 192 mst-port-priority command...............288 Table 193 max-age command..................288 Table 194 mode command..................289 Table 195 mst-instance command ................289 Table 196 mst-priority command ................290 Table 197...
  • Page 30 FD 100/320Gbps NT and FX NT IHub Services Guide Table 238 mrouter-port command ................311 Table 239 query-interval command ................312 Table 240 query-response-interval command ............313 Table 241 query-src-ip command................313 Table 242 report-src-ip command ................314 Table 243 robust-count command................314 Table 244 send-queries command ................315 Table 245 static command ..................315 Table 246...
  • Page 31 FD 100/320Gbps NT and FX NT IHub Services Guide Table 287 id command .....................340 Table 288 statistics command ..................340 Table 289 fdb command...................341 Table 290 sap command ..................343 Table 291 counters command ..................343 Table 292 mesh-sdp command ................344 Table 293 spoke-sdp command ................344 Table 294 stp command ...................345...
  • Page 32 FD 100/320Gbps NT and FX NT IHub Services Guide Table 335 ip-mtu command..................376 Table 336 local-proxy-arp command ................377 Table 337 loopback command .................377 Table 338 protect command..................378 Table 339 secondary command ................378 Table 340 dhcp command ..................380 Table 341 gi-address command ................380 Table 342 lease-query command ................381 Table 343...
  • Page 33 FD 100/320Gbps NT and FX NT IHub Services Guide Table 384 base command ..................405 Table 385 dhcp command ..................405 Table 386 statistics command ..................405 Table 387 lease-state command ................406 Table 388 summary command .................408 Table 389 Show DHCP Summary Output ..............408 Table 390 dhcp6 command ..................408 Table 391...
  • Page 34 FD 100/320Gbps NT and FX NT IHub Services Guide Table 432 router-lifetime command................460 Table 433 route-distinguisher command ..............461 Table 434 router-id command ..................461 Table 435 sgt-qos command ..................462 Table 436 qos command ..................462 Table 437 rate-limit command ..................463 Table 438 rate-limit command ..................464 Table 439 static-route command ................465...
  • Page 35 FD 100/320Gbps NT and FX NT IHub Services Guide Table 481 local-proxy-nd command .................490 Table 482 sap command ..................490 Table 483 egress command ..................492 Table 484 egress command ..................492 Table 485 ingress command ..................492 Table 486 ingress command ..................493 Table 487 filter command ..................493 Table 488 filter command ..................494...
  • Page 36 FD 100/320Gbps NT and FX NT IHub Services Guide Table 530 next-hop-self command ................517 Table 531 passive command..................518 Table 532 peer-as command..................518 Table 533 preference command................519 Table 534 prefix-limit command ................519 Table 535 rapid-withdrawal command..............520 Table 536 remove-private command................520 Table 537 type command ..................521 Table 538 ospf command ..................521...
  • Page 37 FD 100/320Gbps NT and FX NT IHub Services Guide Table 579 authentication-key command..............543 Table 580 authentication-type command ..............544 Table 581 check-zero command ................545 Table 582 split-horizon command ................545 Table 583 export command..................546 Table 584 import command..................546 Table 585 message-size command................547 Table 586 metric-in command ..................547 Table 587...
  • Page 38 FD 100/320Gbps NT and FX NT IHub Services Guide Table 628 auth-keychain command .................574 Table 629 damping command ..................574 Table 630 Show BPG Damping Output..............575 Table 631 group command..................576 Table 632 Show Group Output.................577 Table 633 neighbor command..................578 Table 634 Show BPG Neighbor Output..............579 Table 635 Show Advertised and Received Route Output ........582...
  • Page 39 FD 100/320Gbps NT and FX NT IHub Services Guide Table 677 damping command ..................605 Table 678 flap-statistics command ................605 Table 679 neighbor command..................606 Table 680 protocol command ...................606 Table 681 database command .................607 Table 682 statistics command ..................607 Table 683 router-advertisement command...............607 Table 684 id command .....................608...
  • Page 40 FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13...
  • Page 41: Preface

    Readers must be familiar with general telecommunications principles. 1.4 Product naming When the term “ISAM” is used alone, then the 7302 ISAM, the 7330 ISAM FTTN and the 7360 ISAM FX are meant. If a feature is valid for only one of the products, the applicability will be explicitly stated.
  • Page 42: 1.7 Safety Information

    Preface FD 100/320Gbps NT and FX NT IHub Services Guide 1.7 Safety information For safety information, see the Safety Manual for your product. 1.8 Special information The following are examples of how special information is presented in this document. Danger indicates that the described activity or Danger —...
  • Page 43: Getting Started

    FD 100/320Gbps NT and FX NT IHub Services Guide Getting Started 2 Getting Started 2.1 In This Document 2.2 Services Command Reference 2.3 CLI Command Syntax Symbols 2.1 In This Document This document provides process flow information to configure provision services. Table lists the tasks necessary to configure services.
  • Page 44: 2.3 Cli Command Syntax Symbols

    Getting Started FD 100/320Gbps NT and FX NT IHub Services Guide • Service Configuration Commands • VLL Services CLI Command Reference • VPLS Service CLI Command Reference • IES Services CLI Command Reference • VPRN Services CLI Command Reference • Mirror Service CLI Command Reference 2.3 CLI Command Syntax Symbols This section explains the symbols used throughout this manual within a CLI...
  • Page 45: Services Overview

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3 Services Overview 3.1 In this Chapter 3.2 Introduction 3.3 ISAM Service Model 3.4 Service Entities 3.5 Service Creation Process Overview 3.6 Deploying and Provisioning Services 3.7 Configuration Notes 3.8 Configuring Global Service Entities with CLI 3.9 Basic Configuration 3.10 Ethernet Connectivity Fault Management...
  • Page 46: 3.2 Introduction

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3.2 Introduction A service is a globally unique entity that refers to a type of connectivity service for either Internet or VPN connectivity. Each service is uniquely identified by a service ID within a service area.
  • Page 47: Service Policies

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.2.2 Service Policies Common to all ISAM connectivity services are filter policies that are assigned to the service. Filter policies are defined at a global level and then applied to a service on the router.
  • Page 48: 3.4 Service Entities

    Each subscriber service type is configured with at least one service access point (SAP). A SAP identifies the interface point for a service on an Nokia ISAM router (Figure 2). The SAP configuration requires that slot information be specified. The slot parameters must be configured prior to provisioning a service (see the “Port...
  • Page 49: Sap Configuration Considerations

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Figure 2 Service Access Point (SAP) Customer Cust-27 3/1/6 dot1q IP Network Service Customer 2/2/3 dot1q ALA-A 3.4.2.1 SAP Configuration Considerations When configuring a SAP, consider the following: • An SAP is a local entity and only locally unique to a given device.
  • Page 50: Sdp Bindings

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide An SDP has the following characteristics: • An SDP is locally unique to a participating ISAM. The same SDP ID can appear on other service routers/ISAMs. • An SDP uses the system IP address to identify the far-end PE. •...
  • Page 51: Mpls

    “ports” (spoke SDPs and SAPs) and not transmitted on any mesh SDPs. SDP Encapsulation Types The Nokia service model uses encapsulation tunnels through the core to interconnect with service edge routers. An SDP is a logical way of referencing the entrance to an encapsulation tunnel. The following encapsulation types are supported: Layer 2 with LDP signaled.
  • Page 52: 3.6 Deploying And Provisioning Services

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Figure 4 Service Creation and Implementation Flow START CORE PERFORM PREREQUISITE CONFIGURATIONS: SERVICES CUSTOMER ACCOUNTS, SDPs, QoS POLICIES, FILTER POLICIES,LSPs SUBSCRIBER ACCESS OPERATOR CONSOLE GUI SERVICES OR CLI VIA TELNET OR DIRECT ATTACHMENT CREATE SERVICE TYPE, SPECIFYING SERVICE ID AND CUSTOMER ID CONFIGURE SAP/INTERFACE DEFINE PORT-ID...
  • Page 53: Phase 1: Core Network Construction

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.6.1 Phase 1: Core Network Construction Before the services are provisioned, the following tasks should be completed: • Build the IP or IP/MPLs core network. • Configure routing protocols. •...
  • Page 54: 3.8 Configuring Global Service Entities With Cli

    Configuring an SDP • Service Management Tasks 3.8.1 Service Model Entities The Nokia service model uses logical entities to construct a service. The service model contains four main entities to configure a service. • Service Distribution Points (SDPs) • Services: •...
  • Page 55: Configuring An Sdp

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview ------------------------------------------- customer 5 create description “Nokia Customer” contact “Technical Support” ------------------------------------------- A:A:ALA-12>configure>service# 3.8.3 Configuring an SDP The most basic SDP must have the following: • A locally unique SDP identification (ID) number.
  • Page 56: Configuring An Sdp

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3 Specify an encapsulation type. 4 Specify a far-end node. 3.8.3.2 Configuring an SDP When specifying MPLS SDP parameters, you can only specify a static LSP name, an RSVP-based LSP or enable LDP. There cannot be 2 methods of transport in a single SDP.
  • Page 57: Service Management Tasks

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.8.4 Service Management Tasks This section discusses the following service management tasks: • Modifying Customer Accounts • Deleting Customers • Modifying SDPs • Deleting SDPs • Modifying LSPs • Deleting LSPs 3.8.4.1 Modifying Customer Accounts...
  • Page 58: Deleting Sdps

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Example: configure>service# sdp 79 configure>service>sdp# description "Path-to-107" configure>service>sdp# shutdown configure>service>sdp# far-end "10.10.10.107" configure>service>sdp# path-mtu 1503 configure>service>sdp# no shutdown To match the incoming traffic’s TPID with SDP, you can use vlan-vc-etype. the following scenarios can occur: •...
  • Page 59: Deleting Lsps

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview configure>router>mpls# static-lsp to-headquarters configure>router>mpls>static-lsp# push 105 nexthop 138.3.5.27 configure>router>mpls>static-lsp# to 1.1.1.1 configure>router>mpls>static-lsp# no shutdown 3.8.4.6 Deleting LSPs The no form of the lsp command removes an LSP ID and all associated information. Before an LSP can be deleted, the LSP must be removed from all SDP associations.
  • Page 60: 3.10 Ethernet Connectivity Fault Management

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide description "MPLS-10.10.10.104" far-end 10.10.10.104 signaling tldp path-mtu 4462 no shutdown exit epipe 6000 customer 6 create service-mtu 1514 sap lt:1/1/2:0 create no shutdown exit spoke-sdp 2:6111 create no shutdown exit no shutdown exit...
  • Page 61: Table 3 Acronym Callout

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Table 3 Acronym callout Acronym Description Continuity check message Connectivity fault management ETH-CFM Ethernet Connectivity Fault Management Loopback message Loopback reply Linktrace message Linktrace reply Maintenance entity Maintenance association MA-ID Maintenance association identifier Maintenance domain...
  • Page 62 Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide • For VPLS and v-VPLS services: • CFM can be enabled or disabled on a SAP or SDP bindings basis. • Up and/or down MEP with a MEP-ID on a SAP and SDP binding for each MD level can be configured, modified, or deleted.
  • Page 63: Configuring Eth-Cfm With Cli

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.10.1 Configuring ETH-CFM with CLI This section provides information to configure global ETH-CFM parameters using the Command Line Interface (CLI). Topics in this section include: • Create a Maintenance Domain •...
  • Page 64: 3.11 G.8032 Ethernet Ring Protection Switching

    VID. G.8032 controls the active state for the data VLAN (ring data instances) associated with a control instance. Multiple control instances allow logically separate rings on the same topology. The Nokia implementation supports dot1q encapsulation for data ring instances and the control channel.
  • Page 65: Figure 5 Ring In The Initial State

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview R-APS messages are periodically sent around in both directions to tell other nodes in the Ring about the blocked port in the RPL owner node. In non-revertive mode any link may be the RPLY link.1731 Ethernet OAM CC is the basis of the RAPS messages used by nodes in the ring to monitor the health of each link in the ring in both directions.
  • Page 66: Figure 6 Ring In The Protection State

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Figure 6 Ring in the protection state Once the failed link recovers, the nodes that blocked the link again send the R-APS messages indicating no failure this time. This in turn triggers RPL Owner to block the RPL link and indicate the Blocked RPL link the ring in R-APS message, which when received by the nodes at the recovered link cause them to unblock that link and restore connectivity (again all nodes in the ring perform FBD Flush and MAC learning...
  • Page 67: Sample Configuration

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Ethernet R-APS can be configured on any port configured for access or hybrid mode using dot1q encapsulation enabling support for Ethernet RAPS protected services on the service edge towards the customer site, or within the Ethernet backbone. The intention of this is to cause minimum disruption to the service during Ethernet RAPS failure detection and recovery.
  • Page 68: Oam Considerations

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide no shutdown exit exit no shutdown no shutdown exit Associating eth-ring instance to a sap: Configure service vpls 20 customer 1 v-vpls vlan 100 create description "Ring Control VID 100" sap nt-a:xfp:1:100 eth-ring 1 create //control sap for path-a exit...
  • Page 69: Duplex Nt Erps Performance Considerations

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.11.5 Duplex NT ERPS Performance considerations This section suggests actions to be performed by the operator to optimize performance impacts in the event of Active-NT switchover on a Duplex Load-Balanced NT.
  • Page 70 Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 7 If ccm-errors need not be propagated to the ring path (operational status), configure all the defects as low-prio-defects for the eth-cfm mep of the corresponding path. 8 Configure a control SAP (on a v-VPLS service) for the ring path with VLAN as r-aps tag.
  • Page 71: 3.12 Dhcp Lease Query

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview *A:FAD-Chassis>configure>eth-ring>path# eth-cfm *A:FAD-Chassis>configure>eth-ring>path>eth-cfm# mep 11 domain 100 association 1 *A:FAD-Chassis>configure>eth-ring>path>eth-cfm>mep# control-mep *A:FAD-Chassis>configure>eth-ring>path>eth-cfm>mep# no shutdown *A:FAD-Chassis# configure service vpls 1002 customer 1 v-vpls vlan 1002 *A:FAD-Chassis>configure>service>vpls$ sap lag-30:1002 MINOR: SVCMGR #1602 The SAP-id is already in use - lag-30:1002 is already configured under Ethernet ring 10 *A:FAD-Chassis>configure>service>vpls$ sap lag-30:1002 eth-ring 10 *A:FAD-Chassis>configure>service>vpls>sap$...
  • Page 72: 3.13 Dhcp Remote Id Check

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide with 95 sessions for each type such as SLQ, BLQ IPv4, and BLQ IPv6, and with 5 queries x 19 LTs. IHUB supports lease query messages generated by the LT, and legacy behavior of forwarding LQ packets will be maintained.
  • Page 73: Public Tunnel Saps

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview • Public tunnel interface • This interface can be either an IES or VPRN interface • This interface represents the public side of the GRE tunnel • Private tunnel interface •...
  • Page 74: Gre Tunnel Configuration

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide In the above example, the IP address 10.0.0.1 is the address of the GRE tunnel endpoint from the perspective of the payload IP packets. This address belongs to the address space of the VPRN 1 service and is not exposed to the public IP network carrying GRE encapsulated packets.
  • Page 75: Statistics Collection

