083: Stereo Dynamic Delay - Korg KRONOS SGX-2 Parameter Manual

MIDI/Tempo Sync
BPM
Base Note
Times
When MIDI/Tempo Sync is on, the LFO speed is set by
BPM, Base Note, and Times, instead of Frequency. For
more information, see "MIDI/Tempo Sync" on page 921.
Type [Individual, Common1, Common2]
This controls whether the effect uses its individual LFO, or
one of the Common FX LFOs. For more information, see
"LFO Type" on page 921.
Common LFO Phase Offset [degrees]
When Type is set to Common FX LFO 1 or 2, this lets you
offset the phase from the master LFO.
MOD DELAY
L Delay Time [msec]
Sets the delay time for the left channel.

083: Stereo Dynamic Delay

This stereo delay uses the input signal level to control either
the wet/dry mix or the feedback level. You can use this to
create:
• Ducked delays, in which the delays get softer when the
input is loud (the delays "duck" to get out of the way).
• Gated delays, in which the delays are louder when the
input is loud. For instance, you can create a thick,
layered lead sound using delays, and then make the level
or feedback of the delays reduce automatically when you
stop playing.
Stereo In - Stereo Out
Left
High Damp Low Damp
Delay
Feedback
High Damp Low Damp
Delay
Right
FB
+
Attack, Release
Envelope
Threshold
CONTROL
Target [None, Output Level, Feedback]
This selects the modulation target for the input signal.
Output Level modulates the Wet/Dry mix.
Feedback modulates the Feedback amount.
Polarity
+ (positive): The modulation applies only when the input
signal is below the Threshold. Use this to lower the effect
level when the input signal is quiet.
– (negative): The modulation applies only when the input
signal is above the Threshold. Use this to lower the effect
level when the input signal is loud (for "ducking").
[Check-box]
[MIDI, 40.00...300.00]
[r ... w ]
[x1...x32]
[+/–180]
[0.0...1000.0]
Wet / Dry
Spread
Wet / Dry
Out
Control Target
[+, –]
Delay 083: Stereo Dynamic Delay
R Delay Time [msec]
Sets the delay time for the right channel.
L Depth
Sets the amount of pitch modulation for the left channel.
0...100 produce chorus-like effects; over 100 produces more
obvious pitch-shifting.
R Depth
Sets the amount of pitch modulation for the right channel.
L Feedback
Sets the amount of feedback for the left delay. Negative
values invert the phase.
R Feedback
Sets the amount of feedback for the right delay.
OUTPUT
This is the standard effects output section, with modulatable
control over wet/dry balance. For more information, see
"OUTPUT" on page 904.
Offset
This controls the amount of modulation for the Target
parameter (either Output Level or Feedback), as a
percentage of the parameter's value.
Threshold
This sets the input signal level at which the ducking or
gating occurs, according to the Polarity setting.
Attack
This controls how fast the gating or ducking starts after the
Threshold is crossed.
Release
This controls how fast the gating or ducking stops, after the
Threshold is crossed in the opposite direction.
Level
Dry
Threshold
Envelope
Attack
Wet (Ducking Delay)
Target=Output Level
Polarity= (–)
Delay Time
Wet
Target=Output Level
Polarity= (+)
[0.0...1000.0]
[0...200]
[0...200]
[+/–100]
[+/–100]
[0...100]
[0...100]
[1...100]
[1...100]
Dynamic Delay
Release
Time
979