Korg KRONOS SGX-2 Parameter Manual page 62

Program mode: HD-1
Play/Mute
This determines whether or not the Drum Track Program
will sound. The setting will alternate each time you press the
Play/Mute button.
Mute: The timbre will not sound.
Play: The timbre will sound.
You can also adjust this from the Control Surface, using Mix
Play/Mute button 3 in Timbre/Track mode.
1–3c: Trigger
Mode [Start Immediately, Wait KBD Trig]
This controls how the pattern will start and stop.
Start Immediately: When you turn on the Drum Track by
pressing the DRUM TRACK switch, the LED will light and
the Drum Track pattern will start according to the Sync
setting. It will stop when you turn off the switch.
Wait KBD Trig: When you press the DRUM TRACK
switch to turn it on, the LED will blink and the Drum Track
pattern will wait to start. When you play the keyboard or
receive a MIDI note-on, the Drum Track pattern will start
according to the Sync setting.
The Mode setting also affects the way in which the on/off
status of the DRUM TRACK switch is stored.
With Wait KBD Trig, the on/off status of the DRUM
TRACK switch is also saved when you save the Program.
With Start Immediately, the switch status is always saved
as Off, regardless of the whether the switch is on or off when
you Write.
Latch [On, Off, Use KARMA Latch Switch]
Latch controls whether the Drum Track pattern will
continue playing even after you take your hands off of the
keyboard. This applies when the Trigger Mode is set to
Wait KBD Trig.
Off: If the DRUM TRACK switch is on, the LED will blink,
and the pattern will start when you play the keyboard. When
you stop playing, the Drum Track will stop as well.
On: If the DRUM TRACK switch is on (the LED will
blink), the pattern will start when you play the keyboard
(note-on). The pattern will continue when you release the
keyboard (note-off). The pattern will stop when you turn the
DRUM TRACK switch off (the LED will go dark).
Use KARMA Latch Switch: The on/off status of the
KARMA LATCH switch will correspond to the above Off
and On modes of operation. You will probably want to use
this in conjunction with KARMA's Latch operation.
Sync
If you want the Drum Track pattern to play in sync with
KARMA (or with the Sequencer, in Sequencer mode), turn
Trigger Sync on.
Trigger Sync On: The Drum Track's start will synchronize
to the currently-playing KARMA pattern, quantized to the
nearest beat. In Sequencer mode, triggering will synchronize
to the currently-playing song, pattern or RPPR performance,
quantized to the nearest measure.
48
[Mute, Play]
Note: If you want to synchronize KARMA to the Drum
Track, enable the Quantize Trig parameter (Prog P7:
KARMA– Trigger, Combi/Seq P7: KARMA Module
Parameters-Trigger).
Note: In Sequencer mode, if you want to synchronize
the RPPR pattern performance to the currently-
running Drum Track, set the Sync parameter to Beat or
Measure.
Trigger Sync Off: If the Trigger Mode is set to Start
Immediately, the Drum Track pattern will be triggered the
moment you press the DRUM TRACK switch. If this is set
to Wait KBD Trig, the Drum Track pattern will be triggered
the moment you play the keyboard. It will not synchronize to
the currently-playing KARMA pattern or (in Sequencer
mode) to the currently-playing song, pattern, or RPPR.
1–3d: Keyboard Trigger Zone
These settings specify the range of keys and velocities that
will trigger the Drum Track pattern when you play the
keyboard (or the system receives a note-on via MIDI).
Keyboard Top
Specifies the highest note that will trigger the Drum Track
Pattern.
Bottom
Specifies the lowest note that will trigger the Drum Track
Pattern.
Velocity Top
Specifies the maximum velocity value that will trigger the
Drum Track Pattern.
Bottom
Specifies the minimum velocity value that will trigger the
Drum Track Pattern.
Key and Velocity settings can also be edited by holding
down the ENTER switch and playing on the keyboard.
The Keyboard and Velocity Top settings must be higher
than their respective Bottom settings.
1–3e: EQ
This 3-band EQ is dedicated to the Drum Track Program,
and is completely separate from the main Program's EQ.
Auto Load Program EQ
On (checked): When you change the drum track Program,
the new Program's EQ values will be copied automatically.
This setting is the default.
[On, Off]
After the Program is loaded, you can still edit the EQ
settings as desired.
Off (unchecked): Newly selected Drum Track Program's
EQ settings will not replace the current EQ settings. Use this
if you've edited the EQ settings, and want to keep them
constant while listening to different Drum Track Programs.
Bypass
When Bypass is checked, all of the EQ will be disabled,
including the Input Trim.
Bypass can be convenient for comparing the results of the
EQ with the original signal.
[C–1...G9]
[C–1...G9]
[1...127]
[1...127]
[On, Off]
[On, Off]