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview • oper state • type (GRE-only) 3.14.4 Statistics Collection GRE tunnel statistics are enabled or disabled dynamically using CLI commands. The statistics counter includes the number of Rx packets, Rx bytes, Tx packets, and Tx bytes.
  • Page 76: 3.16 Global Services Command Reference

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide • The same DHCPv6 PD is delegated to two different devices In this scenario, the PD is not delegated to the second Note — device, since it is considered to be an invalid delegation. Duplicate PD Alarm will be cleared in the following scenarios: •...
  • Page 77: Customer Management Commands

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.16.1.1 Customer Management Commands configure — service — customer customer-id [create] — [no] customer customer-id — contact contact-information — no contact contact-information — description description-string — no description — sdp-id mpls —...
  • Page 78: Show Commands

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide — [no] path {a|b} port-id raps-tag qtag/qinqtag — description description-string — eth-cfm — mep-id domain md-index association ma-index — ccm-enable — ccm-ltm-priority priority — control-mep — low-priority-defect{allDef|macRemErrXcon|remErrXcon|errXcon|xcon|noXcon} — mac-address xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx —...
  • Page 79: Description

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.1.1 description Table 4 description command Item Description Syntax description description-string no description Context configure>service>customer configure>eth-ring configure>eth-ring>path Description This command creates a text description stored in the configuration file for a configuration context.
  • Page 80: Customer

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3.17.2.1 customer Table 6 customer command Item Description Syntax customer customer-id [create] no customer customer-id Context configure>service Description This command creates a customer ID and customer context used to associate information with a particular customer.
  • Page 81: Sdp Commands

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.3 SDP Commands 3.17.3.1 Table 8 sdp command Item Description Syntax sdp sdp-id mpls no sdp sdp-id Context configure>service Description This command creates or edits a Service Distribution Point (SDP). SDPs must be explicitly configured.
  • Page 82: Far-End

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Table 9 adv-mtu-override command Item Description Syntax [no] adv-mtu-override Context configure>service>sdp sdp-id Description This command overrides the advertised VC-type MTU. When enabled, the ISAM signals a VC MTU equal to the service MTU (includes the Layer 2 header). Under normal operations it will advertise the service MTU minus the Layer 2 header.
  • Page 83: Ldp

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.3.4 Table 11 ldp command Item Description Syntax [no] ldp Context configure>service>sdp sdp-id Description This command enables LDP-signaled LSPs on MPLS-encapsulated SDPs. In MPLS SDP configurations either one LSP can be specified or LDP can be enabled. The SDP ldp and lsp commands are mutually exclusive.
  • Page 84: Path-Mtu

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command creates associations between one or more label switched paths (LSPs) and an Multi- Protocol Label Switching (MPLS) Service Distribution Point (SDP). This command is implemented only on MPLS-type encapsulated SDPs.
  • Page 85: Signaling

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.3.7 signaling Table 14 signaling command Item Description Syntax signaling {off | tldp} Context configure>service>sdp sdp-id Description This command specifies the signaling protocol used to obtain the ingress and egress labels in frames transmitted and received on the SDP.
  • Page 86: Vlan-Vc-Etype

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Special Cases Service Admin State - Bindings to an SDP within the service will be put into the out-of-service state when the service is shutdown. While the service is shutdown, all customer packets are dropped and counted as discards for billing and debugging purposes.
  • Page 87: Domain

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Table 17 eth-cfm command Item Description Syntax eth-cfm Context configure Description This command enables the context to configure 802.1ag CFM parameters 3.17.4.2 domain Table 18 domain command Item Description Syntax domain md-index [format {dns | mac | none | string}] name md-name level level domain md-index...
  • Page 88: Association

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3.17.4.3 association Table 19 association command Item Description Syntax association ma-index [format {icc-based | integer |string | vid | vpn-id}] name ma-name association ma-index no association ma-index Context configure>eth-cfm>domain Description This command configures the Maintenance Association (MA) for the domain The no form of the command removes the MA index parameters from the configuration.
  • Page 89: Mhf-Creation

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Item Description Parameters bridge-id - Specifies the bridge ID for the domain association. Values: 1...2147483647 (2 of 2) 3.17.4.5 mhf-creation Table 21 mhf-creation command Item Description Syntax mhf-creation {default | none | explicit} no mhf-creation Context configure>eth-cfm>domain>association>bridge-identifier...
  • Page 90: Remote-Mepid

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters interval — Specifies the interval between CCM transmissions to be used by all MEPs in the Values: 100 milliseconds, 1 second, 10 seconds, 60 seconds, and 600 seconds (2 of 2) 3.17.4.7 remote-mepid...
  • Page 91: Y1731Pm

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.4.9 y1731pm Table 25 y1731pm command Item Description Syntax domain md-index association ma-index mep mep-id session session-id [create] Context configure>eth-cfm>y1731pm Description This command creates a y1731pm session for the given mep. The no form of the command will remove the y1731pm session.
  • Page 92: Period

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Default Parameters priority — <0,1,2…7> (2 of 2) 3.17.4.12 period Table 28 period command Item Description Syntax period period Context configure>eth-cfm>y1731pm>domain Description The value of period specifies the time to wait between the transmission of one OAM request and the next.
  • Page 93: Measurement-Period

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.4.14 measurement-period Table 30 measurement-period command Item Description Syntax measurement-period period Context configure>eth-cfm>y1731pm>domain Description The value of measurement-period specifies the time after which the synthetic loss calculation is made periodically. If the value of this object is set to 'X' seconds, loss measurement calculations are done after every 'X' seconds.
  • Page 94: Ethernet Ring Global Commands

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>eth-cfm>y1731pm>domain Description The value of type indicates the type of y1731pm session this row details. The no form of the command reverts the value to the default. Default None.
  • Page 95: Ccm-Hold-Time

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Item Description Description Configures the Wait-To-Restore (WTR) Timer. RPL owner uses the WTR delay timer before initiating an RPL block in case of revertive mode of operation. WTR timer is used to prevent frequent redundancy transactions as result of an intermittent signal failure defects.
  • Page 96: Node-Id

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Table 36 guard-time command Item Description Syntax guard-time time Context configure>eth-ring Description Configure the eth-ring guard time Parameters time - eth-ring guard time in deciseconds Values: 1...20 Default: 5 3.17.5.5 node-id Table 37...
  • Page 97: Path

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview 3.17.5.7 path Table 39 path command Item Description Syntax path {a|b} port-id raps-tag qtag|qinqtag Context configure>eth-ring Description This command configures one of the two paths supported under the Ethernet ring. The no form of this command removes the path from under the Ethernet ring.
  • Page 98: Customer

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3.17.6.1 customer Table 41 customer command Item Description Syntax customer [customer-id] [site customer-site-name] Context show>service Description Displays service customer information. Parameters customer-id — Displays only information for the specified customer ID. Default: All customer IDs display.
  • Page 99: Table 44 Show Service Service-Using Command Output Fields

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Item Description Context show>service Description This command displays the services matching certain usage properties. If no optional parameters are specified, all services defined on the system are displayed. Parameters epipe —...
  • Page 100: Sdp

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide ============================================================================ *A:ALA-12# *A:ALA-12# show service service-using epipe ============================================================================ Services [epipe] ============================================================================ ServiceId Type CustomerId Last Mgmt Change ---------------------------------------------------------------------------- Epipe 06/22/2006 23:05:58 Epipe 06/22/2006 23:05:58 Epipe 06/22/2006 23:05:58 Epipe 06/22/2006 23:05:58 ---------------------------------------------------------------------------- Matching Services : 4 ============================================================================...
  • Page 101: Sdp-Using

    FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Item Description Parameters sdp-id — The SDP ID for which to display information. Default:All SDPs. Values: 1 — 17407 far-end ip-address — Displays only SDPs matching with the specified far-end IP address. Default: SDPs with any far-end IP address.
  • Page 102: Eth-Ring

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide Table 47 sdp-using command Item Description Syntax sdp-using [sdp-id[:vc-id] | far-end ip-address] Context show>service Description Display services using SDP or far-end address options. Parameters sdp-id — Displays only services bound to the specified SDP ID. Values: 1 —...
  • Page 103 FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview Item Description Description Display Ethernet ring status information (or) path information Parameters ring-index — Ethernet ring index. Values: 1 — 64 (2 of 2) Sample output: # show eth-ring ============================================================================ Ethernet Rings (summary) ============================================================================...
  • Page 104: Tools Command

    Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide LowestDefectPri : macRemErrXcon HighestDefect : none Defect Flags : None Mac Address : 00:07:72:ac:0d:a5 ControlMep : True CcmLtmPriority CcmTx CcmSequenceErr Fault Propagation : disabled LbRxReply LbRxBadOrder LbRxBadMsdu LbTxReply LbNextSequence LtNextSequence LtRxUnexplained ========================================================...
  • Page 105 FD 100/320Gbps NT and FX NT IHub Services Guide Services Overview state:TxInfo (Bytes) Time === ===== ================================================ ==== aAdd PROT: 0xb040 Sf(DNF ) Tx--> Blk --- 497 02:18:11.480 bAdd PROT: 0xb020 Tx--> Blk Blk 497 02:18:11.480 pdu B: 00:07:72:a8:54:a8-0x0000 Nr PROT: 0xb020 Rx<-- Blk Blk 497 02:18:26.080 PROT: 0xb040...
  • Page 106 Services Overview FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13...
  • Page 107: Virtual Leased Line Services

    4.2 Ethernet Pipe (Epipe) Services 4.2.1 Epipe Service Overview An Epipe service is Nokia’s implementations of an Ethernet VLL based on the IETF “Martini Drafts” (draft-martini-l2circuit-trans-mpls-08.txt and draft-martini-l2circuit-encapmpls-04.txt) and the IETF Ethernet Pseudo-wire Draft (draft-so-pwe3-ethernet-00.txt). An Epipe service is a layer 2 point-to-point service where the customer data is encapsulated and transported across a service provider’s IP or MPLS network.
  • Page 108: Traffic Management Support

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Figure 9 Epipe/VLL Service Customer 1 Customer 2 IP/MPLS Network EPIPE (VLL) Service 1 Customer 1 EPIPE (VLL) Service 2 Customer 2 4.2.2 Traffic Management Support An aggregate egress rate limiter can be associated to an Epipe service. The rate limiter applies to traffic associated to the service which egresses on regular ports (network ports).
  • Page 109: Vll Service Considerations

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Figure 10 Pseudo wire ISAM LSP1.1 VLL/ VPLS VLL/ VPLS LSP1.2 As shown in Figure 10, a Pseudo-Wire has been established between the ISAM and PE1. The MPLS tunnel passes through Router R1 as this is the shortest path between the ISAM and PE1.
  • Page 110: Sap Encapsulations And Pseudowire Types

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Figure 11 SDP Statistics for VPLS and VLL Services SDP 103 VPLS1 VPLS1 VPLS2 VPLS2 IP/MPLS SDP 101 SDP 102 VPLS2 VPLS1 4.3.2 SAP Encapsulations and Pseudowire Types The Epipe service is designed to carry Ethernet frame payloads, so it can provide connectivity between any two SAPs that pass Ethernet frames.
  • Page 111: Ingress Network Classification

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.3.3.2 Ingress Network Classification A service ingress network QoS policy defines the match criteria used to determine the Flow Class of each packet, entering via an SDP binding (i.e. PW). The operator can configure ingress network QoS policy for the service.
  • Page 112: Common Configuration Tasks

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.4.1 Common Configuration Tasks This section provides a brief overview of the tasks that must be performed to configure the VLL services and provides the CLI commands. 1 Associate the service with a customer ID.
  • Page 113: Configure Epipe Service Mtu Attribute

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services [cbs cbs-size] [pbs pbs-size] no rate-limit egress-network qos policy-id no qos ingress qos policy-id no qos ingress-network qos policy-id no qos sgt-qos policy-id no sgt-qos 4.4.2.2 Configure Epipe Service MTU Attribute Use the following CLI syntax to configure the MTU for the Epipe service.
  • Page 114 Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide This example configures a distributed service between ALA-1 and ALA-2. A:ALA-1> configure>service# epipe 5500 customer 5 create configure>service>epipe$description "Distributed epipe service to east coast" configure>service>epipe# sap lt:1/1/1:550 create configure>service>epipe>sap# ingress configure>service>epipe>sap>ingress# filter ip 1 configure>service>epipe>sap>ingress# exit...
  • Page 115: Configuring Sdp Bindings

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services exit exit ---------------------------------------------- A:ALA-2>configure>service# Configure ‘restricted-tagging’ on an SAP When 'restricted-tagging' is enabled on a SAP, only double-vlan-tagged packets arriving at the SAP will be forwarded. Packets with outer TPID as 0x8100 and inner TPID 0x8100 are alone considered as double-vlan-tagged packets.
  • Page 116: Figure 12 Sdps - Uni-Directional Tunnels

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Figure 12 SDPs — Uni-Directional Tunnels ALA-1 ALA-2 SDP 3 demux SPOKE-SDP 3 Epipe 2 for customer 6 SDP 2 SPOKE-SDP 2 Epipe 2 for demux customer 6 Use the following CLI syntax to create a spoke SDP binding with an Epipe service: configure>service# epipe service-id [customer customer-id] spoke-sdp sdp-id:vc-id [vc-type {ether|vlan}]...
  • Page 117 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services ingress filter ip 1 exit egress filter ip 2 exit exit spoke-sdp 2:123 create ingress vc-label 6600 exit egress vc-label 5500 exit exit no shutdown exit ---------------------------------------------- A:ALA-1>configure>service# A:ALA-2>configure>service# info ----------------------------------------------...
  • Page 118: Sdp Bindings

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.4.3 Configuring Management Points (MEPs/MIPs) for Ethernet CFM on SDP bindings Two steps are required to configure the CFM in an EPIPE network: 1 The MD and MA need to be created first 2 The MEP/MIP can be created in the EPIPE service instance, by associating it to a SDP binding and adding to the defined MD and MA.
  • Page 119: Using Spoke Sdp Control Words

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services no shutdown 4.4.4 Using Spoke SDP Control Words When control word is enabled, the Admin Control Word is set to Preferred. It is necessary that both sides of the VLL have control word enabled or disabled for the pipe to be up.
  • Page 120: Service Management Tasks

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.4.5 Service Management Tasks This section discusses the following service management tasks: • Modifying Epipe Service Parameters • Disabling an Epipe Service • Re-enabling an Epipe Service •...
  • Page 121: Re-Enabling An Epipe Service

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services configure>service>epipe# shutdown configure>service>epipe# exit 4.4.5.3 Re-enabling an Epipe Service Use the following command to re-enable an Epipe service that was shut down: configure>service> epipe service-id no shutdown Example: configure>service# epipe 2 configure>service>epipe# no shutdown...
  • Page 122: Vll Services Cli Command Reference

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.5 VLL Services CLI Command Reference This section shows the following command hierarchies: • Epipe Service Configuration Commands • Show Commands • Clear Commands 4.5.1 Epipe Service Configuration Commands configure —...
  • Page 123: Show Commands

