Mitsubishi Q00JCPU User Manual page 95

2
PERFORMANCE SPECIFICATION
Item
Program memory
Memory card (RAM)
Max. number
Memory Flash card
of files stored
card (ROM)
ATA card
Standard RAM
Standard ROM
No. of times of writing data into the
program memory
No. of times of writing data into the
standard ROM
No. of I/O device points (No. of points
usable on program)
No. of I/O points (No. of points
accessible to the actual I/O module)
*7
Internal relay [M]
*7
Latch relay [L]
*7
Link relay [B]
*7
Timer [T]
*7
Retentive timer [ST]
*7
Counter [C]
*7
Data register [D]
Extended data register [D]
*7
Link register [W]
Extended link register [W]
*7
Annunciator [F]
*7
Edge relay [V]
*7
Link special relay [SB]
*7
Link special register [SW]
*4 : The CPU module can execute up to 124 programs. The CPU module cannot execute 125 or more programs.
*5 : The one write operation may not be counted as one writing to a program memory.
The number of writing to the program memory can be checked by the special register (SD682 and SD683).
*6 : The one write operation may not be counted as one writing to the standard ROM.
The number of writing to the standard ROM can be checked by the special register (SD687 and SD688).
*7 : The number of points can be changed within the setting range. (
Table2.5 Performance Specifications
Q03UDCPU Q04UDHCPU
Q02UCPU
Q03UDECPU Q04UDEHCPU Q06UDEHCPU Q13UDEHCPU Q26UDHECPU
64
319 (When the Q3MEM-8MBS is used)
( One file register, one local device and sampling trace file only)
3 (One file for each file register, local device, and sampling trace)
128
2048 points
(X/Y0 to
7FF)
8192 points by default (M0-8191) (changeable)
8192 points by default (L0-8191) (changeable)
8192 points by default (B0 to 1FFF) (changeable)
2048 points by default (T0 to 2047) (changeable)
(Sharing of low- and high-speed timers)
The low- and high-speed timers are specified by the instructions.
The measurement unit of the low- and high-speed timers is set up by parameters.
(Low-speed timer: 1 to 1000ms, 1ms unit, 100ms by default)
(High-speed timer: 0.1 to 100ms, 0.1ms unit, 10ms by default)
0 point by default (sharing of the low- and high-speed retentive timers) (changeable)
The low- and high-speed retentive timers are specified by the instructions.
The measurement unit of the low- and high-speed retentive timers is set up by parameters.
(Low-speed retentive timer: 1 to 1000ms, 1ms unit, 100ms by default)
(High-speed retentive timer: 0.1 to 100ms, 0.1ms unit, 10ms by default)
• Normal counter, 1024 points by default (C0 to 1023) (changeable)
12288 points by default (D0 to 12287) (changeable)
8192 points by default (W0 to 1FFF) (changeable)
2048 points by default (F0 to 2047) (changeable)
2048 points by default (V0 to 2047) (changeable)
2048 points by default (SB0 to 7FF) (changeable)
2048 points by default (SW0 to 7FF) (changeable)
Universal model QCPU
Q06UDHCPU
124
288
511
256
*5
Max. 100000 times
*6
Max. 100000 times
8192 points (X/Y0 to 1FFF)
4096 points (X/Y0 to FFF)
0 points by default (changeable)
0 points by default (changeable)
Section 10.2)
2.5 Universal model QCPU
Q13UDHCPU Q26UDHCPU
*4
252
2
- 17
1
2
3
4
5
6
7
8