Cisco ASR 1000 Series Hardware Installation And Configuration Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. ASR 1000 Series
  6. Hardware installation and configuration manual
Cisco ASR 1000 Series Hardware Installation And Configuration Manual

Cisco ASR 1000 Series Hardware Installation And Configuration Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Cisco ASR 1000 Series Routers Components
The Cisco ASR 1000 Series Routers contain the following components:
•
•
•
•
Throughout this document, the term slot refers to a Cisco ASR 1000 Series Router chassis slot. The
Note
Cisco ASR 1000 Series Route Processor 1, Cisco ASR 1000 Series Embedded Services Processor, and
Cisco ASR 1000 Series SPA Interface Processor, and power supplies plug into these slots. SPAs plug
into SIP bays.

Cisco ASR 1000 Series Route Processor 1

The Cisco ASR 1000 Series Route Processor 1 (RP1) is the central network clocking card and is
responsible for:
•
•
•
Specific system tasks performed by the Cisco ASR 1000 Series Route Processor 1including the
following:
•
•
•
•
OL-13208-01
Cisco ASR 1000 Series Route Processor 1, page 2-1
Cisco ASR 1000 Series Embedded Services Processor, page 2-8
Cisco ASR 1000 Series SPA Interface Processor, page 2-10
Cisco ASR 1000 Series Router Power Supplies, page 2-14
Cisco ASR 1000 Series Routers field-replaceable unit (FRU) online insertion and removal (OIR).
Selection of the active Cisco ASR 1000 Series Route Processor 1 and the Cisco ASR 1000 Series
Embedded Services Processor and notification of the Cisco ASR 1000 Series SPA Interface
Processor of these events.
All the control processors communicating and performing packet processing on packets punted to it
by the Cisco ASR 1000 Series Embedded Services Processor (ESP).
Runs the router control plane, including network control packets, and connection setup
User interfaces: 10/100/1000 Management Ethernet, CON/AUX, USB
Active and standby Cisco ASR 1000 Series Route Processor 1 and Cisco ASR 1000 Series
Embedded Services Processor master and standby synchronization (Tasks include switchover from
failing master to standby.)
Code storage, management, and upgrade
Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide
2
C H A P T E R
2-1

Advertisement

Table of Contents
loading

Related Manuals for Cisco ASR 1000 Series

Summary of Contents for Cisco ASR 1000 Series

  • Page 1: Cisco Asr 1000 Series Route Processor

    • Cisco ASR 1000 Series Router Power Supplies, page 2-14 Throughout this document, the term slot refers to a Cisco ASR 1000 Series Router chassis slot. The Note Cisco ASR 1000 Series Route Processor 1, Cisco ASR 1000 Series Embedded Services Processor, and Cisco ASR 1000 Series SPA Interface Processor, and power supplies plug into these slots.
  • Page 2 Cisco ASR 1000 Series Route Processor 1 Features The Cisco ASR 1000 Series Route Processor 1 (RP1) is the route processor that receives and transmits all network packets through the active embedded services processor. The Cisco ASR 1000 Series RP1: •...
  • Page 3 Cisco ASR 1000 Series Routers Components Cisco ASR 1000 Series Route Processor 1 Figure 2-1 shows the Cisco ASR 1000 Series RP1 faceplate for the Cisco ASR 1006 Router and ASR 1004 Router. Figure 2-1 Cisco ASR Series 1000 RP1 Faceplate LEDs and Connectors...
  • Page 4 Active indicator. bootflash LED No activity. CARRIER Out of service or not configured. Solid Green In frame and working properly. Amber Fault of loop condition exists. Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide OL-13208-01...
  • Page 5 Supports up to 4GB of ECC-protected memory with single-bit error correction and multi-bit error • detection Supports On-board Failure Logging (OBFL) with 2MB of memory • Supports the Cisco ASR 1000 Series Router system architecture, midplane, and the Cisco ASR 1006 • Router Enhanced Serdes Interconnect (ESI) at 11.5 G bps. •...
  • Page 6 Bulk storage is 40G hard disk drive (SSD optional) I/O support: 2 Mb upgradeable BootRom, 1GB Embedded USB memory (EUSB) • 512 MB embedded USB, 1GB on RP1 for Cisco ASR 1006 Router and ASR 1004 Router, and 8GB • on Cisco ASR 1002 Router •...
  • Page 7 The route processor has an ENET port with a RJ-45 copper Ethernet connector to attach a management device or network Management Ethernet for network management. Port Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide OL-13208-01...
  • Page 8 R0 slot Grounding stud The Cisco ASR 1000 Series Route Processor for the Cisco ASR 1002 Router deviates from the other route processor in the following ways: • No SATA hard drive supported. Bulk file storage is on a large fixed EUSB device (up to 8GB supported).
  • Page 9 – Cisco ASR 1004 Router physical slot 1 and is labeled F0. – Cisco ASR 1002 (which can use either the ESP10 or the ESP5; but Cisco ASR 1002 Router is – the only chassis that supports Cisco ASR1000-ESP5) Cisco ASR 1000 Series ESP5—Supports forwarding performance with up to 4 Mpps with baseline •...

