Set Location (For Locate Key); Gm Initialize; Copy From Combi; Copy From Program - Korg KRONOS SGX-2 Parameter Manual

Set Location (for Locate Key)

This sets the Sequencer's locate point. When you press the
LOCATE switch, the Song will move to the measure, beat,
and tick specified here.
1. Select Set Location to open the dialog box.
2. Specify the location to which the Song will move when
you press the LOCATE switch.
From the left, the values are Measure (001–999), Beat
(01–16), and Tick (000–479).
If you set this to 001:01.000, pressing LOCATE brings
you back to the beginning of the song.
3. To execute the settings, press the OK button. To
cancel, press the Cancel button.
Note: When this dialog box is not open, you can hold down
the ENTER switch and press the LOCATE switch to set the
current location as the locate point.

GM Initialize

This command transmits a GM System On message to the
Sequencer mode, resetting all MIDI tracks to the GM
settings (See "GM Initialize menu command -
Automatically-set parameters and their values" on
page 640).
1. Select "GM Initialize" to open the dialog box.
2. To execute the settings, press the OK button. To
cancel, press the Cancel button.
In Sequencer mode, when a GM System On message is
received from an external device, or if a GM System On
message is recorded in the sequence data, the KRONOS
will be reset to settings appropriate for GM just as if you
had executed this command. However, in these cases, the
various P9: Master/Total Effect parameters will not be
reset.

Copy from Combi

This command copies the parameters of the specified
combination to the setting data of the currently selected
song.
Note: Only the timbres used by the combination will be
copied. Timbres in the combination whose Status is Off will
not be copied. If any timbres are set to Mute, the
corresponding tracks of the song will be set to a Status of
Off. However if none of the timbres used in the combination
have a MIDI channel setting of Gch, a MIDI track whose
MIDI channel is Gch will automatically be specified, and
Sequencer: Page Menu Commands Set Location (for Locate Key)
that track will be selected in Track Select. After the copy is
executed, you will immediately be able to play in the same
state as that combination.
1. Select "Copy from Combination" to open the dialog
box.
2. In "Combination," select the copy source destination.
3. Use the IFX-All, IFX-All used, MFXs and TFXs check
boxes to specify whether you want the effect settings
of the combination to be copied as well.
IFX-All: All insert effect settings of the copy-source
combination (the contents of the Insert FX page and the
IFX1–12 effect parameters) will be copied.
IFX-All used: Only the insert effects that are used by the
copy-source combination will be copied. When copied,
they will be packed into unused slots (000: No Effect,
unless within a chain).
Note: Copy-source insert effects that are set to 000: No
Effect will not be copied. However if 000: No Effect is
included within a chain, it will be copied.
If an entire chain in the copy-destination consists of 000:
No Effect, it will be used as a copy-destination.
MFXs: All master effect settings of the copy-source
combination will be copied.
TFXs: All total effect settings of the copy-source
combination will be copied.
4. Specify the desired Multi REC Standby setting.
On: The Status will automatically be set to REC for
MIDI tracks corresponding to valid timbres in the copy-
source combination. In addition, "Multi REC" (0–1a) will
automatically be turned on, and Recording Setup (0–5a)
will be set to Overwrite.
5. To execute the Copy operation, press the OK button.
To cancel, press the Cancel button.

Copy From Program

This command copies settings from the program you specify
to the currently selected song.
This is the same function as in Combination mode; for
details, see "Copy From Program" on page 515.
This command in Sequencer mode differs from its behavior
in Combination mode in that the channels assigned to the
tracks of the song will be preserved regardless of the "with
KARMA" setting of the copy-destination track's "MIDI
Channel." (See step 4.)
639