Mitsubishi Electric QJ71GF11-T2 User Manual page 454

Error code
Parameter error (device range
D613
H
assignment error (RWr))
Parameter error (device range
D614
H
assignment error (RWr))
Parameter error (device range
D615
H
assignment error (RY))
Parameter error (device range
D616
H
assignment error (RY))
Parameter error (device range
D617
H
assignment error (RX))
Parameter error (device range
D618
H
assignment error (RX))
D619 to D61A
Parameter error
H H
Parameter error (device already in use
D61B
H
(RWw))
Parameter error (device already in use
D61C
H
(RWr))
Parameter error (device already in use
D61D
H
(RY))
Parameter error (device already in use
D61E
H
(RX))
D61F
CCPASET execution error
H
D620
Incorrect transient data
H
D621
Parameter error
H
Parameter error (total number of slave
D622
H
stations error)
D623
Parameter error (link scan mode error)
H
Parameter error (constant link scan
D624
H
time setting error)
Parameter error (block data assurance
D625
H
per station setting error)
452
Error
• Write the network parameters to the CPU module again.
• Correct the value in the size of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• Correct the value in the size of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• Correct the value in the size of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• Correct the value in the size of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• Correct the value in the size of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• Correct the value in the size of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• Correct the value in the offset or the size of the link device in the slave
station(s) (setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
Delete the network parameter settings in the programming tool, execute
"Write to PLC", and execute the CCPASET instruction again.
• Check the transient data at the request source, and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• Correct the total number of slave stations, and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• Correct the link scan mode, and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• Correct the value in the total number of slave stations (setting data), and
retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
• Write the network parameters to the CPU module again.
• Correct the value in the total number of slave stations (setting data), and
retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
Action