Korg KRONOS SGX-2 Parameter Manual page 779

With a setting of PostMIDI, variations in after touch
pressure (and in the value of incoming after touch data) will
create change as shown in the right-hand diagram.
For the transmitted data, the after touch curve number 3
shown in the left-hand diagram will automatically be
selected.
Convert Position = PreMIDI
After Touch (KBD to MIDI Out)
127
8:RANDOM
5
4
3
7
2
6
1
0
Soft Strong
1, 2: This curve produces change when strong after touch
pressure is applied
3 (Normal): The normal curve
4, 5: This curve produces change even when light pressure is
applied
6, 7: These curves produce change in 24 or 12 steps
respectively, and are appropriate for when you are recording
after touch data on the sequencer and wish to conserve
memory. (Set the Convert Position to PreMIDI in order to
record the results.) Curve number 7 allows change over
twelve steps, so when using after touch to modify the pitch,
you can set the range of modification to one octave, and use
after touch to vary the pitch in semitone steps.
8: This is a random curve. Use this when you wish to create
special effects, or to use after touch to apply unpredictable
modulation.
When Convert Position (1–1a) is PreMIDI, the setting
you make here will be applied immediately after the
keyboard, meaning that it will affect the data transmitted
via MIDI, but will not affect the received data.
With a setting of PostMIDI, the setting you make here
will be applied immediately before the KRONOS's
internal tone generator, meaning that it will affect the data
received via MIDI, but will not affect the transmitted
data.
When you use the KRONOS's keyboard to play the
internal sounds, the Convert Position setting has no
effect.
KRONOS2-88LS
The KRONOS2-88LS keyboard does not generate
aftertouch, and so the Convert Position setting PreMIDI
does not apply. The After Touch Curve is always applied
immediately before the tone generator; it affects received
MIDI data, but does not affect transmitted MIDI data.
After Touch (MIDI In→TG)
MAX
5
After
Touch
7
効果
0
Convert Position = PostMIDI
After Touch (MIDI In to Sound Engine)
MAX
5
Aftertouch
4
effect
7
3
2
6
8:RANDOM
1
0 127
4
3
2
8:RANDOM
6
1
127
Global P0: Basic Setup 0–1: Basic Setup
0–1b: Effect Global SW
IFX1–12 Off
On (checked): All insert effects IFX1–12 will be off.
Off (unchecked): The P8: Insert Effect settings for IFX1
On/Off–IFX12 On/Off in Program, Combination,
Sequencer, and Sampling modes will be valid.
MFX1&2 Off
On (checked): Master Effect1 and 2 (MFX1, 2) will be off.
Off (unchecked): The P9: Master/Total Effect setting
MFX1 On/Off, and MFX2 On/Off, in Program,
Combination, and Sequencer modes will be valid.
TFX1&2 Off
On (checked): Total effects 1 and 2 (TFX1, 2) will be off.
Off (unchecked): The TFX1 On/Off and TFX2 On/Off
settings in the P9: Master/Total Effect page of Program,
Combination, Sequencer, or Sampling modes will be used.
When IFX1–12 On/Off, MFX1&2 On/Off, or TFX1&2
On/Off settings are switched, control change messages
CC#92 (effect control 2), CC#94 (effect control 4), and
CC#95 (effect control 5) will be transmitted respectively.
The transmitted data will be 0 for off, and 127 for on.
0–1c: KARMA
All KARMA Off
On (checked): All KARMA functionality will be disabled.
KARMA will not play even if the KARMA ON/OFF switch
is on.
Off (unchecked): KARMA will play normally, based on the
DRUM TRACK switch setting.
Drum Track Off
On (checked): All Drum Track functionality will be
disabled. The Drum Track will not play even if the DRUM
TRACK switch is on.
Off (unchecked): The Drum Track will play normally,
based on the DRUM TRACK switch setting.
Load KARMA settings when changing
Programs
On (checked): When you switch programs, the KARMA
Module settings stored in that program will be used.
Normally you will use the On setting.
Off (unchecked): The KARMA Module settings will not
change even if you switch programs. Use this setting if you
want to switch Program sounds without changing the
phrases from the KARMA Modules.
Combinations
On (checked): When you switch Combinations, the
KARMA Module settings stored in that Combination will be
used. Normally you will use the On setting.
Off (unchecked): The KARMA Module settings will not
change even if you switch Combinations. Use this setting if
you want only to switch the sound of the Combination,
without changing the phrases from the KARMA Modules.
[Off, On]
[Off, On]
[Off, On]
[Off, On]
[Off, On]
[Off, On]
[Off, On]
765