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services — ccm-ltm-priority priority — no ccm-ltm-priority — low-priority-defect{allDef|macRemErrXcon|remErrXcon|errXcon|xcon|noXcon} — mac-address mac-address — no mac-address — [no] shutdown — [mac mac-address] — default-mac — no — vlan-dot-1q-etype etype —...
  • Page 124: Generic Commands

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.1 Generic Commands 4.6.1.1 shutdown Table 51 shutdown command Item Description Syntax [no] shutdown Context configure>service>epipe configure>service>epipe>sap configure>service>epipe>spoke-sdp configure>service>epipe>spoke-sdp>eth-cfm>mep Description This command administratively disables an entity. When disabled, an entity does not change, reset, or remove any configuration settings or statistics.
  • Page 125: Vll Global Commands

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Item Description Context configure>service>epipe configure>service>epipe>sap Description This command creates a text description stored in the configuration file for a configuration context. The description command associates a text string with a configuration context to help identify the content in the configuration file.
  • Page 126: Service-Mtu

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters service-id — The unique service identification number identifying the service in the service domain. This ID must be unique to this service and may not be used for any other service of any type.
  • Page 127: Sgt-Qos

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Table 55 MTU Values for Specific VC Types VC-Type Example Advertised MTU Service MTU Ethernet 1514 1500 Ethernet (with preserved dot1q) 1518 1504 VLAN (dot1p transparent to MTU value) 1514 1500 VLAN (QinQ with preserved bottom Qtag)
  • Page 128 Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command creates a Service Access Point (SAP) within a service. A SAP is a combination of port and encapsulation parameters which identifies the service access point on the interface and within the ISAM.
  • Page 129: Restricted-Tagging

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.3.2 restricted-tagging Table 58 restricted-tagging command Item Description Syntax restricted-tagging no restricted-tagging Context configure>service>epipe configure>service>epipe>sap Description This command enables restricted-tagging for the SAP. 4.6.4 Service Filter and QoS Policy Commands 4.6.4.1 egress Table 59...
  • Page 130: Ingress

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.4.3 ingress Table 61 ingress command Item Description Syntax ingress Context configure>service>epipe configure>service>epipe>sap Description This command enables the context to configure ingress parameters for the service and the SAP.
  • Page 131: Qos

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Item Description Description This command associates an IP or MAC filter policy with an ingress or egress Service Access Point (SAP). Filter policies control the forwarding and dropping of packets based on IP or MAC matching criteria.
  • Page 132: Qos

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters policy-id — The access QoS policy ID to associate with the service on ingress. The policy ID must already exist. Values: 1 — 65535 (2 of 2) 4.6.4.7 Table 65...
  • Page 133: Rate-Limit

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.4.8 rate-limit Table 66 rate-limit command Item Description Syntax rate-limit cir cir-rate pir pir-rate [cbs cbs-size] [pbs pbs-size] no rate-limit Context configure>service>epipe>egress Description This command defines the aggregate egress rate limit for the Epipe service. It applies to traffic associated to the service which is egressing on regular ports (network ports).
  • Page 134 Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command binds a service to an existing Service Distribution Point (SDP). A spoke SDP is treated like the equivalent of a traditional bridge “port” where flooded traffic received on the spoke SDP is replicated on all other “ports”...
  • Page 135: Control-Word

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.5.2 control-word Table 68 control-word command Item Description Syntax [no] control-word Context configure>service>epipe>spoke-sdp Description This command indicates whether the control word is used or not. The value of the control word is negotiated with the peer.
  • Page 136: Egress

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.5.4 egress Table 70 egress command Item Description Syntax egress Context configure>service>epipe>spoke-sdp Description This command configures the egress SDP context. 4.6.5.5 ingress Table 71 ingress command Item Description Syntax ingress...
  • Page 137: Vc-Label

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.5.7 vc-label Table 73 vc-label command Item Description Syntax [no] vc-label egress-vc-label Context configure>service>epipe>spoke-sdp>egress Description This command configures the egress VC label. Parameters vc-label — A VC egress value that indicates a specific connection. Values: 16 —...
  • Page 138: Eth-Cfm

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command specifies an explicit dot1q value used when encapsulating to the SDP far end. When signaling is enabled between the near and far end, the configured dot1q tag can be overridden by a received TLV specifying the dot1q value expected by the far end.
  • Page 139: Ccm-Enable

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Item Description Parameters mep-id - MEP Identifier Values: 1...8191 md-index - Maintenance Domain Identifier Values: 1...4294967295 ma-index - Maintenance Association Identifier. Values: 1...4294967295 direction - Specifies the direction of the MEP. Values: up/down Default value: down (2 of 2)
  • Page 140: Low-Priority-Defect

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.5.14 low-priority-defect Table 80 low-priority-defect command Item Description Syntax low-priority-defect { allDef | macRemErrXcon | remErrXcon | errXcon | xcon | noXcon} Context configure>service>epipe>spoke-sdp>eth-cfm>mep Description This command specifies the lowest priority defect that is allowed to generate a fault alarm. Default macRemErrXcon Parameters...
  • Page 141: Mip

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.5.16 Table 82 mip command Item Description Syntax mip [mac mac-address] mip default-mac no mip Context configure>service>epipe>spoke-sdp>eth-cfm Description This command enables/disables Maintenance Intermediate Points (MIP) Parameters mac-address - The MAC address of the MIP in xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx format. Value: xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx default-mac - keyword.
  • Page 142: Show Commands

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.6 Show Commands 4.6.6.1 egress-label Table 84 egress-label command Item Description Syntax egress-label start-label [end-label] Context show>service Description This command displays services using the range of egress labels. If only the mandatory start-label parameter is specified, only services using the specified label are displayed.
  • Page 143: Ingress-Label

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.6.2 ingress-label Table 86 ingress-label command Item Description Syntax ingress-label start-label [end-label] Context show>service Description This command displays services using the range of egress labels. If only the mandatory start-label parameter is specified, only services using the specified label are displayed.
  • Page 144: Sap-Using

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.6.3 sap-using Table 88 sap-using command Item Description Syntax sap-using [sap sap-id] sap-using [ingress | egress] filter filter-id Context show>service Description This command displays SAP information. If no optional parameters are specified, the command displays a summary of all defined SAPs. The optional parameters restrict output to only SAPs matching the specified properties.
  • Page 145: Sdp

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Table 89 Show Service SAP Output Fields Label Description Port ID The ID of the access or hybrid port where the SAP is defined. Svc ID The service identifier. Sap MTU The SAP MTU value.
  • Page 146: Sdp-Using

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Table 91 Show Service SDP Output Fields Label Description SDP Id The SDP identifier. Adm MTU Specifies the desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented.
  • Page 147: Table 93 Show Service Sdp-Using Output Fields

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Item Description Parameters sdp-id — Displays only services bound to the specified SDP ID. Values: 1 — 17407 vc-id — The virtual circuit identifier. Values: 1 — 4294967295 far-end ip-address —...
  • Page 148: All

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters service-id — The service identification number that identifies the service in the domain. all — Display detailed information about the service. base — Display basic service information. labels —...
  • Page 149 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Label Description Flags Specifies the conditions that affect the operating status of this SAP. Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, PortMTUTooSmall, L2OperDown, SapIngressQoSMismatch, SapEgressQoSMismatch,RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, NoSapIpipeCeIpAddr, TodResourceUnavail, TodMssResourceUnavail, SapParamMismatch, CemSapNoEcidOrMacAddr, StandByForMcRing, ServiceMTUTooSmall, SapIngressNamedPoolMismatch,...
  • Page 150 Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Service Id The service identifier. Port Id The ID of the access or hybrid port where this SAP is defined. Description Generic information about the SAP. Encap Value The value of the label used to identify this SAP on the access or hybrid port.
  • Page 151: Base

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Label Description Out profile The number of out-of-profile packets or octets (rate above CIR) forwarded. forwarded Out profile dropped The number of out-of-profile packets or octets discarded. Service Access Points Managed by Service Specifies the service-id of the management VPLS managing this SAP.
  • Page 152: Labels

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Label Description SAP Count The number of SAPs defined on the service. SDP Bind Count SDP Bind Count Identifier Specifies the service access (SAP) and destination (SDP) points. Type Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on the SDP.
  • Page 153: Sap

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services 4.6.6.10 Table 101 sap command Item Description Syntax sap sap-id detail Context show>service>id Description This command displays information for the SAPs associated with the service. If no optional parameters are specified, a summary of all associated SAPs is displayed.
  • Page 154: Sdp

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide 4.6.6.11 Table 103 sdp command Item Description Syntax sdp sdp-id far-end ip-addr detail Context show>service>id Description Displays information for the SDPs associated with the service. If no optional parameters are specified, a summary of all associated SDPs is displayed. Parameters sdp-id —...
  • Page 155: Clear Commands

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Leased Line Services Label Description Signaling Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP. Admin State The administrative state of the Keepalive process. Oper State The operational state of the Keepalive process.
  • Page 156: Counters

    Virtual Leased Line Services FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sdp-id — The spoke SDP ID to be reset. Values: 1 — 17407 vc-id — The virtual circuit ID on the SDP ID to be reset. Values: 1 —...
  • Page 157: Virtual Private Lan Service

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5 Virtual Private LAN Service 5.1 In This Chapter 5.2 VPLS used in the NT 5.3 ISAM VPLS implementation 5.4 VPLS feature enhancements 5.5 Configuring a VPLS Service with CLI 5.6 Configuration Overview 5.7 Configuration Workflow 5.8 Configuring VPLS Components...
  • Page 158: Vpls Used In The Nt

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.2 VPLS used in the NT The ISAM NT makes use of the m-VPLS service, the v-VPLS service for VLAN-based services over a EMAN network and the VPLS service for L2 VPN using PW over a MPLS/IP network.
  • Page 159: Isam Vpls Implementation

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Hybrid ports can only be of the regular category. They inherit the features of both network ports and regular access ports. Access ports are defined for the IHub as residential or regular, by a port table that is auto-created by the system at startup time.
  • Page 160: V-Vpls

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide To support L2CP protocols running on top of a LAG, m-VPLS SAPs must be created on the LAG itself. 5.3.2 v-VPLS 5.3.2.1 v-VPLS usage The v-VPLS forwarders emulate the ISAM bridging service in the IHUB. Typical of bridging, a v-VPLS operates in the context of a VLAN.
  • Page 161: Figure 15 Nt V-Vpls Forwarding

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 15 NT v-VPLS forwarding DHCP snooping/ Static config. Relay RSTP/ Network ports MSTP ports ibridge IGMP snooping m-VPLS DHCP snooping/ Static config. Relay EMAN ibridge Network v-VPLS IP Edge DHCP snooping/...
  • Page 162: V-Vpls Saps

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide • Forwarding Information Base (FIB) management features on a per service level including: • Configurable FIB size limit. • FIB size alarms. • MAC learning disable. • User-to-user communication control for services configured on residential (user) ports.
  • Page 163: Mix Of Vpls And Vprn

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service The following apply to v-VPLS SAP configuration: • An SAP can only be configured on dot1q Ethernet encapsulation access/hybrid ports. • The v-VPLS operates in the context of a homogeneous VLAN ID, where all Ethernet dot1q v-VPLS SAPs must refer to the v-VPLS VLAN ID.
  • Page 164: Residential And Regular Port Usage

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.3.2.4 Residential and regular port usage The v-VPLS behavior distinguishes between the user-side (SAPs built on residential ports) and the network-side (SAPs built on regular ports or on LAGs made of regular ports), to secure control over MAC learning capabilities, and enable the ability to control user-to-user communication.
  • Page 165: Figure 18 Vprn And V-Vpls Virtual Port Interconnection Model

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 18 VPRN and v-VPLS virtual port interconnection model v-VPLS Vlan 17 My-Own-MAC@ VPRN_1 v-VPLS Vlan 19 My-Own-MAC@ VPRN_2 v-VPLS Vlan 23 My-Own-MAC@ Legend: Virtual port Figure 19 SAPs and virtual port object model v-VPLS All SAPs must...
  • Page 166: V-Vpls Mac Learning And Packet Forwarding

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide The virtual port plays the role of a physical connection between a v-VPLS and VPRN. The virtual port is auto-created at NT start-up time and is automatically associated with each v-VPLS instance when the v-VPLS is created.
  • Page 167: V-Vpls Traffic Processing

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service • When a frame is received from an SAP and the source MAC address conflicts with an entry in the FDB which was already self-learned (a dynamic FDB entry) on another SAP: •...
  • Page 168: Table 109 L2Cp And Lacp Destination Mac Address Definitions

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Table 109 L2CP and LACP destination MAC address definitions Frame type Destination MAC address L2CP pause frames 01-80-C2-00-00-01 L2CP frames L2CP frames include: • 01-80-C2-00-00-00 through 01-80-C2-00-00-0F •...
  • Page 169: Vpls

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.3.3 VPLS 5.3.3.1 VPLS usage Virtual Private LAN Service (VPLS) as described in Internet Draft draft-ietf-ppvpn-vpls-ldp-01.txt, is a class of virtual private network service that allows the connection of multiple sites in a single bridged domain over a provider-managed IP/MPLS network.
  • Page 170: Vpls Mac Learning And Packet Forwarding

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide VPLS is provided over MPLS by: • Connecting bridging-capable provider edge routers with a full mesh of MPLS LSP (label switched path) tunnels. • Negotiating per-service VC labels using draft-Martini encapsulation. •...
  • Page 171: Vpls Packet Walkthrough

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.3.3.3 VPLS Packet Walkthrough This section provides an example of VPLS processing of a customer packet sent across the network from site-A, which is connected to PE-Router-A, to site-B, which is connected to PE-Router-C (see Figure 20).
  • Page 172: Figure 22 Network Port Egress Packet Format And Flooding

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 2 PE-Router-A learns the source MAC address in the packet and creates an entry in the FIB table that associates the MAC address to the service access point (SAP) on which it was received.
  • Page 173: Figure 23 Access Port Egress Packet Format And Lookup

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Core Router Switching • All the core routers ('P' routers in IETF nomenclature) between PE-Router-A and PE-Rout- er-B and PE-Router-C are Label Switch Routers (LSRs) that switch the packet based on the transport (outer) label of the packet until the packet arrives at far-end PE-Router.
  • Page 174: Vpls Feature Enhancements

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.4 VPLS feature enhancements This section describes v-VPLS and m-VPLS supported enhancements and features. 5.4.1 Local and Remote Aging Timers Like a Layer 2 switch, learned MACs within a VPLS instance can be aged out if no packets are sourced from the MAC address for a specified period of time (the aging time).
  • Page 175: Fib Size

    5.4.7 VPLS and Spanning Tree Protocol Nokia’s VPLS service emulates a bridged or switched Ethernet Layer 2 network. The ISAM uses m-VPLS SAPs configured on ports or a LAG to forwards Ethernet packets into the m-VPLS service. The ISAM participating in the service learns where the customer MAC addresses reside, on ingress SAPs.
  • Page 176: Spanning Tree Operating Modes

    If SAPs are connected together, either through misconfiguration or for redundancy purposes, loops can form and flooded packets can keep flowing through the network. Nokia’s implementation of the Spanning Tree Protocol (xSTP) is designed to remove these loops from the VPLS topology. This is done by putting one or several SAPs in the discarding state.
  • Page 177: Multiple Spanning Tree

