Cisco ASR 1000 Series Quick Start Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. ASR 1000 Series
  6. Quick start manual

Cisco ASR 1000 Series Quick Start Manual

Aggregation services routers
Hide thumbs Also See for ASR 1000 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Q
S
G
UICK
TART
Cisco ASR 1002-X Router
1
Documentation and Resources
2
Prepare for Installation
3
Rack-Mount the Router
4
Connect the Router to the Network
5
Start the System
6
Configuring the Router
7
After Installation
UIDE

Advertisement

Table of Contents
loading

Related Manuals for Cisco ASR 1000 Series

Summary of Contents for Cisco ASR 1000 Series

  • Page 1 UICK TART UIDE Cisco ASR 1002-X Router Documentation and Resources Prepare for Installation Rack-Mount the Router Connect the Router to the Network Start the System Configuring the Router After Installation...

  • Page 2: Document Revision History

    Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version...

  • Page 3: Prepare For Installation

    Only trained and qualified personnel should install, replace, or service this equipment. Statement 1030 Caution The eUSB panel door on the side of the Cisco ASR 1002-X Router must not be opened. If there is a problem with eUSB flash card, the chassis should be returned.

  • Page 4: Prepare For Rack-Mount Installation

    This section provides information about rack-mounting the router. Attach the Rack-Mount Brackets—Chassis Front-Mounted To attach the rack-mount brackets on a Cisco ASR 1002-X Router for a front rack-mount configuration, follow these steps: Step 1 Locate the threaded holes in the front sides of the chassis.

  • Page 5: Two-Post Rack Installation

    • Never attempt to lift an object that might be too heavy for you to lift by yourself. We recommend that at least two people install the router in an equipment rack. • Ensure that the floor under the rack supporting the Cisco 1000 Series Routers is capable of supporting the combined weight of the rack and all the other installed equipment.
  • Page 6 The cable-management bracket for the Cisco ASR 1002-X Router contain one independent cable-management U type device with two screws for each bracket, and provides cable dressing for each card module slot. In the ASR 1000 Series SPA interface, these brackets work in tandem with the SPA product feature cable-management device to allow the installation and removal of adjacent cards without the need to remove cables.

  • Page 7: Chassis Ground Connection Installation

    Before you connect the power or turn on the power to your router, you must provide an adequate chassis ground (earth) connection for the Cisco ASR 1002-X Router. The chassis ground lugs (two) and the respective screws (four) are provided in the accessory kit that is shipped with your Cisco ASR 1002-X Router.
  • Page 8 Figure 4 Cisco ASR 1002-X Router Ground Connector Location — — Cisco ASR 1002-X Router ground stud location. Perform the following steps to install chassis ground connection: Use the wire stripper to strip one end of the AWG #6 wire approximately 0.75 inches (19.05 mm).

  • Page 9: Console And Auxiliary Port Cable Connections

    Console and Auxiliary Port Cable Connections This section describes how to attach a cable to the console port or auxiliary port on the Cisco ASR 1002-X Router. The Cisco ASR 1002-X Router has two RJ-45 ports for terminal connection. A console port, which can be utilized for terminal connections...
  • Page 10 Step 3 After you establish normal router operation, you can disconnect the terminal. For information about console port and auxiliary port pinouts, see the Cisco ASR 1002-X Router specifications in the Note Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation Guide.

  • Page 11: Connect The Shared Port Adapter Cables

    Step 3 Connect the Shared Port Adapter Cables The instructions for connecting the cables for the shared port adapters installed in the Cisco ASR 1002-X Router are contained in the Cisco ASR 1000 Series Aggregation Services Routers SPA and SIP Hardware Installation Guide.

