Korg KRONOS SGX-2 Parameter Manual page 574

Sequencer mode
Off: the Program's EQ settings won't be loaded. Use this if
you've set up the EQ in a specific way, and then want it to
stay unchanged while you try out different Programs.
Bypass
If this is On (checked), all of the EQ will be disabled,
including "Input Trim." Bypass can be convenient for
comparing the results of the EQ with the original signal.
Input Trim
This controls the volume level going into the EQ. Note that
this parameter uses a linear scale; 50 is equivalent to –6dB,
25 is the same as –12dB, and so on.
High settings of the Low, Mid, and High Gain controls can
cause substantial increases in the overall level. You can
compensate for this by turning down the input trim.
The meter to the left of the parameter shows the post-EQ
signal level in realtime.
High Gain
This controls the gain of the 10kHz High Shelf EQ, in
increments of 0.5dB.
Mid Frequency
This sets the center frequency for the Mid sweep EQ.
Mid Gain
This controls the gain of the Mid Sweep EQ, in increments
of 0.5dB.
Low Gain
This controls the gain of the 80Hz Low Shelf EQ, in
increments of 0.5dB.
MIDI Track EQ and the control surface
You can use the Control Surface to adjust almost all of the
Track EQ parameters (except for Bypass). To do so:
1. Press the CONTROL ASSIGN MIXER
TIMBRE/TRACK switch to select either Tracks 1–8
or 9–16.
2. Use the MIX SELECT 1/9–8/16 switches to select the
Track you want to control.
3. Press the MIXER KNOBS switch to select CHANNEL
STRIP.
4. Use the MIX CHANNEL STRIP knobs 2-6 to adjust
the EQ TRIM, LOW EQ gain, MID EQ frequency
and gain, and HIGH EQ gain, as desired.
Track 02...16 (Track Number)
These parameters adjust the three-band EQ (with sweepable
mid range) for MIDI tracks 2 through 16. They are the same
as for track 1. See "Track 01":.
v 1–1: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see "ENTER + 0-9: shortcuts for menu
commands" on page 153.
• 0: Memory Status. For more information, see "Memory
Status" on page 637.
• 1: Exclusive Solo. For more information, see "Exclusive
Solo" on page 153.
560
[Off, On]
[00...99]
[–18.0...+18.0dB]
[100Hz...10.00kHz]
[–18.0...+18.0dB]
[–18.0...+18.0dB]
• 2: Rename Song. For more information, see "Rename
Song" on page 637.
• 3: Initialize Song. For more information, see "Initialize
Song" on page 637.
• 4: Copy From Song. For more information, see "Copy
From Song" on page 637.
• 5: Load Template Song. For more information, see
"Load Template Song" on page 637.
• 6: Save Template Song. For more information, see
"Save Template Song" on page 638.
• 7: FF/REW Speed. For more information, see "FF/REW
Speed" on page 638
• 8: Set Location (for Locate Key.) For more information,
see "Set Location (for Locate Key)" on page 639.
• 9: GM Initialize. For more information, see "GM
Initialize" on page 639.
• 10: Copy From Combi. For more information, see
"Copy from Combi" on page 639.
• 11: Copy From Program. For more information, see
"Copy From Program" on page 639.
• 12: Show EQ Graphic. For more information, see
"Show EQ Graphic" on page 519.