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service correctly. This would result in a slow transition to a forwarding state (30 seconds). For this reason, in the comp-dot1w mode, these BPDUs contain the port's port priority vector (conforms to 802.1w).
  • Page 178: Mstp General Principles

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.4.7.4 MSTP General Principles MSTP represents modification of RSTP which allows the grouping of different VLANs into multiple MSTIs. To enable different devices to participate in MSTIs, they must be consistently configured.
  • Page 179: Xstp High Availability

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service The T-LDP control plane behavior will be the same as the control word for VLL services. This means that an ISAM PE will not be able to negotiate with the peer PE whether the control word should be used.
  • Page 180: Figure 24 Management Model

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.4.8.3 Ingress Network Classification (only VPLS) A service ingress network QoS policy defines the match criteria used to determine the Flow Class of each packet, entering via an SDP binding (i.e. PW). The operator can configure ingress network QoS policy for the service.
  • Page 181: Pm Counters Per Sap

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service The VPLS management VRF only supports routing packets to locally attached hosts. That is, no next-hops can be statically specified and no routing protocols can be activated. To address the VPLS management VRF, the router instance vpls-management must be specified in CLI commands.
  • Page 182 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide When using the per service configurable TPID for a VPLS or EPIPE service (not for v-VPLS services), there are the following known limitations: • It is not possible to drop dataplane traffic in case the TPID does not match the service TPID (vlan-dot1q-etype).
  • Page 183: Figure 25 Configurable Tpid

    5.4.12 External Packet Forwarding (EPF) External Packet Forwarding is an Nokia proprietary feature to support Lawful intercept in a H.248 based voice network. To support this in IHUB, the IP address of a router 'R' will be configured in a v-VPLS which carries voice traffic.
  • Page 184: Figure 26 External Packet Forwarding

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Figure 26 External Packet Forwarding Router “R” ISAM-V MPLS VPN VoIP 7600 source dest VoIP platform source dest VLAN Voice & H.248 VLAN OAM NT I/O interface ISAM 5.4.12.1 Configuration Model...
  • Page 185: Configuring A Vpls Service With Cli

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service When the EPF IP is already configured on the v-VPLS, the following restrictions are enforced: • a virtual port SAP cannot be removed from the VPRN / IES interface, •...
  • Page 186: Configuration Overview

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.6 Configuration Overview The ISAM supports configuration of three types of VPLS services: • multiple v-VPLS instances can be configured to support L2 data frame forwarding between the user side and network sides via the IHub and VPRN interface reach extension •...
  • Page 187 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service The following configuration elements can be specified for m-VPLS after the service is created: • service description • STP, RSTP or MSTP instances • admin status up or down Since the m-VPLS does not forward traffic, it has no Note —...
  • Page 188: Configuration Workflow

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide *A:ALA-2>config>service# info ---------------------------------------------- vpls 9000 customer 6 create description "This is a distributed VPLS." def-mesh-vc-id 750 shutdown exit sap lt:1/1/5:16 create description "VPLS SAP" exit spoke-sdp 2:22 create exit mesh-sdp 8:750 create exit...
  • Page 189: Configuring Vpls Components

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 4 Define mesh/spoke SDP's for the VPLS (optional) • Associate the service to an existing SDP 5 Modify STP default parameters for the m-VPLS (optional). 6 Modify v-VPLS parameters such as user-to-user communication, mac learning and aging, FDB database size (optional).
  • Page 190 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide exit exit no shutdown ---------------------------------------------- *A:ALA-1>configure>service>vpls# Multiple v-VPLS instances can be configured for the ISAM. Note that the customer ID must be specified when creating the service, but is optional when making modifications.
  • Page 191 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service • The service ID must be unique to the service domain. Specifying an existing service ID enters the editing context for that service ID. • The admin status is down when the service is created and must be enabled using the no shutdown command.
  • Page 192: Configuring V-Vpls/Vpls Parameters

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide • Restricted MAC move is enabled (i.e MACs learned on regular ports overrule MACs learned on residential ports; MACs learned on residential ports cannot override MACs learned on regular ports). •...
  • Page 193: Mac Learning And Aging

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.8.2.3 MAC learning and aging Learning of new MAC addresses in the v-VPLS/VPLS forwarding database (FDB) can be enabled and disabled for the service instance using the disable-learning command.
  • Page 194: User-To-User Communication

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide • query-interval: The configured default value for (dynamic) MR SAPs when these SAPs cannot learn the query-interval from the received QUERY messages (for example, because these are not filled in the QUERY message). The system assumes an external querier is shutdown when no QUERY is ×...
  • Page 195: Unrestricted Mac Move

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.8.2.6 Unrestricted MAC move The VPLS behavior distinguishes between the user side and network side, to secure control over MAC learning capabilities. MAC learning on regular access ports or on SDP bindings has by default priority over MACs learned on residential SAPs.
  • Page 196: External Packet Forwarding

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide sap nt-a:xfp:2:500 create exit no shutdown --------------------------------------------------------------- >configure>service>vpls# >configure>port>nt-a:xfp:2:500>ethernet --------------------------------------------------------------- use-vlan-dot1q-etype ------------------------------------------------------------------- To disable the use of an alternate TPID, use the no vlan-dot1q-etype command. >configure>service>vpls# info ------------------------------------------------------------- [no] vlan-dot1q-etype <etype>...
  • Page 197: Configuring Spanning Tree Protocols On M-Vpls

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service extfwd device-ip 10.1.1.2 exit shutdown exit exit vprn 1001 customer 1 create shutdown interface "epf_vprn" create address 10.1.1.1/30 sap nt:vp:1:1000 create exit exit exit ----------------------------------------------- 5.8.3 Configuring Spanning Tree Protocols on m-VPLS RSTP and MSTP are supported on the m-VPLS only, not on a v-VPLS.
  • Page 198: Configuring Stp Bridge Parameters

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.3.1 Configuring STP Bridge Parameters Modifying some of the Spanning Tree Protocol parameters allows the operator to balance STP between resiliency and speed of convergence extremes. Modifying particular parameters, mentioned below, must be done in the constraints of the following two formulae: 2 x (Bridge_Forward_Delay - 1.0 seconds) >= Bridge_Max_Age...
  • Page 199 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service • mstp-comp-2003 Compliant with the Multiple Spanning Tree Protocol specified in IEEE 802.1Q-REV/D3.0-04/2005 but with some changes to make it backwards compatible to 802.1Q 2003 edition and IEEE 802.1w. •...
  • Page 200 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide configure>service>vpls service-id# stp max-age max-info-age • Range: 6 to 40 seconds • Default: 20 seconds • Restore Default: no max-age Forward Delay RSTP, as defined in the IEEE 802.1D-2004 standards, will normally transition to the forwarding state via a handshaking mechanism (rapid transition), without any waiting times.
  • Page 201 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Hold Count The hold-count command configures the peak number of BPDUs that can be transmitted in a period of one second. configure>service>vpls service-id# stp hold-count count-value • Range: 1 to 10 •...
  • Page 202: Configuring Vpls Saps

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.4 Configuring VPLS SAPs A default QoS policy is applied to each ingress and egress SAP. Additional QoS policies can be configured in the configure>qos context.VPLS services use SAPs to associate the service with a dot1q Ethernet encapsulation access physical port or LAG.
  • Page 203: Vpls Sap Configuration Example

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.8.4.2 VPLS SAP configuration example To configure a local VPLS service, enter the sap sap-id command twice with different port IDs in the same service configuration. configure service vpls <service-id> sap {<port-id> | <lag-id>}:<vlan-id> create The following CLI command syntax to create or modify an SAP: configure service vpls <service-id>...
  • Page 204 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide For SDP binding information, see “Configuring SDP Bindings”. The following example displays a configuration of VPLS SAPs configured for ALA-1, ALA-2, and ALA-3. *A:ALA-1>config>service# info -------------------------------------------- vpls 9000 customer 6 vpn 750 create description "Distributed VPLS services."...
  • Page 205: Configuring Vpls Sap Parameters

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.8.5 Configuring VPLS SAP Parameters After an SAP is created for a service, you can modify SAP parameters including IP and MAC filter policies, static MAC, and SAP specific RSTP/MSTP parameters. 5.8.5.1 Configuring egress and ingress filter policies on an You can associate an IP or MAC filter policy with an ingress or egress Service...
  • Page 206 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide • SAP Admin Down An administratively down state allows a service provider to prevent an SAP from becoming operationally blocked. BPDUs will not originate out the SAP towards the customer.
  • Page 207 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service The default value for SAP priority is 128. This parameter can be modified within a range of 0 to 255, 0 being the highest priority. Masking causes the values actually stored and displayed to be 0 to 240, in increments of 16.
  • Page 208: Configuring Sap-Specific Igmp Parameters

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.5.4 Configuring SAP-specific IGMP Parameters The following SAP-specific IGMP parameters can be configured: • mrouter-port: This command specifies whether a multicast router is attached behind this SAP. configure service vpls service-id sap sap-id igmp-snooping mrouter-port When configuring an SAP as an mrouter-port, then IGMP REPORTS generated by the IGMP subsystem of the containing v-VPLS/VPLS are sent out on this SAP.
  • Page 209 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service • query-interval: This command configures the interval between two consecutive general QUERIES sent out by the IGMP subsystem on this SAP. configure service vpls service-id sap sap-id igmp-snooping query-interval seconds The configured query-interval must be greater than the configured query-response-interval.
  • Page 210: Configuring "Restricted-Tagging" On An Sap

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.5.5 Configuring “restricted-tagging” on an SAP When “restricted-tagging” is enabled on an SAP, only double-vlan-tagged packets arriving at the SAP will be forwarded. Only packets with outer TPID as 0x8100 and inner TPID 0x8100 are considered as double-vlan-tagged packets.
  • Page 211 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service When creating the MEP, MDs and MAs are associated and in addition, the following parameters are required: • MEP-ID - The ID value used to identify the MEP in the MA. This ID value must be listed in the remote-MEP-iD list in the MA configuration of the other PE router.
  • Page 212: Enabling Statistics Collection And Pm Collection On An Sap

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.5.7 Enabling Statistics collection and PM collection on an SAP Statistics collection and PM collection are enabled on an SAP when “enable-stats” is configured on that SAP. The operator can then monitor ingress packets/octets and egress packets/octets on an SAP.
  • Page 213: Operationally Disabled

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.8.6.1 Operationally Disabled Operationally disabled is the normal operational state for STP on an SAP in a VPLS that has any of the following conditions: • VPLS state administratively down •...
  • Page 214: Configuring Sdp Bindings

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.8.7 Configuring SDP Bindings A spoke SDP is treated like the equivalent of a traditional bridge port where flooded traffic received on the spoke SDP is replicated on all other "ports" (other spoke and mesh SDPs or SAPs) and not transmitted on the port it was received (unless a split horizon group was defined on the spoke SDP).
  • Page 215: Figure 27 Uni-Directional Tunnels

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 27 Uni-Directional Tunnels ALA-1 ALA-2 MESH-SDP 3 VPLS 9000 VPLS 9000 MESH-SDP 4 Customer 6001 Customer 6001 Spoke-SDP 21 Spoke-SDP 11 Spoke-SDP 22 Spoke-SDP 10 MTU A MTU C VPLS 9000 Customer 6001...
  • Page 216 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide vlan-vc-tag 0..4094 no shutdown static-mac ieee-address vlan-vc-tag [0..4094] The following displays SDP binding configurations for ALA-1, ALA-2, and ALA-3 for VPLS service ID 9000 for customer 6: *A:ALA-1>config>service# info ---------------------------------------------- vpls 9000 customer 6 create...
  • Page 217: Service Management Tasks

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service exit spoke-sdp 2:22 create exit mesh-sdp 5:750 create exit mesh-sdp 7:750 create exit no shutdown exit ---------------------------------------------- *A:ALA-3>config>service# 5.9 Service Management Tasks This section discusses the following service management tasks: •...
  • Page 218: Enabling And Disabling Vpls Entities

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide shutdown exit sap lt:1/1/5:22 create description “VPLS SAP” exit no shutdown ---------------------------------------------- *A:ALA-1>configure>service>vpls# To display a list of services, use the show service service-using vpls command. Enter the parameter such as description and/or SAP command syntax, and then enter the new information.
  • Page 219: Deleting A Vpls Service Or Sap

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service For example: configure service vpls 1 configure service vpls 1 shutdown configure>service>vpls1>exit 5.9.3 Deleting a VPLS Service or SAP A VPLS service cannot be deleted until SAPs are unbound (deleted), interfaces are shutdown, and the service is shutdown on the service level.
  • Page 220: Clearing Vpls Operational Data

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide *A:SetupCLI# show service id 17 fdb ==================================================================== Forwarding Database, Service 17 ==================================================================== Service Id : 17 Service Type : v-VPLS Table Size : 250 Total Count Learned Count Static Count OAM-learned Count : 0 Host-learned Count: 0...
  • Page 221: Showing Vpls Sap Operational Data

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.9.6 Showing VPLS SAP operational data The operator can show SAP operational data including the following: • Summary information • All information • STP statistics • SAP statistics •...
  • Page 222: Bgp Ad Overview

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.10.1 BGP AD Overview The BGP protocol establishes neighbor relationships between configured peers. An open message is sent after the completion of the three-way TCP handshake. This open message contains information about the BGP peer sending the message.
  • Page 223: Table 110 Bgp Ad Nlri Versus Ip Vpn Nlri

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Table 110 BGP AD NLRI versus IP VPN NLRI BGP AD NLRI Usage IP VPN NLRI Usage Route Distinguisher (8 Octets) Route Distinguisher (8 Octets) VSI id (4) (IP Prefix) IP Prefix Network Layer Reachability Information (NLRI) is exchanged between BGP peers indicating how to reach prefixes.
  • Page 224: Bgp-Ad And Target Ldp (T-Ldp) Interaction

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide AII Type Length Value SAII Value (continued) AII Type Length Value TAII Value (continued) (2 of 2) Each of the FEC fields are designed as a sub-TLV equipped with its own type and length providing support for new applications.
  • Page 225: Figure 28 Bgp-Ad And T-Ldp Interaction

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 28 BGP-AD and T-LDP Interaction Reflector Cluster VPN 10 VPN 10 Legend: I-BGP Session 24382 5.10.4 SDP Usage Service Access Points (SAP) are linked to transport tunnels using Service Distribution Points (SDP).
  • Page 226: Automatic Creation Of Sdps

    The Nokia implementation provides for safe handling of pseudowire templates. Changes to the pseudowire templates are not automatically propagated. Tools are provided to evaluate and distribute the changes. The following command is used to distribute changes to a “pw-template”...
  • Page 227: Figure 29 Bgp Vpls Solution

    Both of these changes are service affecting. Other changes will not be service affecting. 5.11 BGP VPLS The Nokia BGP VPLS solution, compliant with RFC 4761, is described in this section. Figure depicts the service representation for BGP VPLS mesh.
  • Page 228: Pseudowire Signaling Details

