Table of Contents
Advertisement
Program mode: HD-1
Single EXi Programs will use the default assignments for
their EXi. Assignments for double EXi Programs are
turned Off except for the EXi Common parameters.
For details on the default Tone Adjust assignments, see:
• "HD-1 Tone Adjust Parameters" on page 38
• "AL-1: Tone Adjust" on page 228
• "CX-3: Tone Adjust" on page 251
• "STR-1: Tone Adjust" on page 300
• "MS-20EX: Tone Adjust" on page 327
• "PolysixEX: Tone Adjust" on page 342
• "MOD-7: Tone Adjust" on page 393
• "SGX-2: Tone adjust" on page 404
• "EP-1: Tone Adjust" on page 423
3. To execute the Reset Tone Adjust command, press the
OK button. To exit without resetting the assignments,
press the Cancel button.
Copy Oscillator
Copy Oscillator is available on all of the tabs under the
Basic/Vector, OSC/Pitch, Filter, Amp/EQ, and AMS
Mix/Common Key Track pages.
This command is used to copy the settings from one
oscillator to another.
1. Select "Copy Oscillator" to open the dialog box.
2. Use the "From" field to select the oscillator that you
want to copy.
3. Use "Program" to select the bank and number of the
copy-source program. You can press a BANK
SELECT switch to select the desired bank.
Note: If you're editing an HD-1 Program, you can't select
EXi Programs, and vice-versa.
4. If you check "Tone Adjust too," the Tone Adjust
settings will temporarily be turned off, and from the
copy-source Tone Adjust settings, the Common
portion and the assignments and current values of the
corresponding OSC portion will be copied.
If "Tone Adjust too" is unchecked, the Tone Adjust
settings will be maintained.
5. In "To," specify the copy destination oscillator.
6. To execute the Copy Oscillator command, press the
OK button. To cancel, press the Cancel button.
160
Swap Oscillator
Swap Oscillator is available on all of the tabs under the
Basic/Vector, OSC/Pitch, Filter, Amp/EQ, and AMS
Mix/Common Key Track pages.
This command exchanges the settings of oscillators 1 and 2.
1. Select "Swap Oscillator" to open the dialog box.
2. To execute the Swap Oscillator command, press the
OK button. To cancel, press the Cancel button.
This can be selected only if Oscillator Mode (1–1a) is
Double.
Copy Vector Envelope
Copy Vector Envelope is available on the Vector Envelope
tab of the Basic/Vector page.
This command copies vector envelope settings from the
specified program, combination/timbre, or song.
1. Select "Copy Vector Envelope" to open the dialog box.
2. Use the "From" field to select the mode, bank, and
number of the desired copy-source. You can press a
BANK key to select the desired bank.
This command copies the parameters of the P1-Vector
Envelope page of the corresponding mode.
Note: In order to replicate the way in which the relative
volume of oscillators is controlled by the vector and
vector envelope of the program selected for a
combination timbre or a MIDI song track, turn on the
Enable Program Vector Volume check box in the Vector
Control Volume page. To replicate the CC control effects,
turn on the Enable Program Vector CC check box in the
Vector Control CC page.
Use this command when you want to copy the Position or
Time/Tempo of a vector envelope in order to create an
envelope that produces the same movement.
3. Press the OK button to execute the command, or press
the Cancel button to cancel.
Copy Pad Setup
Copy Pad Setup is available on the Pads tab of the
Basic/Vector page.
This command copies the pad settings of the specified
Program, Combination, or Song.
1. Select Copy Pad Setup to open the dialog box.
Advertisement
Table of Contents
