ABB IRB 6620 Product Manual page 6

Table of contents
2.7 Foundry Plus Cable guard (option) .......................................................................
2.7.1 Installation of Foundry Plus Cable guard (option no. 908-1) .............................
2.8 Electrical connections ........................................................................................
2.8.1 Robot cabling and connection points ..........................................................
2.9 Start of robot in cold environments ......................................................................
3 Maintenance
3.1 Introduction ......................................................................................................
3.2 Maintenance schedule and expected component life ...............................................
3.2.1 Specification of maintenance intervals ........................................................
3.2.2 Maintenance schedule .............................................................................
3.2.3 Expected component life .........................................................................
3.3 Inspection activities ...........................................................................................
3.3.1 Inspecting the oil level in axis-1 gearbox .....................................................
3.3.2 Inspecting the oil level in axis-2 gearbox .....................................................
3.3.3 Inspecting the oil level in axis-3 gearbox .....................................................
3.3.4 Inspecting the oil level in axis-4 gearbox .....................................................
3.3.5 Inspecting the oil level in axis-5 gearbox .....................................................
3.3.6 Inspecting the oil level in axis-6 gearbox .....................................................
3.3.7 Inspecting, cable harness ........................................................................
3.3.8 Inspecting the information labels ................................................................
3.3.9 Inspecting the axis-1 mechanical stop pin ...................................................
3.3.10 Inspecting the additional mechanical stops .................................................
3.3.11 Inspecting the damper on axes 2-5 .............................................................
3.3.12 Inspecting, signal lamp ............................................................................
3.3.13 Inspection of air hoses (Foundry Prime) ......................................................
3.4 Replacement/changing activities ..........................................................................
3.4.1 Type of lubrication in gearboxes ................................................................
3.4.2 Changing oil, axis-1 gearbox .....................................................................
3.4.3 Changing oil, axis-2 gearbox .....................................................................
3.4.4 Changing oil, axis-3 gearbox .....................................................................
3.4.5 Changing oil, axis-4 gearbox .....................................................................
3.4.6 Changing oil, axis-5 gearbox .....................................................................
3.4.7 Changing oil, axis-6 gearbox .....................................................................
3.4.8 Replacing the SMB battery ........................................................................
3.5 Cleaning activities .............................................................................................
3.5.1 Cleaning the IRB 6620 ..............................................................................
4 Repair
4.1 Introduction ......................................................................................................
4.2 General procedures ...........................................................................................
4.2.1 Performing a leak-down test ......................................................................
4.2.2 Mounting instructions for bearings .............................................................
4.2.3 Mounting instructions for seals ..................................................................
4.2.4 Cut the paint or surface on the robot before replacing parts ............................
4.2.5 The brake release buttons may be jammed after service work .........................
4.3 Complete robot .................................................................................................
4.3.1 Replacement of cable harness, lower end (axes 1-2) ......................................
4.3.2 Replacement of cable harness, upper end ...................................................
4.3.3 Replacement of complete arm system .........................................................
4.4 Upper and lower arm .........................................................................................
4.4.1 Replacing the turning disk ........................................................................
4.4.2 Replacement of wrist unit .........................................................................
4.4.3 Replacement of the upper arm ...................................................................
4.4.4 Replacement of lower arm ........................................................................
4.5 Frame and base ................................................................................................
4.5.1 Replacement of SMB unit .........................................................................
4.5.2 Replacing the brake release board .............................................................
6
© Copyright 2006-2018 ABB. All rights reserved.
111
111
112
112
114
115
115
116
116
117
119
120
120
122
125
127
129
131
134
137
139
141
144
146
148
149
149
151
154
157
160
163
166
169
173
173
177
177
178
178
179
181
183
184
185
185
192
202
213
213
217
222
228
233
233
238
Product manual - IRB 6620
3HAC027151-001 Revision: T