  • Page 12: Start The System

    It might be necessary to bundle longer cables to avoid tangling them. Do this at the cable-management bracket or at the rack, but leave enough slack in the cables to remove a Cisco ASR 1000-ESP5 and change cables as required. Also, do not block the power supply air vents with cables.
  • Page 13 AC power supplies for the Cisco Aggregation Services Routers: 120 VAC, 20A U.S. maximum. DC power supplies for the Cisco ASR 1006 Router: 50A U.S. maximum; Cisco ASR 1004 Router: 40A U.S. maximum: Cisco ASR 1002-X Router: 30A (–48V) U.S. and 40A (+24V) U.S. maximum. Statement 1005 Figure 10 shows the AC power supply for the Cisco ASR 1002-X Router.
  • Page 14 LED Label Color Description INPUT OK Power supply activity Green The AC input voltage is greater than 85V. None If the LED is not illuminated, then either the input voltage is less than 70V, or the power supply is turned off.
  • Page 15 12. Make sure the power cord is hanging loosely so that it cannot be disconnected from the AC power inlet. Figure 12 Cisco ASR 1002-X Router AC Power Cord - Left and Right OU TP UT INP UT FAI L...
  • Page 16 Step 8 This completes the procedure for connecting an AC power supply in the Cisco ASR 1002-X Router. You have completed a live change-out procedure (that is, removing and replacing an AC power supply) for an AC power supply not operating properly in the Cisco ASR 1002-X Router within five minutes.
  • Page 17 –48V Dopier supply LEDs Positive ground lead 10 Earth ground lead Table 2 describes the –48V DC power supply LEDs on the Cisco ASR 1002-X Router. Table 2 Cisco ASR 1002-X Router –48V DC Power Supply LEDs LED Label Color...
  • Page 18 Figure 14 Cisco ASR 1002-X Router –48V DC Terminal Block - 4 8 V / - 6 0 V 1 6 A Negative lead Earth ground symbol Positive lead Warning Never install an AC power module and a DC power module in the same chassis. Statement 1050 Warning Installation of the equipment must comply with local and national electrical codes.
  • Page 19 Turn the branch circuit breaker on at your site and the turn the Standby switch to the On (I) position. Step 8 Check that the power supply LEDs light when power is supplied to the router. Step 9 You have completed the procedure for connecting a –48V DC power supply in the Cisco ASR 1002-X Router.
  • Page 20 Features are provide for strain relieving the input wires from the terminal block on the front panel. The recommended branch circuit breaker for the Cisco ASR 1002-X Router +24V DC power supply is a 40Amp UL listed circuit breaker.
  • Page 21 To connect +24V DC power supply in the Cisco ASR 1002-X Router, follow these steps: Step 1 At the rear of the router, check that the power Standby switch is in the Standby position. Ensure that the positive and negative leads are disconnected from the site power source and the source circuit breaker Step 2 is turned off.
  • Page 22 Do not install wire into the terminal block that has not had its insulation removed. Caution Figure 19 Cisco ASR 1002-X Router +24V DC Power Supply Lead Wire Inserted into Terminal Block O U T P U T IN P U...
  • Page 23 Figure 21 Removing the Screwdriver from the Cisco ASR 1002-X Router +24V DC Power Supply O U T P U T IN P U...
  • Page 24 Figure 22 Cisco ASR 1002-X Router +24V DC Power Supply Lead Wires Installed O U T P U T IN P U F A N F A IL T h is u n it m ig h t h a ve m...

  • Page 25: Verifying Power Supply Operation

    OUTPUT FAILED is not illuminated – Step 2 To ensure that the power supply state is OK, type the show platform command. This output sample is from a Cisco ASR1002-X router. The other Cisco ASR1000 routers display similar type of output.
  • Page 26 Check the following conditions before you start the Cisco ASR 1002-X Router: • The Cisco ASR 1002-X Router has one slot for FP0 with three subslots for SPAs, subslots 1, 2, and 3. Make certain that each shared port adapter is firmly seated in its subslot and its captive screws are securely tightened.
  • Page 27 The system boots differently depending on the configuration that ships with your system. The display below is a snapshot of messages that are output on the console of the Cisco ASR 1002-X Router system after power-up and during IOS booting. This is only an example of what you might see from any Cisco ASR 1000 Series Router.
  • Page 28 Observe the initialization process. When the system boot is complete (a few seconds), the Cisco ASR 1002-X integrated Step 4 route processor begins to initialize. The console screen displays a script and system banner similar to the following when booting flash or harddisk: asr1002-16-rp0-rommon 2 >boot...
  • Page 29 "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com.