    • VE Block size (VBS) — defines how many contiguous pseudowire labels are reserved starting with the Label Base • Nokia implementation always uses a value of eight • Label Base (LB) — local allocated label base • The next eight labels are allocated for remote PEs Thjs BGP update communicates to the other PE(s) to accept the RT in order to reach (VE-ID=x), use a pseudowire label of LB + VE-ID—VBO using the BGP NLRI for...
  • Page 229: Table 112 Layer2 Info Extended Community

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Assuming that VE-ID=10 is configured in another PE4 the following procedures applies: • PE4 sends BGP Update with the new VE-ID in the network that will be received by all the other participating PEs, including PE1.
  • Page 230: Table 113 Control Flags Bit Vector

    VPLS packets to this PE, depending on whether S is 1 or 0, respectively • C — a Control work MUST or MUST NOT be present when sending VPLS packets to this PE, depending on whether C is 1 or 0, respectively. By default, Nokia implementation uses 0 •...
  • Page 231: Bgp Vpls Configuration Procedure

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.11.2 BGP VPLS Configuration Procedure BGP VPLS configuration requires the setup of the MPLS infrastructure and VPLS instance: • create LSPs • create SDPs if manually provisioned ones are required •...
  • Page 232: Usage Case Example

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide • Layer 2 MTU — derived from service vpls service-mtu parameter • The same value must be used in all related BGP VPLS instances in the Remote PEs to ensure the related pseudowires will come up.
  • Page 233: Configuring Bgp Auto-Discovery

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Including the service id is not mandatory but it is recommended as it will reduce the scope of the command to only the affect service id. 5.12 Configuring BGP Auto-Discovery This section provides important information to explain the different configuration options used to populate the required BGP AD and generate the LDP generalized pseudowire-ID FEC fields.
  • Page 234: Figure 30 Bgp Ad Configuration Example

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Figure 30 BGP AD Configuration Example L2VPN BGP AD VPLS-id: 65535:100 VLS-id: 1.1.1.134 L2VPN BGP AD RD: 65535:100 VSI-id: 1.1.1.6 65535:100 65535:100 RT: 65535:100 PE134 Next-hop: Self MPLS-id= MPLS-id= 1.1.1.134/32...
  • Page 235: Table 114 Bgp-Ad Cli Command Tree

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service *A:PE6>config>service>vpls# info ---------------------------------------------- route-distinguisher 65535:100 route-target export target:65535:100 import target:65535:100 pw-template-bind 1 exit bgp-ad vpls-id 65535:100 vsi-id prefix 1.1.1.6 no shutdown exit sap 1/1/20:600.* create exit no shutdown ---------------------------------------------- *A:PE6>config>service>vpls# In many cases, VPLS connectivity is based on a pseudowire mesh.
  • Page 236: Table 116 Bgp Parameters And Sdp Bindings In Use Example Display: Pers6

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide PERs6># (2 of 2) Table 116 BGP parameters and SDP bindings in use example display: PERs6 PERs6># show service l2-route-table Services: L2 Route Information — Summary Service Svc Id L2-Routes (RD-Prefix) Next Hop...
  • Page 237: Figure 31 Bgp Vpls Example

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 31 BGP VPLS Example VPLS PE-24 VPLS IP/MPLS PE-26 VPLS PE-25 24384 The BGP VPLS is configured in the PE24, PE25, and PE26 using the commands shown in the following CLI examples.
  • Page 238: Ldp Signaling

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide exit no shutdown exit sap 1/1/19:600.* create exit no shutdown ---------------------------------------------- Example #3: *A:PE25>config>service>vpls# *A:PE26>config>service>vpls# info ---------------------------------------------- route-distinguisher 65026:600 route-target export target:65019:600 import target:65019:600 pw-template-bind 1 exit bgp-vpls max-ve-id 100 ve-name 26...
  • Page 239: Figure 32 Bgp Ad Triggering Ldp Functions

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Figure 32 BGP AD Triggering LDP Functions pw-template 1 pw-template 1 vpls 100 Customer 1 create vpls 100 Customer 1 create service-mtu 1478 service-mtu 1478 bgp-ad bgp-ad vpls-id 65535:100 vpls-id 65535:100 pw-template-bind 1...
  • Page 240: Table 119 Pw-Template Cli Tree

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Legend U — Label In Use, N — Label Not In Use, W — Label Withdrawn S — Status Signaled Up, D — Status Signaled Down E — Epipe Service, V — VPLS Service, M — Mirror Service A —...
  • Page 241: Table 120 Pw-Template-Bind Cli Syntax

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service A pw-template-bind command configured within the VPLS service under the bgp-ad subcommand is a pointer to the pw-template that should be used. If a VPLS service does not specify an import-rt list, then that binding applies to all route targets accepted by that VPLS.
  • Page 242 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.14 Configuring BGP Auto-Discovery with Non-Persistency BGP-AD configuration can be made non-persistently by configuring the MIB object svsConfigPersistentControl to false using SNMP set along with the VPLS service creation.
  • Page 243: Vpls Service Cli Command Reference

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.15 VPLS Service CLI Command Reference This section shows the following command hierarchies: • Global Commands • SAP Commands • Show Commands • Clear Commands • Debug Commands 5.15.1 VPLS Service Configuration Commands 5.15.1.1...
  • Page 244 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide — egress-network — policy-id — no — [no] endpoint endpoint-name [create] — description description-string — [no] ignore-standby-signaling — [no] revert-time {revert-time | infinite} — [no] static-mac ieee-address [create] —...
  • Page 245 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service — [no] shutdown — [no] static-mac ieee-mac-address — [no] vlan-vc-tag 0..4094 — mfib-table-size table-size — no mfib-table-size — no propagate-mac-flush — remote-age aging-timer — no remote-age — no send-flush-on-failure —...
  • Page 246: Sap Commands

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide — mst-revision revision-number — no mst-revision — priority bridge-priority — no priority — [no] shutdown — vlan-dot1q-etype etype — [no] vlan-dot1q-etype — [no] user-user-com — [no] pw-template policy-id [create] —...
  • Page 247: Show Commands

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service — robust-count count — no robust-count — [no] send-queries — static — group grp-ip-address — [no] group — source ip-address — [no] source — [no] starg — version version —...
  • Page 248: Clear Commands

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide — mfib [brief] [ip] — mfib group grp-address — mstp-configuration — [sap-id [detail | sap-stats]] — [sap-id curr-15min-stats] — [sap-id curr-day-stats] — [sap-id prev-15min-stats [interval-number interval-number]] — [sap-id prev-day-stats [interval-number interval-number]] —...
  • Page 249: Table 121 Shutdown Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service — [no] port-state — [no] sap-id debug — igmp — router — [no] interface [ip-int-name | ip-address] — [no] [ip-int-name] — [no] misc — [no] packet [query|v1-report|v2-report|v3-report|v2-leave][ip-int-name|ip-address] 5.16 VPLS Service CLI Configuration Commands The following commands are described below: •...
  • Page 250: Table 122 Description Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vpls configure>service>vpls>interface configure>service>vpls>mesh-sdp configure>service>vpls>mesh-sdp>eth-cfm>mep configure>service>vpls>egress>rate-limit-pbits configure>service>vpls>sap configure>service>vpls>sap>eth-cfm>mep configure>service>vpls>sap>stp configure>service>vpls>spoke-sdp configure>service>vpls>spoke-sdp>eth-cfm>mep configure>service>vpls>stp Description The shutdown command administratively disables an entity. When disabled, an entity does not change, reset, or remove any configuration settings or statistics.
  • Page 251: Table 123 Description Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters description-string - The description character string. Allowed values are any string up to 80 characters long composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
  • Page 252 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command creates or modifies a Virtual Private LAN Services (VPLS) instance. The configure service vpls command is used to create or maintain a v-VPLS service or an m-VPLS service, depending on the context specified by the operator.
  • Page 253: Table 125 Def-Mesh-Vc-Id Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.2 def-mesh-vc-id Table 125 def-mesh-vc-id command Item Description Syntax def-mesh-vc-id vc-id no disable-learning [vc-id] Context configure>service>vpls Description This command configures the value used by each end of a tunnel to identify the VC. If this command is not configured, then the service ID value is used as the VC-ID.
  • Page 254: Table 127 Disable-Learning Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.4 disable-learning Table 127 disable-learning command Item Description Syntax disable-learning no disable-learning Context configure>service>vpls configure>service>pw-template Description In the context of vpls: This command enables learning of new MAC addresses in the v-VPLS forwarding database (FDB) for the service instance.
  • Page 255: Table 129 Endpoint Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.6 endpoint Table 129 endpoint command Item Description Syntax endpoint endpoint-name [create] no endpoint Context configure>service>vpls Description This command configures a service endpoint. Parameter endpoint-name — Specifies an endpoint name, 32 chars maximum 5.16.2.7 ignore-standby-signaling Table 130...
  • Page 256: Table 132 Static-Mac Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters revert-time — [0..600 seconds] infinite — makes endpoint non-revertive (2 of 2) 5.16.2.9 static-mac Table 132 static-mac command Item Description Syntax static-mac ieee-address [create] no static-mac Context configure>service>vpls>endpoint...
  • Page 257: Table 134 Extfwd Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.11 extfwd Table 134 extfwd command Item Description Syntax extfwd Context configure>service>vpls Description This command enables the context to configure External Packet Forwarding (EPF) policies. 5.16.2.12 device-ip Table 135 device-ip command Item...
  • Page 258: Table 137 Interface Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters table-size — The maximum number of MAC entries in the forwarding database. Values: 1 — 131071 (2 of 2) 5.16.2.14 interface Table 137 interface command Item Description Syntax...
  • Page 259: Table 138 Address Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.15 address Table 138 address command Item Description Syntax address ip-address[/mask] no address Context configure>service>vpls>interface Description This command assigns an IP address, IP subnet, to a VPLS management router interface. Only one IP address can be associated with an IP interface.
  • Page 260: Table 140 Arp-Timeout Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.16 arp-timeout Table 140 arp-timeout command Item Description Syntax arp-timeout seconds no arp-timeout Context configure>service>vpls>interface Description This command configures the minimum time, in seconds, an ARP entry learned on the IP interface is stored in the ARP table.
  • Page 261: Table 142 Mesh-Dsp Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters seconds — The aging time for local MACs expressed in seconds. Values: 60 — 86400 (2 of 2) 5.16.2.18 mesh-sdp Table 142 mesh-dsp command Item Description Syntax...
  • Page 262: Table 143 Spoke-Sdp Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sdp-id — The SDP identifier. Values 1 — 17407 vc-id — The virtual circuit identifier. This value is used to validate the VC ID portion of each mesh SDP binding defined in the service.
  • Page 263 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This command binds a service to an existing Service Distribution Point (SDP). A spoke SDP is treated like the equivalent of a traditional bridge “port” where flooded traffic received on the spoke SDP is replicated on all other “ports”...
  • Page 264: Table 144 Control-Word Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.20 control-word Table 144 control-word command Item Description Syntax egress Context configure>service>vpls>mesh-sdp configure>service>vpls>spoke-sdp configure>service>pw-template Description This command enables the use of the control word on pseudowire packets in VPLS and enables the use of the control word individually on each mesh-sdp or spoke-sdp.
  • Page 265: Table 146 Egress Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This command enables the use of the hash label on a VLL, or VPLS service bound to LDP SDP. When this feature is enabled, the ingress LER is modified so that the result of the hash on the ingress packet header is communicated to the egress data path for use as index to select the value of the label field of the hash label.
  • Page 266: Table 148 Vc-Label Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command configures the ingress SDP context. (2 of 2) 5.16.2.24 vc-label Table 148 vc-label command Item Description Syntax [no] vc-label [egress-vc-label] Context configure>service>vpls>mesh-sdp>egress configure>service>vpls>spoke-sdp>egress Description This command configures the egress VC label.
  • Page 267: Table 150 Force-Vlan-Vc-Forwarding Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.26 force-vlan-vc-forwarding Table 150 force-vlan-vc-forwarding command Item Description Syntax [no] force-vlan-vc-forwarding Context configure>service>vpls>mesh-sdp configure>service>vpls>spoke-sdp configure>service>pw-template Description This command forces vc-vlan-type forwarding in the data path for spoke/mesh SDPs which have either vc-type.
  • Page 268: Table 153 Vlan-Vc-Tag Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command specifies the precedence of the SDP binding when there are multiple SDP bindings attached to one service endpoint. The value of zero can only be assigned to one SDP bind making it the primary SDP bind.
  • Page 269: Table 154 Vlan-Vc-Etype Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.30 vlan-vc-etype Table 154 vlan-vc-etype command Item Description Syntax vlan-vc-etype etype no vlan-vc-etype Context configure>service>pw-template Description This command enables the configuration of an alternate TPID value to be used at the pseudo wire template level.
  • Page 270: Table 156 Mfib-Table-Size Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.32 mfib-table-size Table 156 mfib-table-size command Item Description Syntax mfib-table-size size no mfib-table-size Context configure>service>vpls Description This command specifies the maximum number of (s,g) entries in the multicast forwarding database (MFIB) for the v-VPLS instance.
  • Page 271: Table 158 Remote-Age Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.34 remote-age Table 158 remote-age command Item Description Syntax remote-age aging-timer no remote-age Context configure>service>vpls Description Specifies the aging time for remotely learned MAC addresses in the forwarding database (FDB) for the Virtual Private LAN Service (VPLS) instance.
  • Page 272: Table 160 Service-Mtu Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.2.36 service-mtu Table 160 service-mtu command Item Description Syntax service-mtu octets no service-mtu Context configure>service>vpls Description This command configures the service payload (Maximum Transmission Unit – MTU), in bytes, for the service.
  • Page 273: Table 162 Sgt-Qos Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.37 sgt-qos Table 162 sgt-qos command Item Description Syntax sgt-qos sgt-qos-policy [no] sgt-qos Context configure>service>vpls Description This command enables the context to configure DSCP/Dot1p re-marking for self-generated traffic.
  • Page 274: Table 165 Storm-Control Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command enables and disables user to user communication for a v-VPLS service. It does not apply to m-VPLS. When enabled, user to user traffic is permitted between users on distinct SAPs.
  • Page 275: Table 167 Bgp-Vpls Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.42 bgp-vpls Table 167 bgp-vpls command Item Description Syntax bgp-vpls Context configure>service>vpls Description This command enables the context to configure the BGP-VPLS parameters and addressing. 5.16.2.43 max-ve-id Table 168 max-ve-id command Item...
  • Page 276: Table 169 Ve-Name Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command configures the allowed range for the VE-id value: locally configured and received in a NLRI. Configuration of a VE-id higher than the value specified in this command is not allowed.
  • Page 277: Table 170 Ve-Id Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This command creates or edits a ve-name. Just one ve-name can be created per BGP VPLS instance. The no form of this command removes the configured ve-name from the bgp vpls node. It can only be used when the BGP VPLS status is shutdown.
  • Page 278: Table 172 Bgp-Ad Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command administratively enables/disables the local BGP VPLS instance. On de-activation, an MP-UNREACH-NLRI must be sent for the local NLRI. The no form of the command enales the BGP VPLS addressing and the related BGp advertisement.
  • Page 279: Table 174 Route-Target Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This command binds the advertisements received with the route target (RT) that matches the configured list (either the generic or the specified import) to a specific pw-template. If the RT list is not present, the pw-template is used for all of them.
  • Page 280: Table 175 Vpls-Id Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Default no ve-name Parameters export ext-community — Specifies communities allowed to be sent to remote PE neighbors. import ext-community — Specify communities allowed to be accepted from remote PE neighbors.
  • Page 281: Table 177 Prefix Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.52 prefix Table 177 prefix command Item Description Syntax prefix low-order-vsi-id no prefix Context configure>service>vpls>bgp-ad>vsi-id Description This command specifies the low-order 4 bytes used to compose the Virtual Switch Instance Identifier (VSI-ID) to use for NLRI in BGP auto-discovery in this VPLS service.
  • Page 282: Table 179 L2-Route-Table Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Values ip-addr: a.b.c.d comm-val: 0..65535 as-number: 0..65535 ext-comm-val: 0..4294967295 (2 of 2) 5.16.2.54 l2-route-table Table 179 l2-route-table command Item Description Syntax l2-route-table [detail] [bgp-ad] [bg-vpls] Context show>service show>service>id...
  • Page 283: Table 181 Split-Horizon-Group Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.2.56 split-horizon-group Table 181 split-horizon-group command Item Description Syntax [no] split-horizon-group [group-name] Context config>service>pw-template Description This command creates a new split horizon group (SHG). Auto-discovered SDP will forward the traffic between the SDPs by default. If mesh kind of behavior is required, split horizon group needs to be configured.
  • Page 284: Table 183 Stp Command

