Cisco Asr 1000 Series Aggregation Services Routers Sip And Spa Software Configuration Guide, Cisco Ios - Cisco ASR 1000 Series Software Configuration Manual

Aggregation services routers sip and spa, cisco ios xe everest 16.5
Table of Contents

Advertisement

Overview of the Serial SPAs
Bandwidth limit is 44210, DSU mode 0, Cable length is 10 feet
rx FEBE since last clear counter 0, since reset 0
Data in current interval (820 seconds elapsed):
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation
0 P-bit Err Secs, 0 P-bit Sev Err Secs
0 Sev Err Framing Secs, 0 Unavailable Secs
0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs
0 Severely Errored Line Secs
0 Far-End Errored Secs, 0 Far-End Severely Errored Secs
0 CP-bit Far-end Unavailable Secs
0 Near-end path failures, 0 Far-end path failures
0 Far-end code violations, 0 FERF Defect Secs
0 AIS Defect Secs, 0 LOS Defect Secs
Data in Interval 1:
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation
0 P-bit Err Secs, 0 P-bit Sev Err Secs
0 Sev Err Framing Secs, 0 Unavailable Secs
The following example shows an output of the show controllers serial command on a Cisco ASR 1000 Series
Router with a 2-Port Clear-Channel T3/E3 SPA installed in slot 2:
Router# show controllers serial 2/2/0
Serial1/0/1 - (SPA-8XT3/E3) is up
Current mode is T3
Framing is c-bit, Clock Source is Line
Bandwidth limit is 44210, DSU mode 0, Cable length is 10 feet
rx FEBE since last clear counter 0, since reset 0
Tabular MIB:
INTERVAL
01:30-01:36
01:15-01:30
Total
No alarms detected.
No FEAC code is being received
MDL transmission is disabled
The following example shows an output of the show controllers command on a Cisco ASR 1000 Series
Router with an 8-Port Channelized T1/E1 SPA installed in slot 0:
Router# show controllers e1 0/3/0 brief
E1 0/3/0 is up.
Applique type is SPA-8XCHT1/E1
No alarms detected.
alarm-trigger is not set
Framing is crc4, Line Code is HDB3, Clock Source is Line.
Data in current interval (571 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
The following example shows an output of the show controllers command on a Cisco ASR 1000 Series
Router with a 4-Port Channelized T3 SPA installed in slot 2:
Router# show controllers t3
T3 2/0/0 is up.
Hardware is SPA-2XCT3/DS0
IO FPGA version: 2.7, HDLC Framer version: 0
T3/T1 Framer(1) version: 2
SUBRATE FPGA version: 1.4
HDLC controller available FIFO buffers 4084
Applique type is Channelized T3/T1
No alarms detected.
MDL transmission is disabled
FEAC code received: No code is being received
Framing is C-BIT Parity, Line Code is B3ZS, Cablelength is 224
OL-14127-17
LCV
PCV
CCV
0
0
0
1
0
0
1
0
0
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS XE
Examples of the show controllers Command
PES
PSES
SEFS
UAS
0
0
0
0
0
0
0
1
0
0
0
1
LES
CES
CSES
0
14
14
1
0
0
1
0
0
Everest 16.5
221

Advertisement

Table of Contents
loading

Table of Contents