  • Page 30: Configuring The Router

    Aggregation Services Routers Software Configuration Guide. Configuring the Router Use this section for information on configuring the Cisco ASR 1002-X Router. • Using the Console to Access the CLI • Configure Global Parameters Using the Set-up Facility • Check the Running Configuration Settings •...

  • Page 31: Configure Global Parameters Using The Set-Up Facility

    Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 --- System Configuration Dialog ---...
  • Page 32 Enter host name [Router]: The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: test The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images.
  • Page 33 Proceed with reload? [confirm] *Jan 11 06:59:29.476: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command. System Bootstrap, Version 12.2(20071105:235056) [gschnorr-mcp_rommon_rel_1_25 101], DEVELOPMENT SOFTWARE Copyright (c) 1994-2007 by cisco Systems, Inc. Compiled Mon 05-Nov-07 16:50 by gschnorr-mcp_rommon_rel_1_25 Current image running: Boot ROM1...
  • Page 34 Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNA, RELEASE SOFTWARE Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 01-May-08 00:29 by mcpre...

  • Page 35: Check The Running Configuration Settings

    Basic management setup configures enough connectivity for managing the system; extended setup will ask you to Note configure each interface on the system. For detailed information about setting global parameters, refer to the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide.

  • Page 36: Configuring The Throughput Level

    Router#reload Perform Other Configuration Tasks To make advanced configuration changes after you establish the basic startup configuration for your router, refer to the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide and modular configuration and modular command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software release installed on your Cisco hardware.
  • Page 37 Powering Off the Cisco ASR 1002-X Router Safely This section explains how to shut down the Cisco ASR 1002-X Router. It is recommended that before turning off all power to the chassis, you issue the reload command. This insures that the operating system cleans up all the file systems. Once the reload operation is complete, then the Cisco ASR 1002-X Router can be powered off safely.

  • Page 38: Replace The Shared Port Adapters

    Slip on the ESD-preventive wrist strap that was included in the accessory kit. Loosen the captive screws on the Cisco Step 1 ESP5 or ESP10. Using the handles on both sides of the module, with two hands, gently slide the Cisco ESP5 or ESP10 out of the chassis Step 2 slot.
  • Page 39 Replace a Power Supply in the Cisco ASR 1002-X Router This section provides instructions for removing the AC power supply, the –48V DC and +24V DC power supply from a Cisco ASR 1002-X Router. This section contains the following topics: •...

  • Page 40: Removing An Ac Power Supply

    Removing an AC Power Supply To remove a Cisco ASR 1002-X Router AC power supply that is not operating normally (and then replace the AC power supply within five minutes), follow this procedure: Slip on the ESD-preventive wrist strap that was included in the accessory kit.
  • Page 41 You have removed an AC power supply from the Cisco ASR 1002-X Router and now must replace the AC power supply within five minutes. For replacing the AC power supply into the Cisco ASR 1002-X Router, see Connecting AC Power to the Cisco ASR 1002-X Router, page 15.
  • Page 42 Wire-stripping tool for stripping 8-gauge wire – Before you can remove a +24V DC power supply from the Cisco ASR 1002-X Router, you must remove input power going to the power supply. Make certain that the chassis ground lead wire is connected before you begin removing and installing the power Caution supply.
  • Page 43 Replace the +24V DC power supply within five minutes. You have completed the procedure for removing a +24V DC power supply from the Cisco ASR 1002-X Router. For replacing the +24V DC power supply into the Cisco ASR 1002-X Router, see...
  • Page 47 31 0 800 020 0791 Fax: 408 527-0883 Fax: 31 0 20 357 1100 Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices. © 2012 Cisco Systems, Inc. All rights reserved.

This manual is also suitable for:

Asr 1002-x

Table of Contents