Table of Contents
Advertisement
Global mode
Local Control On = On
You can also use MIDI input to trigger KARMA. For
instance, you can control KARMA from an external
controller. Or, use an external sequencer to record only the
notes you physically play on the KRONOS keyboard (and
not KARMA's generated events), and then play them back to
trigger KARMA in real-time.
To do so, use the Trigger KARMA generation from
external device/sequencer option in the Setup KARMA
External MIDI Routing menu command, or make the
following settings manually:
Enable KARMA Module to MIDI Out = Off
Enable MIDI In to KARMA Module = On
Local Control On = Off
Start/Stop (Realtime) Out
Enable Start/Stop Out in Prog/Combi
In Program and Combination modes, this function transmits
a MIDI start message when you trigger KARMA, and a
MIDI stop message when you turn it off. This lets you make
an external MIDI sequencer or rhythm/groove machine start
playing at the moment that KARMA begins playing.
Off (unchecked): Normally you will leave this Off.
On (checked): MIDI system realtime messages "Start" and
"Stop" will be transmitted in Program and Combination
mode. If MIDI Clock (1–1a) is set to Internal or Auto (and
operating as Internal), the start and stop messages will be
transmitted under the conditions described below. This can
be used to simultaneously start an external MIDI sequencer
or rhythm/groove machine at the moment KARMA begins
playing.
Start: If the KARMA ON/OFF switch is on, the MIDI
system realtime message "Start" will be transmitted at the
moment you use the keyboard to trigger the GE.
Note: "Start" will be transmitted at the moment that the GE
phrase or pattern is triggered, according to the module's
"KARMA Key Zone" setting (Program 7–1a, Combination
7–1b).
Stop: If "Start" has been previously transmitted, the MIDI
system realtime message "Stop" will be transmitted at the
moment you turn off the KARMA ON/OFF switch.
For more information, see "Connecting MIDI devices &
computers" on page 1143, "Synchronizing the playback of
KARMA or sequencer" on page 1154, and "Synchronizing
KARMA" on page 255 of the Operation Guide.
786
[Off, On]
Clock: External
MIDI IN
"MIDI Clock": Internal
"Enable Start/Stop Out
MIDI OUT
in Prog/Combi": On
1–1c: MIDI Filter
Enable Program Change
On (checked): Program changes will be transmitted and
received.
In Program mode (P0: Play), the program will be switched
when a program change message is received on the global
MIDI channel specified by MIDI Channel (1–1a). When
you switch programs, a program change message will be
transmitted on the global MIDI channel.
In Combination mode (P0: Play), the combination will be
switched when a program change message is received on the
global MIDI channel. However, it is possible to set the
"Enable Combination Change" parameter so that the
combination is not switched. When a program change is
received on the channel specified for each timbre by MIDI
Channel (Combination 2–1a), the program of that timbre
will be switched. However, the program changes for each
timbre will be affected by the setting of the "Enable Program
Change" parameter (Combination 3–1a).
When you switch combinations, a program change message
will be transmitted on the global MIDI channel, and also
transmitted simultaneously on the channel of timbres whose
Status (Combination 0–1b, 2–1a) is set to EXT or EX2.
In Sequencer mode, incoming program change messages on
a channel that corresponds to a track whose Status
(Sequencer 2–1a) is set to INT or BTH will switch programs
on that track. When you select a song or playback sequencer
data, program changes will be transmitted on the channels of
tracks whose Status is set to BTH, EXT, or EX2.
In Set List mode (P0: Play), the slot will be switched when a
program change message is received on the global MIDI
channel. When you switch slots, a program change message
will be transmitted on the global MIDI channel. If the Slot
contains a Combination or Song, other program change
messages may be transmitted on additional MIDI channels,
as would normally occur in Combination or Sequencer
modes.
Off (unchecked): Program changes will not be transmitted
or received.
Bank Change
On (checked): The Bank Select control change message
will be transmitted together with program change messages.
This is valid when "Enable Program Change" is checked.
Off (unchecked): Bank Select messages will not be
transmitted or received.
When recording on the internal sequencer, bank select
messages will be recorded regardless of this setting.
However for playback, this setting will apply.
This also controls send and receive of Bank Select messages
for Set List selection in Set List mode.
Combination Change
On (checked): When in Combination P0: Play, an incoming
program change message on the global MIDI channel set by
MIDI Channel (1–1a) will switch Combinations.
This is valid when "Enable Program Change" is checked.
An incoming program change on a channel other than the
global MIDI channel will switch the program of any timbre
that matches that MIDI channel.
[Off, On]
[Off, On]
[Off, On]
Advertisement
Table of Contents
