Edit Program - Korg KRONOS SGX-2 Parameter Manual

Combination mode
IFX-All: The settings of all insert effect settings (the
contents of the Insert FX page and the IFX1–12 effect
parameters) of the copy-source program will be copied.
IFX-All used: Only the insert effects used by the copy-
source program will be copied. The copied settings will
be packed into vacant slots (i.e., slots with 000: No
Effect, unless such slots are located inside the chain).
Note: Copy-source insert effects set to 000: No Effect
will not be copied. However, if 000: No Effect is located
inside the chain, it will be copied.
MFXs: All master effect settings of the copy-source
program will be copied.
TFXs: All total effect settings of the copy-source
program will be copied.
About the Bus Select (8–1b, 8–2a, 8–5a) setting
• Regardless of the IFX-All, IFX-All used, MFXs, and
TFXs settings, will be set to DKit if the copy-source
program's "Use DKit Setting" is checked. In conjunction
with this, the "Drum Kit IFX Patch" setting will be reset
to the default setting.
• If IFX-All is checked, the Bus Select setting of the copy-
source program will be copied. If the copy-destination
timbre Bus Select was set to IFX1–IFX12, it will
automatically be set to L/R. If you check IFX-All used,
the routing will be automatically set to match the copy-
source program.
• If IFX-All and IFX-All used is unchecked, then the
copy-source Bus Select setting will be ignored. or if the
Bus Select of the copy-source program and copy-
destination timbre is set to IFX1–IFX12, it will
automatically be set to L/R.
4. If you check "with KARMA," the Program's
KARMA settings will also be copied.
If this is On (checked), the KARMA Module settings of
the copy-source program will be copied to the KARMA
Module you specify in step 6. The Pads settings will be
also be copied.
In Combination mode, the KARMA Module's "Input
Channel" will be set to Gch, its "Output Channel" will be
set to the MIDI channel of the timbre you specify in step
5, and "Track Thru" will be turned On (checked).
5. Use the "To" field to specify the copy-destination
timbre.
The parameters for each timbre will be initialized. The
copy-source program will be assigned to "Program" ("0–
1b: Timbre Program Select" on page 428).
• The MIDI Channel (2–1a) setting will not change if
"with KARMA" is checked. If "with KARMA" is
unchecked, MIDI Channel will be automatically set to
G ch.
• The Status (2–1a) setting will automatically be set to
INT.
• The P1–Set Up Controller settings of the copy-source
program will be copied.
6. Use the "Module" field to select the copy-destination
KARMA Module; either A, B, C, or D.
7. Press the OK button to execute the copy. If you decide
not to execute, press the Cancel button.
516

Edit Program

This command, available on the P0–1: Program
Select/Mixer page in Combi mode and the P0–1: MIDI Prog
Select/Mixer page in Sequencer mode, allows you to edit a
Program from within a Combination or Song, while still
hearing all of the other Timbres or Tracks.
To do so:
1. Go to the P0–1: Program Select/Mixer page in Combi
mode, or the P0–1: MIDI Prog Select/Mixer page in
Sequencer mode.
To edit a Program in context, either:
2. Select any parameter in the column of the Timbre or
Track which contains the Program you'd like to edit,
and then select the Edit Program command from the
menu.
You can select any parameter in the Timbre/Track's column,
including Volume, Pan, Status (Combinations only), and
Program Bank/Number.
Note: this is different from selecting a Timbre or Track via
the Control Surface.
or:
2a.Hold the ENTER button, and then touch the
Program's name in the Timbre or Track.
The system will then display the P0 page for the selected
Program. The front-panel PROGRAM button's LED will
blink, and the COMBI or SEQ LED will remain solidly on,
to show that you are editing the Program in context.
3. Edit as desired.
Eventually, if you want to keep your changes, you'll need to
Write the Program. However, while you're working, you can
go back and forth between the edited Program and the
Combination or Song.
You'll notice that some Program pages and tabs will be
grayed out; for more information, see "Parameters
unavailable while editing in context," below.
To return to the Combination or Song:
4. Press the front-panel COMBI or SEQ buttons.
or:
4a.Press the EXIT button until the Program P0 page
appears, and then press EXIT once again.
To go back to editing the Program, just repeat steps 2 or 2a,
above.
The normal rules of editing apply: if you select another
Program, all edits to the previous Program will be lost. So,
make sure to save your work:
5. While on the Program edit pages, use the Write menu
command to save your edits.
Note that you must be on the Program edit pages in order to
Write the Program edits. Writing the Combination or Song
will not affect the Program.
If you Write the Program to different bank/number, the
Combination Timbre or Song Track selected in step 2 or 2a,
above, will be updated to reference the new location. In this
case, if other Timbres or Tracks use the Program, they will
not be updated automatically (since you may want them to
continue to play the original Program); you can change them
manually if desired.