Korg KRONOS SGX-2 Parameter Manual page 208

EXi: AL-1 Analog Synthesizer
Transpose
This adjusts the pitch in semitones, over a range of ±1
octave.
Tune
This adjusts the pitch in cents, over a range of ±1 octave. A
cent is 1/100 of a semitone.
Frequency Offset
This adjusts the pitch by increments of 0.1 Hz. Frequency
Offset is different from Tune in that, when used to detune
the two oscillators, it can create a constant beat frequency
across the range of the keyboard.
Randomizing frequency for an analog feel
You can use various methods to randomize the oscillator
frequency, in order to simulate the instability of analog
oscillators:
• Simulate analog drift by modulating pitch with one of
the Continuous Random LFO waveforms.
• Use Tune or Frequency Offset to detune the oscillators
a tiny bit.
• Set the Scale Random parameter (in the Common
section, Basic/Vector page, EXi Basic tab) to 1,2, or 3 to
create small amounts of random pitch variation at note-
on.
4–1b: Oscillator 2
Oscillator 2 is very similar to Oscillator 1, as described
above. The only differences are:
• Oscillator 2 does not include the Triangle or
Square/Triangle waveforms.
• Oscillator 2's pitch does not affect the Sub-Oscillator.
• When Sync is enabled, Oscillator 2's Initial Phase
setting affects only the very beginning of the sound,
before Oscillator 1 completes its first cycle. After that,
Oscillator 2's phase is controlled by Oscillator 1.
4–1c: FM/Sync
FM Amount
Oscillator 1 is the modulator, and Oscillator 2 is the carrier.
In other words, FM affects the timbre of Oscillator 2, and
does not affect the timbre of Oscillator 1.
You can create stable, periodic waveforms by setting FM
Amount to any multiple of 6, such as 6, 12, 18, 24, etc. At
other settings, the signal will "roll around" in interesting
ways.
This feature is similar to a classic five-voice analog
synthesizer's "Osc B to Freq A" function, except that the
depth can be up to eight times greater–16 octaves instead of
2.
To create a cool sync-like sound with FM:
1. Set Oscillator 1's Waveform to Pulse.
2. Assign an AMS source, such as an EG or LFO, to
modulate Oscillator 1's Pulse Width.
3. Set Oscillator 2's Waveform to Pulse.
4. Set Oscillator 2's Pulse Width to 50.
5. Set the FM amount to 24.
194
[–12...+12]
[–1200...+1200]
[-10.0Hz ... +10.0Hz]
[000...100]
Note also that FM, Sync, and Ring Mod can all be used
simultaneously.
AMS
This selects an AMS source to control the FM Amount. For
a list of AMS sources, see "Alternate Modulation Source
(AMS) List" on page 1109.
Intensity
This controls the depth and direction of the FM Amount
AMS modulation.
Sync
When Sync is On, Oscillator 1 controls the pitch of
Oscillator 2, and changing or modulating Oscillator 2's
frequency changes its timbre, instead of its pitch.
Every time that Oscillator 1 begins a new cycle (the instant
that it passes through zero going from negative to positive),
Oscillator 2 snaps back to the start of its waveform.
Note that FM, Sync, and Ring Mod can all be used
simultaneously.
To create the classic sync sweep sound:
1. Turn Sync On.
2. Assign an EG as the AMS source for Oscillator 2
Pitch.
3. Now, the EG is controlling the sync sound.
4. Set the EG and Pitch AMS Intensity parameters to
create the desired sync sweep.
4–1d: Edge (OSC 1, OSC 2 & Sub OSC)
Edge
This controls the high-frequency character of Oscillator 1,
Oscillator 2, and the Sub Oscillator.
Set it to 0 for a timbre similar to vintage American analog
synths, and to higher values for "edgier" tones.
Negative values result in warmer, darker tones, to create an
oscillator timbre similar to the MS-20.
v 4–1: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see "ENTER + 0-9: shortcuts for menu
commands" on page 153.
• 0: Write Program. For more information, see "Write
Program" on page 153.
• 1: Exclusive Solo. For more information, see "Exclusive
Solo" on page 153.
[List of AMS Sources]
[–100...+100]
[Off, On]
[–100...+100]