Korg KRONOS SGX-2 Parameter Manual page 129

MIDI IN
KRONOS controllers
Ribbon (CC#16)
Specifies whether MIDI control change message #16
(internal ribbon controller, specified as the assignment of a
real-time control knob, or Vector CC Control) will be echoed
to the tone generator.
Other CC
Specifies whether MIDI control change messages other than
the above will be echoed to the tone generator.
Transmit MIDI Filter
Specifies whether filtering will be applied to the MIDI
control data produced by the GE selected for the KARMA
Module. (See the diagram on the preceding page, "KARMA
Receive/Transmit Filter.")
On (checked): The corresponding MIDI data will be
transmitted from the KARMA Module.
Off (unchecked): The corresponding MIDI data will not be
transmitted from the KARMA Module.
Note: The GE can also automatically produce pitch bend and
various types of control change messages in addition to note
data. Three envelope generators can also be used to apply
time-variant change to velocity, tempo, duration, and various
control changes such as pitch bend, JS +Y (CC#1) etc.
The data that is output will depend on the settings of the
parameters for the selected GE. For example,
transmitting/filtering pitch bend will produce no result if the
GE has not been designed to produce pitch bend data. For
more information, please see the separate Voice Name List
(VNL).
Pitch Bend
Specifies whether to transmit the MIDI pitch bend messages
generated by the GE selected for the KARMA Module.
Note: This setting also applies to the pitch bend messages
that may be produced by CC–A, CC–B, Envelope 1,
Envelope 2, and Envelope 3.
When KARMA is on and the KARMA Module is
producing pitch bend data, the pitch bend range of the
program will be controlled as follows.
The pitch bend range specified within KARMA GE will
automatically be transmitted from the KARMA Module,
and set within the program. This ensures that the pitch
bend data produced by the GE of the KARMA will
function correctly. At this time, the pitch bend data
produced when you operate the joystick will
Program P7: KARMA 7–2: MIDI Filter/CC Offset
KARMA function
KARMA Module
Receive MIDI
Transmit MIDI
GE
Dynamic MIDI
[Off, On]
automatically be optimized so that it will produce the
same bend effect as if the KARMA were off (in most
cases).
CC–A/CC–B
Specifies whether to transmit the various MIDI messages
[Off, On]
generated by CC–A/CC–B of the GE selected by the
KARMA Module.
However if CC–A/CC–B are producing pitch bend
messages, these settings will be ignored, and the "GE
Bend" setting will be used.
Envelope1/Envelope2/Envelope3
Specifies whether to transmit the various MIDI messages or
other functions generated by Envelope 1, Envelope 2, and
Envelope 3 of the GE selected by the KARMA Module.
If Envelope 1, Envelope 2, or Envelope 3 are producing
pitch bend messages, these settings will be ignored, and
the "GE Bend" setting will be used.
GE Notes
Specifies whether the MIDI note-on/note-off messages
generated by the KARMA Module will be transmitted.
Note: This setting lets you mute the note phrases generated
by the KARMA Module, and use only the control data
generated from the KARMA Module (e.g., pan, filter cutoff,
resonance) to apply modulation to phrases or chords you
yourself play on the keyboard.
WaveSeq
Specifies whether the wave sequence data (multisample
number) generated by the KARMA Module will be
[Off, On]
transmitted.
7–2c: CC Offset
When KARMA is turned on, MIDI control change
messages can be transmitted to the tone generator. Make
these settings when you wish to control the program sound
or effects etc. when KARMA is turned on.
You can assign up to four MIDI control changes for each
KARMA Module.
1, 2, 3, 4
CC Number
Selects the MIDI control change message that will be
transmitted.
Filter
Tone
Filter
generator
[Off, MIDI CC# 00...MIDI CC# 95]
[Off, On]
[Off, On]
[Off, On]
[Off, On]
115