Korg KRONOS SGX-2 Parameter Manual page 637

On (checked): The Bus Select, FX Control Bus, Send1,
and Send2 settings for each key of the selected drum kit will
be used. Check this setting if you want to apply an individual
insert effect to each drum instrument, or to send individual
drum instruments to AUDIO OUTPUT (INDIVIDUAL).
Tip: In most preloaded drumkits, the drum instruments have
the same Bus Select settings according to their type, as
follows.
Snares IFX1
Kicks IFX2
Toms IFX3
Cymbals IFX4
Percussion etc. IFX5
If you want to edit these routings, use the "Drum Kit IFX
Patch" page menu command. For details, see "Drum Kit IFX
Patch" on page 521.
Off (unchecked): The Bus Select, FX Control Bus, and
Send 1/2 settings will be used. All drum instruments will be
sent to the specified bus.
Bus Select (IFX/Indiv.Out Assign)
[L/R, IFX1...12, 1...4, 1/2...3/4, Off]
This specifies the output bus for the track's program
oscillator. This parameter can also be edited from the P8–
MIDI Routing 2 page.
L/R: Output to the L/R bus.
IFX1...12: Output to the IFX1–12 buses.
1...4: The track will be output in mono from the
corresponding AUDIO OUTPUT (INDIVIDUAL).
1/2...3/4: The track will be output in stereo according to its
pan setting from the corresponding AUDIO OUTPUT
(INDIVIDUAL) pairs.
Off: The track will not be output from the L/R bus, IFX1–12
buses, or Individual 1–4 buses. Choose the Off setting if you
want the program oscillator output of the track to be
connected in series to a master effect. Use Send1 (to MFX1)
and Send2 (to MFX2) to specify the send levels.
Tip: You can create a wide variety of routings by using each
track's Bus Select and the Chain to and Chain settings (8–
5a) that follow the insert effect.
Send1 (MFX1)
Send2 (MFX2)
For each track, these parameters set the send level to master
effects 1 and 2. These settings are valid when Bus Select is
set to L/R or Off. When IFX 1–12 are selected, the send
levels to master effects 1 and 2 are set by the Send1 and
Send2 parameters of the Insert FX page, after the sound has
passed through IFX1–12.
If Bus Select is set to 1...4 or 1/2...3/4, these settings are
ignored.
The Send 1 and 2 setting you specify here are used when
playing-back or recording from the beginning of the song. If
you modify these settings during recording, your changes
will be recorded as performance data; the send amounts will
change accordingly during playback. You can also modify
these settings during playback. However if Send 1 and 2 data
has been recorded, the settings will change according to the
recorded data.
Sequencer P8: Insert Effect 8–1: MIDI Routing1
Note: You can use the control surface to control Send1 and
Send2. These can also be controlled from the mixer section
of the front panel, or from the P0– Control Surface page of
the LCD screen. The procedure given below describes how
to make these settings from the front panel.
1. Press the CONTROL ASSIGN MIXER
TIMBRE/TRACK switch to select either tracks 1–8 or
9–16.
2. Press the MIXER KNOBS switch to select CHANNEL
STRIP.
3. Use the MIXER SELECT 1/9–8/16 switches to select
the track whose send levels you want to adjust.
4. Use MIX CHANNEL STRIP "FX SEND 1" (knob 7)
and "FX SEND 2" (knob 8) to control the send levels.
If Bus Select (IFX/Indiv. Out Assign) is set to L/R or
Off, this will control "Send1 (MFX1)"–"Send2 (MFX2)."
If Bus Select (IFX/Indiv. Out Assign) is set to IFX1–12,
this will control Send1 and Send2 (P8– Insert FX page).
If Status (2–1a) is either INT or BTH, CC#93 and #91
can be received to control send 1 and 2 respectively and
change their settings. When you switch songs or return to
the beginning of a song, tracks whose Status is EXT,
EX2 or BTH will transmit these settings via MIDI. This
data will be transmitted on the MIDI channel of each
track as set by MIDI Channel (2–1a). The actual send
level is determined by multiplying the value of these
parameters with the send level settings of the oscillator(s)
of the program used by the track (Send1 and "Send2,"
Program 8–1d).
Track 02...16 (Track Number)
These settings specify the program oscillator output bus and
master effect send levels for MIDI tracks 2 through 16. They
are the same as for track 1. See "Track 01":.
v 8–1: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see "ENTER + 0-9: shortcuts for menu
commands" on page 153.
• 0: Memory Status. For more information, see "Memory
Status" on page 637.
[000...127]
• 1: Exclusive Solo. For more information, see "Exclusive
Solo" on page 153.
[000...127]
• 2: Copy Insert Effect. For more information, see "Copy
Insert Effect" on page 166.
• 3: Swap Insert Effect. For more information, see "Swap
Insert Effect" on page 166.
• 4: Drum Kit IFX Patch. For more information, see
"Drum Kit IFX Patch" on page 521.
• 5: Put Effect Setting To Track. For more information,
see "Put Effect Setting to Track" on page 670.
• 6: FF/REW Speed. For more information, see "FF/REW
Speed" on page 638.
• 7: Set Location (for Locate Key.) For more information,
see "Set Location (for Locate Key)" on page 639.
623