    This command enables the context to configure the Spanning Tree Protocol (STP) parameters for the m-VPLS. Nokia’s STP is simply the Spanning Tree Protocol (STP) with a few modifications to better suit the operational characteristics of VPLS services. The most evident change is to the root bridge election.
  • Page 285: Table 186 Forward-Delay Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context configure>service>vpls>sap>stp Description This command configures the SAP as an edge or non-edge port. If auto-edge is enabled for the SAP, this value will be used only as the initial value. Note: The function of the edge-port command is similar to the rapid-start command.
  • Page 286: Table 187 Hello-Time Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.3.5 hello-time Table 187 hello-time command Item Description Syntax hello-time hello-time no hello-time Context configure>service>vpls>stp Description This command configures the Spanning Tree Protocol (STP) hello time for the m-VPLS. The hello-time parameter defines the default timer value that controls the sending interval between BPDU configuration messages by this bridge, on ports where this bridge assumes the designated role.
  • Page 287: Table 189 Link-Type Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.3.7 link-type Table 189 link-type command Item Description Syntax link-type {pt-pt | shared} no link-type Context configure>service>vpls>sap>stp Description This command instructs STP on the maximum number of bridges behind this SAP. If there is only a single bridge, transitioning to forwarding state will be based on handshaking (fast transitions).
  • Page 288: Table 192 Mst-Port-Priority Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This commands specifies path-cost within a given instance, expressing probability that a given port will be put into the forwarding state in case a loop occurs (the highest value expresses lowest priority).
  • Page 289: Table 194 Mode Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This commands specifies the port priority within a given instance, expressing probability that a given port will be put into the forwarding state if a loop occurs. The no form of this command sets port-priority to its default value.
  • Page 290: Table 196 Mst-Priority Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vpls>stp Description This command creates the context to configure MST instance (MSTI) related parameters. Up to 16 instances will be supported by MSTP. The instance 0 is mandatory by protocol and therefore, it cannot be created by the CLI.
  • Page 291: Table 198 Mst-Max-Hops Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context configure>service>vpls>stp>mst-instance Description This command specifies a range of VLANs associated with a certain MST-instance. This range applies to all SAPs of the m-VPLS. Every VLAN range that is not assigned within any of the created mst-instance is automatically assigned to mst-instance 0.
  • Page 292: Table 199 Mst-Name Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.3.17 mst-name Table 199 mst-name command Item Description Syntax mst-name region-name no mst-name Context configure>service>vpls>stp Description This command defines an MST region name. Two bridges are considered as a part of the same MST region as soon as their configuration of the MST region name, the MST-revision and VLAN-to-instance assignment is identical.
  • Page 293: Table 202 Port-Num Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context configure>service>vpls>sap>stp Description This command configures the Spanning Tree Protocol (STP) path cost for the SAP. The SAP path cost is used by STP to calculate the path cost to the root bridge. The path cost in BPDUs received on the root port is incremented with the configured path cost for that SAP.
  • Page 294: Table 204 Priority Command

    Description This command configures the Nokia Spanning Tree Protocol (STP) priority for the SAP. STP priority is a configurable parameter associated with an SAP. When configuration BPDUs are received, the priority is used in some circumstances as a tie breaking mechanism to determine whether the SAP will be designated or blocked.
  • Page 295: Table 205 Rapid-Start Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.3.23 rapid-start Table 205 rapid-start command Item Description Syntax [no] rapid-start Context configure>service>vpls>sap>stp Description This command enables or disables a rapid start. Default no rapid-start 5.16.3.24 root-guard Table 206 root-guard command Item...
  • Page 296 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command creates a Service Access Point (SAP) within an m-VPLS or v-VPLS service. An SAP is a combination of port and encapsulation parameters which identifies the SAP on the interface and within the ISAM.
  • Page 297: Table 208 Sap Parameters

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag | *} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
  • Page 298: Table 209 Enable-Stats Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.4.2 enable-stats Table 209 enable-stats command Item Description Syntax enable-stats no enable-stats Context configure>service>vpls configure>service>vpls>sap Description This command enables statistics/PM collection for the SAP. 5.16.4.3 restricted-tagging Table 210 restricted-tagging command Item Description...
  • Page 299: Table 212 Eth-Cfm Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description This command creates a local static MAC entry in the v-VPLS forwarding database (FDB) associated with the SAP. In a v-VPLS service, MAC addresses are associated with an SAP or with a Service Distribution Point (SDP).
  • Page 300: Table 213 Mep Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.4.6 Table 213 mep command Item Description Syntax mep mep-id domain md-index association ma-index [direction {up | down}] mep mep-id domain md-indexassociation ma-index Context configure>service>vpls>sap>eth-cfm configure>service>vpls>mesh-sdp>eth-cfm configure>service>vpls>spoke-sdp>eth-cfm configure>eth-ring>path>eth-cfm Description This command enables the Configuration of a Ethernet CFM Maintenance Endpoint...
  • Page 301: Table 215 Ccm-Ltm-Priority Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.4.8 ccm-ltm-priority Table 215 ccm-ltm-priority command Item Description Syntax ccm-ltm-priority priority no ccm-ltm-priority Context configure>service>vpls>sap>eth-cfm>mep configure>service>vpls>mesh-sdp>eth-cfm>mep configure>service>vpls>spoke-sdp>eth-cfm>mep configure>eth-ring>path>eth-cfm>mep Description This command enables configuration of priority for CCM and LTM messages Default Parameters priority - Priority of the CCM/LTM Message...
  • Page 302: Table 217 Mac-Address Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.4.10 mac-address Table 217 mac-address command Item Description Syntax mac-address mac-address no mac-address Context configure>service>vpls>sap>eth-cfm>mep configure>service>vpls>mesh-sdp>eth-cfm>mep configure>service>vpls>spoke-sdp>eth-cfm>mep configure>eth-ring>path>eth-cfm>mep Description This command enables configuration of the MAC Address for the MEP Parameters mac-address - The MAC address of the MEP in xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx format Value: xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx...
  • Page 303: Table 219 Y1731Pm-Enable Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.5 VPLS SAP Filter and QoS Policy Commands 5.16.5.1 y1731pm-enable Table 219 y1731pm-enable command Item Description Syntax [no] y1731pm-enable Context configure>service>vpls>sap>eth-cfm>mep Description This command enables, disables, transmit s, and receives Y1731 PM PDUs. Default no y1731pm-enable 5.16.5.2...
  • Page 304: Table 222 Egress Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command enables the context to configure egress SAP filter policies. If no egress filter is defined, no filtering is performed. (2 of 2) 5.16.5.4 egress Table 222...
  • Page 305: Table 225 Lag-Link-Map-Profile Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.5.7 lag-link-map-profile Table 225 lag-link-map-profile command Item Description Syntax no lag-link-map-profile [link-map-profile-id] Context configure>service>vpls>sap Description This command associates link-map-profile in the lag with the SAP, using the lag-link-map-profile command.
  • Page 306: Table 228 Qos Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command associates an IP filter policy or MAC filter policy with an ingress or egress Service Access Point (SAP) or IP interface. Filter policies control the forwarding and dropping of packets based on IP or MAC matching criteria.
  • Page 307: Table 229 Rate-Limit Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters policy-id — The ID of the QoS policy. Values: 2 — 65535 (2 of 2) 5.16.5.11 rate-limit Table 229 rate-limit command Item Description Syntax rate-limit cir cir-rate pir pir-rate [cbs cbs-size] [pbs pbs-size] no rate-limit Context...
  • Page 308: Table 231 Rate-Limit-Pbits Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vpls>ingress Description This command defines the aggregate ingress rate limit per VPLS service. It applies to traffic associated to the VPLS service which is ingressing on regular ports (network ports) The committed information rate and the peak information rate are entered Optionally, the committed burst size and the peak burst size may be entered.
  • Page 309: Table 233 Dot1P Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context configure>service>vpls>egress>rate-limit-pbits Description This command defines the aggregate egress rate limit for the v-VPLS service matching the dot1p bits specified through rate-limit-pbits. It applies to traffic associated to the service which is egressing on regular ports (network ports).
  • Page 310: Table 234 Meter-Mode Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.5.16 meter-mode Table 234 meter-mode command Item Description Syntax meter-mode {trtcm | trtcm-modified} no meter-mode Context configure>service>vpls>egress>rate-limit-pbits Description This command defines the two-rate three-color marking meter's algorithm. Parameters trctm - The rate-limiting is compliant as per RFC 2698 trctm-modified - The rate-limiting is compliant as per RFC 4115...
  • Page 311: Table 237 Last-Member-Query-Interval Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context configure>service>vpls>sap>igmp-snooping configure>service>mesh-sdp>igmp-snooping configure>service>spoke-sdp>igmp-snooping configure>service>pw-template>igmp-snooping Description This command enables fast leave. When IGMP fast leave processing is enabled, the ISAM will immediately remove an SAP from the IP multicast group when it detects an IGMP 'leave' on that SAP.
  • Page 312: Table 239 Query-Interval Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>vpls>sap>igmp-snooping configure>service>mesh-sdp>igmp-snooping configure>service>spoke-sdp>igmp-snooping Description This command specifies whether a multicast router is attached behind this SAP. Configuring an SAP as an mrouter-port will have a the following effect: IGMP reports generated by the system as a result of someone joining or leaving a multicast group, will be sent to this SAP.
  • Page 313: Table 240 Query-Response-Interval Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.6.6 query-response-interval Table 240 query-response-interval command Item Description Syntax query-response-interval seconds no query-response-interval Context configure>service>vpls>sap>igmp-snooping Description This command configures the IGMP query response interval. If the send-queries command is enabled, this parameter specifies the maximum response time advertised in IGMPv2/v3 queries.
  • Page 314: Table 242 Report-Src-Ip Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.6.8 report-src-ip Table 242 report-src-ip command Item Description Syntax report-src-ip ip-address no report-src-ip Context configure>service>vpls>igmp-snooping Description This parameter specifies the source IP address used when generating IGMP reports. According the IGMPv3 standard, a zero source address is allowed in sending IGMP reports.
  • Page 315: Table 244 Send-Queries Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.6.10 send-queries Table 244 send-queries command Item Description Syntax [no] send-queries Context configure>service>vpls>sap>igmp-snooping Description This command specifies whether to send IGMP general query messages on the SAP. When send-queries is configured, all type of queries generated ourselves are of the configured version.
  • Page 316: Table 246 Group Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.6.12 group Table 246 group command Item Description Syntax group grp-ip-address [no] group Context configure>service>vpls>igmp-snooping>static configure>service>vpls>sap>igmp-snooping>static configure>service>mesh-sdp>igmp-snooping>static configure>service>spoke-sdp>igmp-snooping>static Description This command adds a static multicast group either as a (*,G) or one or more (S,G) records. Use IGMP static group memberships to test multicast forwarding without a receiver host.
  • Page 317: Table 248 Starg Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters ip-address — Specifies the IPv4 unicast address. (2 of 2) 5.16.6.14 starg Table 248 starg command Item Description Syntax [no] starg Context configure>service>vpls>igmp-snooping>static>group configure>service>vpls>sap>igmp-snooping>static>group configure>service>mesh-sdp>igmp-snooping>static>group configure>service>spoke-sdp>igmp-snooping>static>group Description...
  • Page 318: Table 250 Fdb-Info Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.7 Show Commands 5.16.7.1 fdb-info Table 250 fdb-info command Item Description Syntax fdb-info Context show>service Description Displays global FDB usage information. Table describes the command output fields. Table 251 Show FDB-Info Command Output Fields Label...
  • Page 319: Table 252 Fdb-Mac Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.7.2 fdb-mac Table 252 fdb-mac command Item Description Syntax fdb-mac ieee-address [expiry] Context show>service Description This command displays the FDB entry for a given MAC address. Parameters ieee-address - The 48-bit MAC address for which to display the FDB entry in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers.
  • Page 320: Table 255 Show Service Sap Command Output Fields

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
  • Page 321: Table 256 Id Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.7.4 Table 256 id command Item Description Syntax id service-id Context show>service Description Display information for a particular service-id. Parameters service-id — The unique service identification number that identifies the service in the service domain.
  • Page 322: Table 259 Base Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Last Mgmt Change The date and time of the most recent management-initiated change to this customer. SAP Count The number of SAPs specified for this service. Circuit ID Specifies whether the If Index is inserted in Circuit ID suboption of Option 82.
  • Page 323: Table 261 Fdb Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Label Description Admin State The administrative state of the service. Oper State The operational state of the service. The largest frame size (in octets) that the service can handle. SAP Count The number of SAPs defined on the service.
  • Page 324: Table 262 Show Fdb Command Output Fields

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
  • Page 325: Table 263 Mfib Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.7.8 mfib Table 263 mfib command Item Description Syntax mfib [brief] [ip] mfib group grp-address Context show>service>id Description This command displays the multicast FIB on the v-VPLS service. Parameters brief - Displays a brief output.
  • Page 326: Table 266 Sap Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command displays the MSTP specific configuration data. This command is only valid on a management VPLS. (2 of 2) 5.16.7.10 Table 266 sap command Item Description Syntax...
  • Page 327: Table 267 Show Service-Id Sap Command Output Fields

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
  • Page 328: Table 268 Sap-Stats Command Output Fields

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description The SAP and qtag. Encap The encapsulation type of the SAP. Ethertype Specifies an Ethernet type II Ethertype value. Admin State The administrative state of the SAP. Oper State The operational state of the SAP.
  • Page 329: Table 269 Curr-15Min-Stats Command Output Fields

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Label Description Ingress Packets Number of packets that have been received on this SAP after statistics collection was enabled Ingress Octets Number of bytes that have been received on this SAP after statistics collection was enabled Egress Packets Number of packets that have been transmitted on this SAP after statistics collection...
  • Page 330: Table 271 Prev-15Min-Stats Command Output Fields

