Table of Contents
Advertisement
(Key On / Engine Running or Not / Header Disengaged).
(Press PROGRAM and SELECT on CDM to enter programming mode).
NOTE: ENGINE MUST BE RUNNING TO CALIBRATE SENSORS (Page 44).
||
L1
D 1 3 0
T R A C T O R
||
L2
C 1 4 0
D 1 3 0 || S E T
L1
C 1 4 0 ||
L2
D 1 3 0 || K N I F E
L1
C 1 4 0 ||
L2
or
D 1 3 0 || D I S K
L1
C 1 4 0 ||
L2
D 1 3 0 || O V E R L O A D
L1
C 1 4 0 ||
L2
D 1 3 0 || H E A D E R
L1
C 1 4 0 ||
L2
C 1 4 0 ||
L2
D 1 3 0 || R E T U R N
L1
C 1 4 0 ||
L2
C 1 4 0 ||
L2
D 1 3 0 || D W A
L1
C 1 4 0 ||
L2
L1
L2
D 1 3 0 || H E A D E R
L1
C 1 4 0 ||
L2
D 1 3 0 || H A Y
L1
C 1 4 0 ||
L2
D 1 3 0 || A U G E R
L1
C 1 4 0 ||
L2
C 1 4 0 ||
L2
D 1 3 0 || S E T
L1
C 1 4 0 ||
L2
C 1 4 0 ||
L2
C 1 4 0 ||
L2
C 1 4 0 ||
L2
D 1 3 0 || S E T
L1
C 1 4 0 ||
L2
L1
L2
L1
L2
L1
L2
L1
L2
L1
L2
Form # 169017
OPERATOR'S STATION
DETAILED PROGRAMMING INSTRUCTIONS
Programming Menu Flow Chart
S E T U P ?
N O / Y E S
K N I F E
S P E E D ?
1 2 0 0
S P M
O V E R L O A D
1 0 0 0
S P M
O V E R L O A D
2 0 0 0
R P M
P R E S S U R E ?
4 0 0 0
P S I
I N D E X
R E E L
&
C O N V E Y O R
R E E L
O N L Y
T O
C U T
H E I G H T
&
H E I G H T
O N L Y
I N S T A L L E D ?
N O / Y E S
D 1 3 0 || S W A P
D W A
C 1 4 0 ||
C U T
W I D T H ?
2 0 . 5
F E E T
C O N D I T I O N E R ?
N O / Y E S
H D R
R E E L
R P M / M P H
R P M / K P H
T I R E
S I Z E ?
1 8 . 4 X 2 6
T U R F
1 8 . 4 X 2 6
B A R
2 3 . 1 X 2 6
T U R F
6 0 0 - 6 5
R 2 8
E N G I N E
I S C
N O / Y E S
D 1 3 0 || P R E S S
C 1 4 0 || I S C
R P M
D 1 3 0 || P R E S S
C 1 4 0 || I S C
R P M
D 1 3 0 || P R E S S
C 1 4 0 || I S C
R P M
D 1 3 0 || P R E S S
C 1 4 0 || I S C
R P M
D 1 3 0 || E X I T
E N G I N E
C 1 4 0 ||
If "NO" then jump to:
C A B
D I S P L A Y
Press to Advance to Next Item On Upper Line.
When the programming mode is entered the
header ID will be displayed on the top line of the
S P D ?
CDM using the last 4 display positions.
S P D ?
Pressing "SELECT" will go to the next line 1
(L1) menu selection. The turn signal "arrow"
keys are used to change the values. Pressing
M O D E ?
"PROGRAM" at any time will cancel the
programming mode / menus and return back to
Press to Change Values on Lower Line
M O D E ?
T I L T
H E A D E R
C O N T R O L S ?
N O / Y E S
Use the "arrow" keys to set the header cut
width. The header ID appears at the RHS.
DRAPER HEADER ONLY. Default will be
flashing. Use "arrow" keys to select.
S P D
Pressing "SELECT" will go to the next line 1
(L1) menu selection. The turn signal "arrow"
keys are used to change the values.
R P M ?
S E T
4 - W A Y S
T O
S E T
O F F
4 - W A Y S
T O
S E T
2 0 0 0
4 - W A Y S
T O
S E T
1 9 0 0
4 - W A Y S
T O
S E T
1 8 0 0
I S C ?
N O / Y E S
42
S E T U P ?
SELECT SWITCH
TURN SIGNAL SWITCHES
the main operating displays.
If "NO" then jump to:
C U T
W I D T H ?
Swaps the GSL reel fore / aft with the DWA console
controls. If NO jump to DWA AUTO UP & DOWN?
AUGER HEADER ONLY
For IMPERIAL display.
For METRIC display.
If "NO" then jump to:
C O N T R O L
L O C K S ?
This is used to set the Intermediate Speed
Control function for the engine. The default or
last selected rpm will be displayed first and will
be flashing.
The "arrow" keys are used to cycle between the
selections. When "SELECT" is pressed the
program goes to the EXIT ENGINE ISC? menu
selection.
If "NO" then jump to:
P R E S S
4 - W A Y S
(continued next page)
Issue – June 2008
T O
S E T
Advertisement
Table of Contents