  • Page 10: Cisco Asr 1000 Series Spa Interface Processor

    This section describes the SPA interface processor for the Cisco ASR 1006 Router, Cisco ASR 1004 Router and the Cisco ASR 1002 Router. The Cisco ASR 1000 Series SPA Interface Processor for the Cisco ASR 1006 and Cisco ASR 1004 routers: Is a carrier card that inserts into a router slot like a line card.
  • Page 11 Supports online insertion and removal (OIR) with SPAs inserted in the subslots. SPAs also support • OIR and can be inserted or removed independently from the SIP. This section describes the Cisco ASR 1000 Series SPA Interface (SIP) components and subslot identification. Figure 2-5 shows the Cisco ASR 1000 Series SPA Interface (SIP) module.

  • Page 12: Shared Port Adapters

    SPA). The Cisco embedded ASR1000-SIP10 on the Cisco ASR 1002 Router also functions as the base board for the Cisco embedded ASR1000-RP1. The Cisco 1002 Router has one slot for FP0 with three subslots for SPAs, subslots 1 - 3.
  • Page 13 Two full height (¼ rate or full rate or combination) SPAs with up to 32 ports per SPA • The slot numbering for the SPAs in the Cisco ASR 1004 Router is the same as in the Cisco ASR 1006 Router.

  • Page 14: Cisco Asr 1000 Series Router Power Supplies

    You are required to always have two power supplies installed in the chassis to insure sufficient cooling for the box. The system fans are inside the power supply unit and must spin for cooling. No Cisco ASR 1000 Series Router will operate for more than two to three minutes without two power supplies installed.
  • Page 15 Cisco ASR 1002 For example, the Cisco ASR 1002 Router DC power supply, with 16 Amp input rating must use an AWG #12 gauge wire for a 20Amp circuit breaker and an AWG #10 gauge wire for a 30Amp circuit breaker.

  • Page 16: Power Supplies For Cisco Asr 1006 Router

    Power Supplies for Cisco ASR 1006 Router The Cisco ASR 1006 Router can support up to 1200W output (AC and DC input). The 1200W power supply module consists of either an AC or DC input and 1200 watt output closed frame power supply with two DC voltage outputs: 12V and 3.3V.
  • Page 17 Cisco ASR 1000 Series Router Power Supplies Figure 2-9 shows the AC power supplies at the rear of the Cisco ASR 1006 Router.The Cisco ASR 1006 Router supports up to two power supplies. The power supply LEDs and connectors on the rear of the...
  • Page 18 70V or the power supply is turned off. For an AC input voltage between 70V and 85V, the INPUT OK LED can be either on, off, or flashing Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide 2-18 OL-13208-01...
  • Page 19 See Figure 5-18. The studs on the terminal block are similar to the safety ground device on the side of the Cisco ASR 1006 Note Router. For information on the safety ground lug on the side of the chassis.
  • Page 20 Output Fail alarm. When you turn the power supply on, the red LED illuminates for two to three seconds to test LED operation before going off. Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide 2-20 OL-13208-01...

  • Page 21: Power Supplies For Cisco Asr 1004 Router

    Power Supplies for Cisco ASR 1004 Router The Cisco ASR 1004 Router can support up to 735 W output (AC and DC input). The 735W power supply module consists of either an AC or DC input with two DC voltage outputs: 12V and 3.3V.
  • Page 22 Cisco ASR 1004 AC Power Supply LEDs and Connector Figure 2-12 shows the AC power supplies at the rear of the Cisco ASR 1004 Router.The Cisco ASR 1004 Router supports up to two power supplies. The power supply LEDs and connectors on the rear of the...
  • Page 23 70V or the power supply is turned off. For an AC input voltage between 70V and 85V, the INPUT OK LED can be either on, off, or flashing Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide 2-23 OL-13208-01...
  • Page 24 Cisco ASR Router 1004 DC Power Supply This section provides information about the DC power supplies on the rear of the Cisco ASR 1004 Router. For the maximum branch circuit for the DC power supply module, see Table 2-7.
  • Page 25 The LED remains amber and is active to around 20V +/-5V. The LED is not illuminated if the input is below –15V. Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide 2-25 OL-13208-01...

  • Page 26: Power Supplies For Cisco Asr 1002 Router

    AC input side contains a front panel with provisions for mounting screw, two built-in handles to extract the power supply, three status LEDs, and fans for power supply and system cooling. Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide 2-26...
  • Page 27 This section provides information about the AC power supplies on the rear of the Cisco ASR 1002 Router. The Cisco ASR 1002 Router system level cooling is provided by two 12 VDC type fans in each of the two power supply modules. The fans in each module are intended to provide system cooling back-up in the event of a single fan failure.
  • Page 28 Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide 2-28 OL-13208-01...
  • Page 29 DC power supply module must not exceed 30Amp. The Cisco ASR 1002 Router has two of the same type power supplies in power supply slot 0 and power supply slot 1. The power supply slot numbers are on the left side of the chassis and the power supplies are located on the floor of the chassis.
  • Page 30 Output Fail alarm. When you turn the power supply on, the red LED illuminates for two to three seconds to test LED operation before going off. Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide 2-30 OL-13208-01...
  • Page 31 –11.80 VDC –3.20 VDC Nominal –12.00 VDC –3.30 VDC Maximum –12.20 VDC –3.40 VDC Output Current Minimum –2.0 A –0.10 A Maximum –39 A –3.125 A Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide 2-31 OL-13208-01...
  • Page 32 Chapter 2 Cisco ASR 1000 Series Routers Components Cisco ASR 1000 Series Router Power Supplies Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide 2-32 OL-13208-01...

Table of Contents