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Egress Octets The number of bytes transmitted on this SAP since the beginning of the current day interval elapsed-time The amount of time, measured in seconds, that has elapsed since the beginning of the current day interval Measure-time The amount of time, measured in seconds that statistics for this entry have been...
  • Page 331: Table 273 Stp Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Label Description Measure-time The amount of time, measured in seconds that statistics for this entry have been actually counted for the 1-day interval. This value will be the same as the interval except in a situation where performance monitoring data could not be collected for this SAP for some reason (2 of 2)
  • Page 332 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Root path cost Specifies the cost of the path to the root bridge as seen from this bridge. Root forward delay Specifies how fast the root changes its state when moving toward the forwarding state. Root hello time Specifies the amount of time between the transmission of configuration BPDUs.
  • Page 333: Table 275 Igmp-Snooping Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.8 IGMP Snooping Show Commands 5.16.8.1 igmp-snooping Table 275 igmp-snooping command Item Description Syntax igmp-snooping Context show>service>id Description This command enables the context to display IGMP snooping information. 5.16.8.2 Table 276 all command...
  • Page 334: Table 278 Mrouters Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Num Groups Specifies the actual number of multicast groups that can be joined on this SAP. (2 of 2) 5.16.8.3 mrouters Table 278 mrouters command Item Description Syntax...
  • Page 335: Table 280 Show Port-Db Command Output Fields

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
  • Page 336: Table 281 Querier Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Compatibility mode Specifies the IGMP mode. This is used in order for routers to be compatible with older version routers. IGMPv3 hosts must operate in Version 1 and Version 2 compatibility modes.
  • Page 337: Table 282 Querier Command Output Fields

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Table 282 Querier Command Output Fields Label Description SAP Id Specifies the SAP ID of the service. IP address Specifies the IP address of the querier. Expires The time left, in seconds, that the query will expire.
  • Page 338: Table 284 Static Command Output Fields

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
  • Page 339: Table 286 Statistics Command Output Fields

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Context show>service>id>igmp-snooping Description This command displays IGMP snooping statistics for the v-VPLS service. Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} •...
  • Page 340: Table 287 Id Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description Bad Length number of IGMP messages that have been dropped because bad length Bad IP Checksum number of IGMP messages that have been dropped because bad IP checksum Bad IGMP Checksum number of IGMP messages that have been dropped because bad IGMP checksum Bad Encoding...
  • Page 341: Table 289 Fdb Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Description Clears DHCP statistics for this service. Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} •...
  • Page 342 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters all - Clears all FDB entries. mac ieee-address - Clears only FDB entries in the FDB table with the specified 48-bit MAC address. The MAC address can be expressed in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers.
  • Page 343: Table 290 Sap Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.9.4 Table 290 sap command Item Description Syntax sap sap-id Context clear>service>statistics Description This command displays IGMP snooping statistics for the v-VPLS service. Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} •...
  • Page 344: Table 292 Mesh-Sdp Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.9.6 mesh-sdp Table 292 mesh-sdp command Item Description Syntax mesh-sdp sdp-id:[vc-id] {all | counters} Context clear>service>statistics>id Description This command clears all the statistics associated with the mesh SDP. Parameters sdp-id - The SDP ID for which to clear statistics.
  • Page 345: Table 294 Stp Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.9.8 Table 294 stp command Item Description Syntax Context clear>service>id clear>service>statistics>id Description Clears all spanning tree statistics for the service ID. 5.16.9.9 detected-protocols Table 295 detected-protocols command Item Description Syntax...
  • Page 346: Table 296 Statistics Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters all - Clears all detected protocol statistics. sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} •...
  • Page 347: Table 297 Mesh-Sdp Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service Item Description Parameters all - Clears the statistics for all SAPs. sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} •...
  • Page 348: Table 298 Mesh-Sdp Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sdp-id - The SDP ID for which to clear the ingress VC label. Values: 1...17407 vc-id - The virtual circuit ID on the SDP ID for which to clear the ingress VC label. Values: 1...4294967295 (2 of 2) 5.16.9.12...
  • Page 349: Table 300 Id Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.10 Debug Commands 5.16.10.1 Table 300 id command Item Description Syntax id service-id] Context debug>service Description This command debugs commands for a specific service. Parameters service-id - The ID that uniquely identifies a service. 5.16.10.2 igmp-snooping Table 301...
  • Page 350: Table 303 Mac Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.10.4 Table 303 mac command Item Description Syntax [no]mac ieee-address Context debug>service>id>igmp Description This command shows IGMP packets for the specified MAC address. The no form of the command disables the MAC debugging. 5.16.10.5 mode Table 304...
  • Page 351: Table 306 All-Events Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.10.7 all-events Table 306 all-events command Item Description Syntax [no] all-events Context debug>service>stp Description This command enables STP debugging for all events. 5.16.10.8 bpdu Table 307 bpdu command Item Description Syntax...
  • Page 352: Table 309 Exception Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 5.16.10.10 exception Table 309 exception command Item Description Syntax [no] exception Context debug>service>stp Description This command enables STP debugging for exceptions. 5.16.10.11 fsm-state-changes Table 310 fsm-state-changes command Item Description Syntax...
  • Page 353: Table 312 Port-Role Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.10.13 port-role Table 312 port-role command Item Description Syntax [no] port-role Context debug>service>stp Description This command enables STP debugging for changes in port roles. 5.16.10.14 port-state Table 313 port-state command Item Description...
  • Page 354: Table 315 Interface Command

    Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>: <nwport-id | ltport-id>...
  • Page 355: Table 316 Mcs Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private LAN Service 5.16.10.17 Table 316 mcs command Item Description Syntax [no] mcs [ip-int-name] Context debug>router>igmp Description This command enables debugging for IGMP MCS. Parameters ip-int-name — Only displays the information associated with the specified IP interface name. 5.16.10.18 misc Table 317...
  • Page 356 Virtual Private LAN Service FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13...
  • Page 357: Internet Enhanced Service

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6 Internet Enhanced Service 6.1 In This Chapter 6.2 IES Services Overview 6.3 IES Features 6.4 Configuring an IES Service with CLI 6.5 Basic Configuration 6.6 Common Configuration Tasks 6.7 Configuring IES Components 6.8 Service Management Tasks 6.9 IES Services CLI Command Reference...
  • Page 358: Ies Features

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.3 IES Features 6.3.1 IP Interfaces IES customer IP interfaces can be configured with most of the same options found on the core IP interfaces. The advanced configuration options supported are: •...
  • Page 359: Configuring An Ies Service With Cli

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service The DHCPv4 and DHCPv6 lease state is synchronized to the standby network card. For DHCPv6, the managed neighbor cache and managed routes are also synchronized to the standby network card. If the active network card fails, all DHCP hosts stay active without service interruption.
  • Page 360: Common Configuration Tasks

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide exit no shutdown ---------------------------------------------- *A:ALA-48>configure>service# 6.6 Common Configuration Tasks This section provides a brief overview of the tasks that must be performed to configure IES services and provides the CLI commands. 1 Associate an IES service with a customer ID.
  • Page 361: Configuring Ies Interface Parameters

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.7.2 Configuring IES Interface Parameters The following example displays an IES configuration with interface parameters: A:ALA-48>configure>service>ies>interface# info ---------------------------------------------- address 10.1.1.1/24 sap nt:sfp:1:50 create ingress exit egress exit exit ---------------------------------------------- A:ALA-48>configure>service>ies>interface# 6.7.3...
  • Page 362: Modifying Ies Service Parameters

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.8.1 Modifying IES Service Parameters Existing IES service parameters in the CLI or NMS can be modified, added, removed, enabled or disabled. The changes are applied immediately to all services when the charges are applied.
  • Page 363: Re-Enabling An Ies Service

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.8.4 Re-enabling an IES Service To re-enable an IES service that was shut down: configure>service> ies service-id [no] shutdown Example: configure>service# ies 2000 configure>service>ies# no shutdown configure>service>ies# exit 6.9 IES Services CLI Command Reference 6.9.1 Command Hierarchies...
  • Page 364 Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide — no arp-timeout — transmit-interval [receive receive-interval] [multiplier multiplier] — — delayed-enable [seconds] — no delayed-enable — description description-string — no description — dhcp — description description-string — no description —...
  • Page 365: Interface Sap Commands

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.9.1.3 Interface SAP Commands configure — service — service-id [customer customer-id] — [no] interface ip-int-name — [no] sap-id — description description-string — no description — egress — filter {ip ip-filter-id | ipv6 ipv6-filter-id} —...
  • Page 366: Table 319 Shutdown Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10 IES Service CLI Configuration Commands The following commands are described: • Generic Commands • IES Global Commands • IES QoS Policy Commands • IES Interface Commands • IES Interface DHCP Commands •...
  • Page 367: Table 320 Description Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Special Cases IES — The default administrative status of an IES service is down. While the service is down, all its associated virtual router interfaces will be operationally down. The administrative state of the service is not reflected in the administrative state of the virtual router interface.
  • Page 368: Table 322 Sgt-Qos Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>ies configure>service>ies>interface Description This command creates a text description stored in the configuration file for a configuration context. The description command associates a text string with a configuration context to help identify the content in the configuration file.
  • Page 369: Table 324 Egress Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Context configure>service Description This command creates or edits an IES service instance. The ies command is used to create or maintain an Internet Enhanced Service (IES). If the service-id does not exist, a context for the service is created.
  • Page 370: Table 325 Ingress Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>ies Description This command enables the context to configure egress rate-limiting policies. If no egress filter is defined, no rate-limiting is performed. (2 of 2) 6.10.3.2 ingress Table 325...
  • Page 371: Table 327 Rate-Limit Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.3.4 rate-limit Table 327 rate-limit command Item Description Syntax rate-limit cir cir-rate pir pir-rate [cbs cbs-size] [pbs pbs-size] no rate-limit Context configure>service>ies>egress Description This command defines the aggregate egress rate limit per IES service. It applies to traffic associated to the IES service which is egressing on regular ports (network ports) The committed information rate and the peak information rate are entered...
  • Page 372: Table 329 Interface Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters cir cir-rate — The committed information rate expressed in kbps. Values: up to 100 Gbps pir pir-rate — The peak information rate expressed in kbps. Values: up to 100 Gbps cbs cbs-size —...
  • Page 373: Table 330 Address Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Description This command creates a logical IP routing interface for an Internet Enhanced Service (IES). Once created, attributes like an IP address and service access point (SAP) can be associated with the IP interface.
  • Page 374: Table 331 Operational State

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Description This command assigns an IP address, IP subnet, and broadcast address format to an IES IP router interface. Only one IP address can be associated with an IP interface. An IP address must be assigned to each IES IP interface.
  • Page 375: Table 332 Arp-Timeout Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.4.3 arp-timeout Table 332 arp-timeout command Item Description Syntax arp-timeout seconds no arp-timeout Context configure>service>ies>interface Description This command configures the minimum time, in seconds, an ARP entry learned on the IP interface is stored in the ARP table.
  • Page 376: Table 334 Delayed-Enable Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters transmit-interval - Sets the transmit interval, in milliseconds, for the BFD session. Values 100 — 100000 Default: 100 receive receive-interval - Sets the receive interval, in milliseconds, for the BFD session. Values 100 —...
  • Page 377: Table 336 Local-Proxy-Arp Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Description This command configures the IP maximum transmit unit (packet) for the interface. If the configured value is less than or equal to 9194, it applies to both the control plane and the data plan (fast path).
  • Page 378: Table 338 Protect Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.4.9 protected Table 338 protect command Item Description Syntax [no] protected Context configure>service>ies>interface Description This command selects the IES interface configuration and the associated configuration for the interface that enables the interface to be operational (manage access from remote clients). The command stores the configuration as part of protected configuration when the user issues the admin software-management IHub database oam-save-protected command.
  • Page 379 FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Parameters ip-address — The IP address of the IP interface. The ip-address portion of the address command specifies the IP host address that will be used by the IP interface within the subnet. This address must be unique within the subnet and specified in dotted decimal notation.
  • Page 380: Table 340 Dhcp Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.5 IES Interface DHCP Commands 6.10.5.1 dhcp Table 340 dhcp command Item Description Syntax dhcp Context configure>service>ies>interface Description This command enables the context to configure DHCP parameters. 6.10.5.2 gi-address Table 341 gi-address command...
  • Page 381: Table 342 Lease-Query Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.5.3 lease-query Table 342 lease-query command Item Description Syntax lease-query {enable | disable}] no lease-query Context configure>service>ies>interface>dhcp Description Enables lease-query functionality in this interface. Enable will process broadcast LQ and Disable will discard broadcast LQ, but irrespective of Enable/Disable, unicast LQ will be forwarded.
  • Page 382: Table 345 Server Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>ies>interface>dhcp>option Description This command configures the Relay Agent Information Option (Option 82) processing. The no form of this command returns the system to the default value. Default The default is to keep the existing information intact.
  • Page 383: Table 347 Rid-Check-Disable Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Description This command enables dynamic host lease state management for IES IP interfaces. Lease state information is extracted from snooped or relayed DHCP ACK messages to populate lease state table entries for the IP interface.
  • Page 384: Table 349 Mask-Reply Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Context configure>service>ies>interface Description This command enables the context to configure Internet Control Message Protocol (ICMP) parameters on an IES service (2 of 2) 6.10.6.2 mask-reply Table 349 mask-reply command Item Description...
  • Page 385: Table 351 Unreachables Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Parameters number — The maximum number of ICMP TTL expired messages to send, expressed as a decimal integer. This parameter must be specified with the seconds parameter. Values: 10 —...
  • Page 386: Table 352 Ipv6 Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.7 IPv6 Commands 6.10.7.1 ipv6 Table 352 ipv6 command Item Description Syntax [no] ipv6 Context configure>service>ies>interface Description This command configures an IPv6 interface. When IPv6 routing is configured on the IHub and an Note —...
  • Page 387: Table 354 Dhcp6-Relay Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Parameters ipv6-address/prefix-length — Specifies the IPv6 address on the interface. Values: ipv6-address/prefix: ipv6-address x:x:x:x:x:x:x:x (eight 16-bit pieces) x:x:x:x:x:x:d.d.d.d x [0 — FFFF]H d [0 — 255]D prefix-length 1 —...
  • Page 388: Table 356 Lease-Populate Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.7.5 lease-populate Table 356 lease-populate command Item Description Syntax lease-populate [nbr-of-leases] no lease-populate Context configure>service>ies>interface>ipv6>dhcp6-relay Description This command specifies specify the maximum number of leases maintained in the lease state database.
  • Page 389: Table 358 Interface-Id Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.7.7 interface-id Table 358 interface-id command Item Description Syntax interface-id [ascii-tuple | ifindex | sap-id | string <string>] no interface-id Context configure>service>ies>interface>ipv6>dhcp6-relay>option Description The operator can configure the interface ID option. When the interface ID option is enabled all the relay-forward messages will include interface-id option.
  • Page 390: Table 360 Server Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.7.9 server Table 360 server command Item Description Syntax server ipv6-address [ipv6-address...(up to 8 maximum)] Context configure>service>ies>interface>ipv6>dhcp6-relay Description This command specifies a list of servers where requests will be forwarded. The list of servers can be entered as IP addresses.
  • Page 391: Table 363 Packet-Too-Big Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.7.12 packet-too-big Table 363 packet-too-big command Item Description Syntax packet-too-big [number seconds] no packet-too-big Context configure>service>ies>interface>ipv6>icmp6 Description This command configures the rate for ICMP packet-too-big messages issued on the router interface.
  • Page 392: Table 365 Time-Exceeded Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters number — The maximum number of ICMP param-problem messages to send. This parameter must be specified with the seconds parameter. Values: 10 — 1000 seconds — The time frame in seconds used to limit the number of ICMP param-problem messages that can be issued.
  • Page 393: Table 367 Local-Proxy-Nd Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Description This command configures the rate for ICMP host and network destination unreachable messages issued on the router interface. The unreachables command enables the generation of ICMP destination unreachables on the router interface.
  • Page 394: Table 368 Prefix-Stability Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.7.17 prefix-stability Table 368 prefix-stability command Item Description Syntax prefix-stability {enable | disable} no prefix-stability Context configure>service>ies>interface>dhcp6-relay Description Enables prefix-stability functionality in this interface. Default The default value is Disabled. Parameters {Enable} —...
  • Page 395: Table 370 Sap Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.8 IES SAP Filter and QoS Policy Commands 6.10.8.1 Table 370 sap command Item Description Syntax sap sap-id no sap sap-id Context configure>service>ies>interface Description This command creates a Service Access Point (SAP) within a service. A SAP is a combination of port and encapsulation parameters which identifies the service access point on the interface and within the ISAM.
  • Page 396: Table 371 Port And Encapsulation Type Values

