Table of Contents
Advertisement
Program mode: HD-1
In addition to the parameters initialized with the Off
(unchecked) setting, the following parameters will also be
initialized.
• 7-5: GE Real-Time Parameters/Scene page, Drum Track
Run setting.
• 7–6: Perf Real– Time Parameters page parameters.
• 7–7: Dynamic MIDI page parameters.
Copy Scene
Copy Scene is available on all of the KARMA pages, as
well as the KARMA GE tab of the Play page. It's also
available on the Control Surface page, when CONTROL
ASSIGN is set to Real-Time Knobs/KARMA.
This command copies settings for the KARMA Scenes. You
can use this command when you want to make settings for a
scene based on the other scene settings you edited, or vice
versa.
1. Choose "Copy Scene" to open the dialog box.
2. In "From:" select the scene that you wish copy.
3. In "To:" select the copy destination scene.
4. To execute the copy, press the OK button. To cancel
without executing, press the Cancel button.
Swap Scene
Swap Scene is available on all of the KARMA pages, as
well as the KARMA GE tab of the Play page. It's also
available on the Control Surface page, when CONTROL
ASSIGN is set to Real-Time Knobs/KARMA.
This command swaps (exchanges) the settings of two
KARMA Scenes.
1. Choose "Swap Scene" to open the dialog box.
2. In "Source1" and "Source2", select two KARMA
Scenes. that you wish to swap.
3. To execute the swap, press the OK button. To cancel
without executing, press the Cancel button.
Capture Random Seed
Capture Random Seed is available on all of the KARMA
pages, as well as the KARMA GE tab of the Play page.
The Start Seed is the source of the randomness of the phrase
generated by the KARMA Module. For more information,
see "Start Seed" on page 130.
When you are listening to the randomly changing phrases
generated each time a KARMA Module is triggered, and you
hear a phrase that you would like to reproduce consistently
each time you trigger that GE, you can execute this
command to capture the seed that resulted in that phrase.
For more information, see "Checking the Freeze Randomize
function, and performing "Capture Random Seed"" on
page 164.
164
1. Select "Capture Random Seed" to open the dialog
box.
2. If you are in a mode that can use more than one
KARMA Module (Combination or Sequencer modes),
use "To:" to select the module for which you want to
capture the seed value.
If you select A–D, the seed value will be captured for that
KARMA Module. If you select All, the seed values will
be captured for all four KARMA Modules.
In Program mode, this is fixed at A.
3. To execute the Capture Random Seed, press the OK
button. To cancel without executing, press the Cancel
button.
If the "Start Seed" parameter (see "Start Seed" on
page 134) of the KARMA Module for which you execute
Capture Random Seed is assigned as a Perf Real-Time
Parameter (see "7–6b: Perf Real-Time Parameters" on
page 127), the message "Could not execute Capture
Random Seed because the selected Start Seed is assigned
as an RTParm" will be displayed, and Capture Random
Seed will not be executed. (Press the OK button to close
the message.)
If you set the "To:" field of the dialog box to ALL
(Combination, Sequencer mode) to execute Capture
Random Seed for all KARMA Modules, Capture
Random Seed will be executed only for the KARMA
Modules whose "Start Seed" parameter is not assigned as
an Perf Real-Time Parameter. If the "Start Seed"
parameter of any KARMA Module is assigned as a Perf
Real-Time Parameter, Capture Random Seed will not be
executed for those KARMA Modules.
Checking the Freeze Randomize function, and
performing "Capture Random Seed"
By using the "Capture Random Seed," "Start Seed" (7–8b),
and "Freeze Loop Length" (7–8b) settings, you can loop a
randomly changing phrase as desired, or generate the same
phrase each time you trigger the GE.
Procedure
An example of the procedure in Program mode is shown
below.
1. In Program mode, select INT-D061: Widow Maker.
Advertisement
Table of Contents
