Configuration Examples - Cisco ASR 1000 Series Software Configuration Manual

Configuring the 2-Port and 4-Port Channelized T3 SPAs
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
DSU mode 0, bandwidth 44210 Kbit, scramble 1, VC 0
The following example provides sample output for the serial interface on a channelized T3:
Router# show interfaces serial2/0/1/1:0
serial2/0/1/1:0 is down, line protocol is down
Hardware is SPA-2XCT3/DS0
MTU 1500 bytes, BW 832 Kbit, DLY 20000 usec,
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
VC 1: timeslot(s): 2-14, Transmitter delay 0, non-inverted data
To find detailed status and statistical information on a per-port basis for the 2-Port and 4-Port Channelized
T3 SPA, use the show controllers serial command:
Router# show controllers serial 0/2/0
Serial0/2/0 - (SPA-4XT3/E3) is up
Current mode is T3
Framing is c-bit, Clock Source is Line
Bandwidth limit is 44210, DSU mode 0, Cable length is 10 feet
rx FEBE since last clear counter 0, since reset 0
Data in current interval (30 seconds elapsed):
No alarms detected.
No FEAC code is being received
MDL transmission is disabled

Configuration Examples

This section includes the following configuration examples:
OL-14127-17
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicast)
0 runts, 0 giants, 0 throttles 0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 applique, 4 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions alarm present
reliability 255/255, txload 1/255, rxload 1/255
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions alarm present
1 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation
0 P-bit Err Secs, 0 P-bit Sev Err Secs
0 Sev Err Framing Secs, 1 Unavailable Secs
1 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs
0 Severely Errored Line Secs
0 Far-End Errored Secs, 0 Far-End Severely Errored Secs
10 CP-bit Far-end Unavailable Secs
0 Near-end path failures, 0 Far-end path failures
0 Far-end code violations, 10 FERF Defect Secs
0 AIS Defect Secs, 0 LOS Defect Secs
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS XE
Configuration Examples
Everest 16.5
251