MacDon M155 Manual

ONGOING MAINTENANCE INTERVALS
TIME SERVICE
1. Check Tire Inflation.
2. Check Engine Oil Level.
3. Check Engine Coolant Level At Reserve Tank.
4. Clean Radiator, Hydraulic Oil Cooler, Charge Air Cooler,
10 Hours
and A/C Condenser.
or Daily
5. Check Hydraulic Oil Level.
6. Drain Fuel Filter Water Trap.
7. Fill Fuel Tank.
8. Check Hydraulic Hoses and Lines For Leaks.
1. Grease Caster Pivots.
2. Grease Walking Beam Center and Top Lift Link Pivots.
3. Grease Forked Caster Spindle Bearings.
50 Hours
4. Clean Cab Fresh Air Intake Filter.
5. Check Gear Box Oil Level.
100 Hours
1. Clean Cab Air Return Filter.
or
Annually
NOTE: Refer to M155 Operator's Manual for
250, 500, 1000, 1500, 2000, 5000 Hour and Annual Maintenance.
BREAK-IN INSPECTIONS
HRS ITEM CHECK
Every
0.25
Torque: 170 ft·lbf (230 N·m) dry.
Drive Wheel Nuts
Road
Refer to M155 Operator's Manual
or 1
Field
A/C Belt Tension
Caster Wheel Nuts Torque: 120 ft·lbf (163 N·m)
Caster Wheel Anti- Torque Inboard Bolt: 100 ft·lbf (135 N·m)
5
Shimmy Dampener Bolts Outboard Bolt: 85 ft·lbf (115 N·m)
Walking Beam Width
Torque: 330 ft·lbf (448 N·m)
Adjustment Bolts
Walking Beam Width
Torque: 330 ft·lbf (448 N·m)
Adjustment Bolts
10
Neutral Adjusted by Dealer
Hose Clamps: Air Intake,
Radiator, Heater and Hand-tighten unless otherwise noted
Hydraulic
Walking Beam Bolts Torque: 330 ft-lbf (448 N·m)
Caster Wheel Anti- Torque Inboard: 100 ft-lbf (135 N·m)
Shimmy Dampener Bolts Torque Outboard: 85 ft-lbf (115 N·m)
50
Main Gearbox Oil
Drive Wheel Oil Lubricant
Charge System & Hydrau- Change
lic Oil Filters (except lift)
Manifold Oil Filter
FLUIDS AND LUBRICANTS
DESCRIPTION /
FLUID VOL SPEC
INFORMATION
Sulphur (by weight)
ASTM
97 US 0.5% max.
Fuel: D-975
Gallons Water and Sediment
Diesel No.2
(367 L) (by vol) 0.05% max.
Grade S15
Lubricity 520 microns
Sulphur (by weight)
Fuel:
97 US 0.5% pref. 1% max.
Diesel No.1
Gallons n/a Water and Sediment
and No. 2
(367 L) (by weight) 0.1% max.
Mix
Lubricity 460 microns
Engine ASTM
6.6 US
Coolant D-6120 and Refer to M155
Gallons
(Anti Fleetguard ES Operator's Manual
(25 L)
Freeze) Compleat
1.5 US SAE 75W-90 Fully synthetic gear
Drive Wheel
Quarts API service lubricant (SAE J2360
Lubricant
(1.4 L) Class GL-5 preferred)
High Temperature
Extreme Pressure
EP2. Maximum 1%
SAE Multi-
Grease N/A molybdenum disul-
Purpose
phide, Lithium base.
Use as required unless
otherwise noted
11.6 US SAE 15W-40
Engine Oil Quarts for API Class Engine Oil Pan
(11 L) SJ and CH-4
SAE 15W-40
17.2 US for API Class
Hydraulic Windrower Drive and
Gallons CJ-4. Refer to
Oil Header Drive
(65 L) Operator's
Manual
SAE 75W-90
2.2 US API service Fully synthetic gear
Gear Box
Quarts Class GL-5 lubricant for
Lube
(2.1 L) (SAE J2360 Engine Gearbox
preferred)
A/C 5 lb.
R134A Cab A/C System
Refrigerant (2.27 kg)
A/C
8.1 fl. oz SP-15 Cab A/C Compressor
Compressor
(240 cc) PAG Lubricant
Oil
TIRE PRESSURES
18 - 26 BAR 600 - 65 R28 BAR
580 / 70 R26
32 psi (221 kPa) 26 psi (179 kPa)
TURF
Drive
Tires 24 psi
18.4 - 26 TURF 23.1 - 26 TURF
(165 kPa)
35 psi (241 kPa) 20 psi (138 kPa)
Rear
All Rear Tire Pressures are 10 psi (69 kPa)
Tires
FLOAT PRESETS
A-Series, R-Series, or D-Series -
Without Hydraulic Deck Shift
FLOAT PRE-SET / DECK SHIFT switch allows for
auto-memory of three different trim cylinder
positions. For example:
#1 - Border Width LH 5.0, RH 6.5
#2 - Normal Width LH 5.0, RH 5.0
#3 - Rocky Width LH 6.5, RH 6.5
D-Series with Hydraulic Deck Shift
DECK SHIFT switch activates hydraulic deck shifting
when the header is engaged, and allows for auto-
memory of trim cylinder adjustments in each delivery
opening position.
Allows for compensation of weight shifts to the float
springs.
NORMAL START - Engine Temp above 60°F (16°C)
1. Main battery disconnect switch - POWER ON.
2. GSL in N-DETENT. HEADER DRIVE switch OFF.
3. Seat Belt ON. Set throttle to START position - "fully back".
4. Sound horn three times.
5. Turn ignition key to RUN position. Single loud tone sounds.
Engine warning lights flash in self-test mode, and CDM displays
"HEADER DISENGAGED" and "IN PARK".
6. Turn ignition key to START position until engine starts.
Release key. Allow engine to run at IDLE until temperature
° °
reaches 100 F (40 C).
7. CDM displays programmed header data for 5 seconds,
and then returns to previous display.