Korg KRONOS SGX-2 Parameter Manual page 827

5–3b: Mixer
Drum kits will sound using the settings of the program
that is selected in Program mode. Pan is valid if "Use
DKit Setting" (Program 4–1c) is checked. Bus Select, FX
Control Bus, and "Send 1/2" are valid if "Use DKit
Setting" (Program 8–1b) is checked. Be aware that while
editing a drum kit, the edited results will not be reflected
unless these settings have been made.
Bus Select (IFX/Indiv.Out Assign)
[L/R, IFX1...12, 1...4, 1/2...3/4, Off]
For each key, you can specify the bus to which the sound
will be sent.
For example, you might send Snare sounds to IFX1 and Kick
sounds to IFX2 to apply separate insert effects, and send the
remaining sounds to L/R without applying insert effects.
Tip: In most of the preloaded drum kits, the following types
of drum instrument have the same Bus Select settings.
Tip: Most of the preloaded drum kits use the same basic Bus
Select settings, as shown below:
Snares IFX1
Kicks IFX2
Toms IFX3
Cymbals IFX4
Percussion etc. IFX5
FX Control Bus
For each key, you can select whether the signal will be sent
to FX Control bus (stereo two-channel) FX Ctrl1 or 2.
Gated Reverb Example
Global P5: Drum Kit
KEY: D3
(Snare)
Pan [Random, L001...C064...R127]
Specifies the panning for each key.
L001 places the sound at far left, and R127 places the signal
at far right. With a setting of Random, the drum sample will
be panned randomly at each note-on.
Send1 (to MFX1)
Send2 (to MFX2)
For each key, specify the send levels to master effects 1 and
2.
These settings are valid when Bus Select (5–3b) is set to L/R
or Off. If Bus Select is set to IFX1–12, the send level to
master effects 1 and 2 will be determined by the Program,
Combination, or Sequencer mode P8: Insert FX page
parameters Send1 and Send2 which are located after the
sound passes through IFX1–12.
[Off, 1, 2]
IFX6
Bus Select
: IFX6
101: Reverb Hall
FX Control Bus: 1
(FX Control Bus1)
[000...127]
[000...127]
Global P5: Drum Kit 5–3: Voice Assign/Mixer
Normally you will leave this off, but you can use this setting
if you want to control an effect by playing a specific key.
You can use this with the following effects:
Vocoders:
• 026: Vocoder
Compressor and gate-type effects:
• 002: Stereo Compressor
• 003: Stereo Expander
• 005: Stereo Limiter
• 009: Stereo Gate
• 010: Stereo Noise Reduction
Example: Gated Reverb
This is an example of applying a gated reverb to only a
specific snare sound. When using a gate effect on reverb,
you may not be able to control the gating timing correctly if
you use the extended reverberant sound to control the gate.
Normally, you will control the gate using sound from before
reverb is applied.
For the key for which you've selected the snare sample, set
Bus Select to IFX6. Also use FX Control Bus Select to
send the signal to FX Control Bus 1. In IFX7: Stereo Gate,
choose FX Control 1 as the Envelope Source. Now you can
use a signal other than the input (reverberant sound) to
control the gate.
Program P4, P8: Use DKit Setting = On
IFX7
Chain to
: IFX7
009: Stereo Gate
Envelope Source
: FX Control 1
v 5–3: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see "ENTER + 0-9: shortcuts for menu
commands" on page 153.
• 0: Write Drum Kit. For more information, see "Write
Drum Kit" on page 824.
• 1: Copy Key Setup. For more information, see "Copy
Key Setup" on page 824.
• 2: Swap Key Setup. For more information, see "Swap
Key Setup" on page 824.
Bus Select
: L/R
813