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: {port-id | lag-id}:{vlanid | no-tag} • port-id Specifies the physical port ID in the following format: <port-id>...
  • Page 397: Table 372 Filter Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.8.2 filter Table 372 filter command Item Description Syntax filter { ip ip-filter-id| ipv6 ipv6-filter-id} no filter [ip ip-filter-id] [ipv6 ipv6-filter-id] Context configure>service>ies>interface>sap>egress configure>service>ies>interface>sap>ingress Description This command associates a filter policy with an ingress or egress Service Access Point (SAP). Filter policies control the forwarding and dropping of packets based on the matching criteria.
  • Page 398: Table 374 Ingress Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.8.4 ingress Table 374 ingress command Item Description Syntax ingress Context configure>service>ies>interface>sap Description This command enables the context to configure ingress SAP filter policies. If no ingress filter is defined, no filtering is performed 6.10.9 Show Commands 6.10.9.1...
  • Page 399: Table 377 Sap-Using Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description Specifies the SAP assigned to the service. (2 of 2) 6.10.9.2 sap-using Table 377 sap-using command Item Description Syntax sap-using [sap sap-id] sap-using interface [ip-address | ip-int-name] Context show>service Description...
  • Page 400: Table 378 Show Service Arp Output

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
  • Page 401: Table 379 Id Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.9.3 Table 379 id command Item Description Syntax id service-id {all | arp | base | interface | sap} Context show>service Description Display information for a particular service ID. Parameters service-id —...
  • Page 402 Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Label Description SAP Count The number of SAPs specified for this service. QoS Rate-Limit Pbits The set of 802.1p bits for which the rate-limiter will be applied Committed rate (kbps) The committed rate in kbps Committed burst size (kB) The committed burst size in kb...
  • Page 403: Table 382 Arp Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description Low priority offered The packets or octets count of the low priority traffic. Low priority dropped The number of low priority traffic packets/octets dropped. In profile forwarded The number of in-profile packets or octets (rate below CIR) forwarded.
  • Page 404: Table 383 Show Service Sap Output

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters ip-address — Displays only ARP entries in the ARP table with the specified IP address. Default: All IP addresses. mac ieee-address — Displays only ARP entries in the ARP table with the specified 48-bit MAC address.
  • Page 405: Table 384 Base Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description Expiry The age of the ARP entry. Interface The interface applied to the service. The SAP ID. (2 of 2) 6.10.9.6 base Table 384 base command Item Description Syntax...
  • Page 406: Table 387 Lease-State Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
  • Page 407 FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
  • Page 408: Table 388 Summary Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.9.10 summary Table 388 summary command Item Description Syntax summary Context show>service>id>dhcp Description Displays DHCP configuration summary information. Table describes the command output fields. Table 389 Show DHCP Summary Output Label Description Interface Name...
  • Page 409: Table 391 Summary Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.9.12 summary Table 391 summary command Item Description Syntax summary Context show>service>id>dhcp6 Description Displays DHCP6 configuration summary information. Table describes the command output fields. Table 392 Show DHCP6 Summary Output Label Description Interface Name...
  • Page 410: Table 394 Show Dhcp Lease State Output

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters interface interface-name - Displays DHCP lease state related information for the specified interface. ipv6-address ipv6-prefix[/prefix-length] - Displays DHCP lease state related information for the specified IPv6 address. mac ieee-address - Displays DHCP lease state related information for the specified MAC address.
  • Page 411: Table 396 Statistics Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description ServerLeaseRenew Time stamp indicates when client last renewed to the server ServerLeaseEnd Time stamp indicates when lease expires (2 of 2) 6.10.9.14 statistics Table 396 statistics command Item Description Syntax...
  • Page 412: Table 399 Show Service Id Interface Output

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters ip-address — The IP address of the interface for which to display information. Values: ipv4-address: a.b.c.d (host bits must be 0) ip-int-name — Specifies the IP interface name for which to display information. Values: 32 characters maximum family —...
  • Page 413: Table 400 Sap Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description DHCP Details Description Provides the description of the IES interface. Admin state Specifies the administrative state for DHCP relay. Lease Query Specifies whether the Lease Query is enabled or disabled. Servers Specifies the configured DHCP servers.
  • Page 414: Table 401 Show Service Sap Output

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide Item Description Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag • port-id Specifies the physical port ID in the following format: <port-id>...
  • Page 415 FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Label Description Flags Specifies the conditions that affect the operating status of this SAP. Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, PortMTUTooSmall, L2OperDown, SapIngressQoSMismatch, SapEgressQoSMismatch, RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, NoSapIpipeCeIpAddr, TodResourceUnavail, TodMssResourceUnavail, SapParamMismatch, CemSapNoEcidOrMacAddr, StandByForMcRing, ServiceMTUTooSmall, SapIngressNamedPoolMismatch, SapEgressNamedPoolMismatch, NoSapEpipeRingNode, mcStandby (22),...
  • Page 416: Table 402 Id Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.10 Clear Commands 6.10.10.1 Table 402 id command Item Description Syntax id service-id Context clear>service clear>service>statistics Description This command clears parameters for a specific service. Parameters service-id — The ID that uniquely identifies the service to clear. 6.10.10.2 interface Table 403...
  • Page 417: Table 405 Stp Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service Item Description Description This command clears FDB entries for the service. Parameters all — Clears all FDB entries. mac ieee-address — Clears only FDB entries in the FDB table with the specified 48-bit MAC address.
  • Page 418: Table 406 Statistics Command

    Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 6.10.10.5 statistics Table 406 statistics command Item Description Syntax statistics [sap sap-id | interface ip-address | ip-int-name] Context clear>service>id>dhcp Description This command clears DHCP statistics. Parameters sap sap-id — Specifies the physical port identifier portion of the SAP definition. Values: [port-id | lag-id] vlanid | no-tag * •...
  • Page 419: Table 407 Lease-State Command

    FD 100/320Gbps NT and FX NT IHub Services Guide Internet Enhanced Service 6.10.10.6 lease-state Table 407 lease-state command Item Description Syntax lease-state ipv6-address ipv6-prefix[/prefix-length] lease-state mac ieee-address lease-state sap sap-id Context clear>service>dhcp6 Description Clears lease state statistics for DHCP6. Parameters ip-prefix/prefix-length - The destination address of the aggregate route.
  • Page 420 Internet Enhanced Service FD 100/320Gbps NT and FX NT IHub Services Guide 3HH-11985-AAAA-TQZZA Issue: 13...
  • Page 421: Virtual Private Routed Network Service

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7 Virtual Private Routed Network Service 7.1 In This Chapter 7.2 VPRN Service Overview 7.3 VPRN Features 7.4 Configuring a VPRN Service with CLI 7.5 Basic Configuration 7.6 Common Configuration Tasks 7.7 Configuring VPRN Components 7.8 Service Management Tasks...
  • Page 422: Figure 33 Virtual Private Routed Network

    Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide The ISAM uses an IGP (RIP, OSPF, ISIS) to exchange the routes of a particular CE router with the PE routers that are attached to that ISAM. This is done in a way which ensures that routes from different VPNs remain distinct and separate, even if two VPNs have an overlapping address space.
  • Page 423: Route Redistribution

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.2.1.1 Route Redistribution Routing information learned from the ISAM-to-PE routing protocols and configured static routes should be injected in the associated local VPN routing/forwarding (VRF). In the case of dynamic routing protocols, there may be protocol specific route policies that modify or reject certain routes before they are injected into the local VRF.
  • Page 424: Figure 34 Conceptual Diagram

    Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide Figure 34 Conceptual Diagram IPD L3 VPRN VLANs must have system global scope IPD L2 v-VPLS v-VPLS For the MTU size of an IP interface, a fixed value of Note 1 —...
  • Page 425: Basic Configuration

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service Topics in this section include: • Basic Configuration • Common Configuration Tasks • Configuring VPRN Components • Creating a VPRN Service • Configuring Global VPRN Parameters •...
  • Page 426: Common Configuration Tasks

    Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide exit vrrp 1 exit exit static-route 6.5.0.0/24 next-hop 10.1.1.2 router-id 10.0.0.1 group "to-cel" export "vprnBgpExpPolCust1" peer-as 65101 neighbor 10.1.1.2 exit exit exit static exit bsr-candidate shutdown exit shutdown exit...
  • Page 427: Configuring Vprn Components

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7 Define BGP parameters (optional). • BGP must be enabled in the configure>router>bgp context. 8 Define RIP parameters (optional). • RIP must be enabled in the configure>router>rip context. 9 Enable the service.
  • Page 428: Configuring Router Interfaces

    Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide vprn 1 customer 1 create vrf-import "vrfImpPolCust1" vrf-export "vrfExpPolCust1" autonomous-system 10000 route-distinguisher 10001:1 exit no shutdown exit ---------------------------------------------- *A:ALA-1>configure>service# 7.7.3 Configuring Router Interfaces Refer to the FD 100/320Gbps NT and FX NT IHub Router Configuration and Protocols Guide for command descriptions and syntax information to configure router interfaces.
  • Page 429 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service In order to enable a VPRN BGP instance, the BGP protocol must be enabled in the configure>router>bgp context on each participating ISAM router. Careful planning is essential to implement commands Note —...
  • Page 430: Configuring Vprn Bgp Group And Neighbor Parameters

    Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide 7.7.4.1 Configuring VPRN BGP Group and Neighbor Parameters A group is a collection of related VPRN BGP peers. The group name should be a descriptive name for the group. Follow your group, name, and ID naming conventions for consistency and to help when troubleshooting faults.
  • Page 431: Vprn Rip Cli Syntax

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service In order to enable a VPRN RIP instance, the RIP protocol must be enabled in the configure>router> rip context on each participating ISAM. VPRN RIP is administratively enabled upon creation.
  • Page 432: Configuring Vprn Protocols - Ospf

    Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide ecmp 2 autonomous-system 10000 route-distinguisher 10001:1 vrf-target target:10001:1 interface "to-ce1" create address 11.1.0.1/24 sap nt:sfp:1:1 create ingress scheduler-policy "SLA2" qos 100 exit egress scheduler-policy "SLA1" qos 1010 filter ip 6 exit exit...
  • Page 433: Vprn Ospf Cli Syntax

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service 7.7.6.1 VPRN OSPF CLI Syntax Refer to “OSPF Configuration Commands” for CLI syntax to configure VPRN parameters. The following example displays the VPRN OSPF configuration shown above: A:debby-sim1>configure>service# info ---------------------------------------------- vprn 2 customer 1 create...
  • Page 434: Configuring A Vprn Interface - Sap

    Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide static-route 6.5.0.0/24 next-hop 10.1.1.2 no shutdown exit ---------------------------------------------- *A:ALA-1>configure>service# 7.7.8 Configuring a VPRN Interface - SAP To associate an IP interface to one or more network ports and/or access/hybrid ports, at least two v-VPLS must be configured, one with a SAP on each associated network/hybrid port, and one with the access/hybrid ports.
  • Page 435: Deleting A Vprn Service

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service maximum-routes 2000 autonomous-system 10000 route-distinguisher 10001:1 interface "to-ce1" create address 10.1.1.1/24 sap nt:sfp:1:1 create exit exit static-route 6.5.0.0/24 next-hop 10.1.1.2 router-id 10.0.0.1 group "to-ce1" export "vprnBgpExpPolCust1" peer-as 65101 neighbor 10.1.1.2 exit...
  • Page 436: Re-Enabling A Vprn Service

    Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide configure>service# vprn 1 configure>service>vprn# shutdown configure>service>vprn# exit *A:ALA-1>configure>service# info ---------------------------------------------- vprn 1 customer 1 create shutdown vrf-import "vrfImpPolCust1" vrf-export "vrfExpPolCust1" ecmp 2 autonomous-system 10000 route-distinguisher 10001:1 auto-bind ldp vrf-target target:10001:1 interface "to-ce1"...
  • Page 437: Vprn Services Cli Command Reference

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service configure>service# vprn service-id [customer customer-id] no shutdown 7.9 VPRN Services CLI Command Reference 7.9.1 Command Hierarchies This section shows the following command hierarchies: • VPRN Service Configuration Commands •...
  • Page 438: Interface Commands

    Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide — [no] on-link — [no] preferred-lifetime {seconds | infinite} — [no] valid-lifetime {seconds | infinite} — [no] reachable-time milli-seconds — [no] retransmit-time milli- seconds — [no] router-lifetime seconds —...
  • Page 439: Interface Sap Commands

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service — prefix-stability {enable | disable} — no prefix-stability — prfx-hlddwn-time <seconds> — no prfx-hlddwn-time — server ipv6-address [ipv6-address...(up to 8 maximum)] — no server [ipv6-address...(up to 8 maximum)] —...
  • Page 440 Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide — service — vprn service-id [customer customer-id] — [no] — [no] advertise-inactive — [no] aggregator-id-zero — always-compare-med {zero | infinity} — no always-compare-med — [no] as-path-ignore —...
  • Page 441 FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service — no family — hold-time seconds — no hold-time — import policy-name [policy-name...(up to 5 max)] — no import — keepalive seconds — no keepalive — local-address ip-address —...
  • Page 442: Ospf Configuration Commands

    Virtual Private Routed Network Service FD 100/320Gbps NT and FX NT IHub Services Guide — min-route-advertisement seconds — no min-route-advertisement — multihop ttl-value — no multihop — [no] next-hop-self — [no] passive — peer-as as-number — no peer-as — preference preference —...
  • Page 443: Rip Configuration Commands

    FD 100/320Gbps NT and FX NT IHub Services Guide Virtual Private Routed Network Service — [no] asbr — [no] compatible-rfc1583 — export policy-name [ policy-name...(up to 5 max)] — no export — external-db-overflow limit seconds — no external-db-overflow — external-preference preference —...
  • Page 444: Show Commands

    Virtual Private Routed Network Serv