About This User's Guide Intended Audience This manual is intended for people who want to configure the IES-612-51A using the web configurator. You should have at least a basic knowledge of TCP/IP networking concepts and topology. Related Documentation • Quick Start Guide The Quick Start Guide is designed to help you get up and running right away.
Syntax Conventions • The IES-612-51A may be also referred to as the “device”, the “system” or the “product” in this User’s Guide. • Product labels, screen names, field labels and field choices are all in bold font.
Page 5
Icons Used in Figures Figures in this User’s Guide may use the following generic icons. The IES-612-51A icon is not an exact representation of your IES-612-51A. IES-612-51A Server Telephone IES-612-51A User’s Guide Computer Notebook computer DSLAM Firewall Switch Router Document Conventions...
• Fan Module Warning! Use the fan module handle when pulling out or pushing in the fan module. Be careful not to put fingers or objects inside the fan module. This product is recyclable. Dispose of it properly. Safety Warnings IES-612-51A User’s Guide...
Introduction ... 39 Getting to Know the IES-612-51A ... 41 Hardware Installation ... 45 Front Panel ... 49 Basic Settings ... 59 Introducing the Web Configurator ... 61 Initial Configuration ... 69 Home and Port Statistics Screens ... 75 System Information ... 87 General Setup ...
Page 30
Figure 163 MAC Filter Disable Command Example ... 308 Figure 164 MAC Filter Mode Command Example ... 309 Figure 165 MAC Filter Set Command Example ... 309 Figure 166 MAC Filter Delete Command Example ... 309 Figure 167 MAC Count Show Command Example ... 310 IES-612-51A User’s Guide...
Page 31
Figure 199 FTP Put Configuration File Example ... 335 Figure 200 FTP Get Configuration File Example ... 336 Figure 201 Example: Use an FTP Client to Connect to the IES-612-51A ... 337 Figure 202 Example: Enter the Management Password ... 337 Figure 203 Example: Get the Configuration File config-0 ...
Page 32
Figure 249 Line Diagnostics Get 992.3 Command Example ... 366 Figure 250 SELT Diagnostic Set Command Example ... 367 Figure 251 Line Diagnostics Get Command Example ... 368 Figure 252 Tone Diagnostics Command Example ... 369 Figure 253 Alarm Profile Show Command Example ... 370 IES-612-51A User’s Guide...
Page 33
Figure 292 ACL Assignment Set Command Example ... 402 Figure 293 ACL Assignment Show Command Example ... 403 Figure 294 Testing In-house Wiring ... 410 Figure 295 Resetting the Switch Via Command ... 413 Figure 296 Example Xmodem Upload ... 414 IES-612-51A User’s Guide...
Page 34
List of Figures Figure 297 Example Xmodem Upload ... 415 Figure 298 Telco-50 Pin Assignments ... 425 Figure 299 Console Cable RJ-11 Male Connector ... 426 Figure 300 Console Cable DB-9 Female Connector ... 426 IES-612-51A User’s Guide...
12 ADSL lines to two Ethernet ports to connect ADSL subscribers to the Internet. You can use the built-in web configurator to manage and configure the IES-612-51A. In addition, the IES-612-51A can also be managed via Telnet, the console port, or third-party SNMP management.
Figure 1 MTU Application 1.2.2 Curbside Application The IES-612-51A can be used by an Internet Service Provider (ISP) in a street cabinet to form a "mini POP (Point-of-Presence)" to provide broadband services to residential areas that are too far away from the ISP to avail of DSL services. Residents need a DSL modem, connected as shown in the previous figure.
Section 34.3 on page 1.4 Good Habits for Managing the IES-612-51A Do the following things regularly to make the IES-612-51A more secure and to manage the IES-612-51A more effectively. • Change the password. Use a password that’s not easy to guess and that consists of different types of characters, such as numbers and letters.
Page 44
Chapter 1 Getting to Know the IES-612-51A IES-612-51A User’s Guide...
2.2.1 Desktop Installation Procedure Do the following to install the IES-612-51A on top of a desk or table. The figures in this section are examples and are not intended as an exact representation of the IES-612-51A. 1 Make sure the IES-612-51A is clean and dry.
2.2.2 Rack-Mounted Installation 2.2.2.1 Rack-mounted Installation Requirements The IES-612-51A can be mounted on an EIA standard size, 19-inch rack or in a wiring closet with other equipment. Follow the steps below to mount your IES-612-51A on a standard EIA rack using a rack-mounting kit.
Do the following to rack-mount the IES-612-51A. The figures in this section are examples and are not intended as an exact representation of the IES-612-51A. 1 Align one bracket with the holes on one side of the IES-612-51A and secure it with the bracket screws smaller than the rack-mounting screws.
H A P T E R This chapter describes the front panel and rear panel of the IES-612-51A and shows you how to make the hardware connections. 3.1 Front Panel The figure below shows the front panel of the IES-612-51A.
• No parity, 8 data bits, 1 stop bit • No flow control Connect the male 9-pin end of the console cable to the console port of the IES-612-51A. Connect the female end to a serial port (COM1, COM2 or other COM port) of your computer.
3.2.2 LAN Port (Ethernet) Connection Connect the LAN port of your IES-612-51A to an Ethernet WAN switch using a straight- through Category 5 UTP (Unshielded Twisted Pair) cable with RJ-45 connectors. You may connect multiple IES-612-51A units to the same Ethernet switch (up to the number of ports available on the Ethernet switch).
3.2.5 Telco-50 Connections The internal DSL splitters separate the voice signals from the DSL signals. They feed the DSL signals to the IES-612-51A and divert the voice signals to the CO lines of the Telco-50 connector. Connect the CO lines of the Telco-50 connector to the PBX or PSTN/ISDN switch.
This section describes typical installation scenarios. 3.2.7.1 Installation Scenario A You want to install the IES-612-51A in an environment where there are no previously installed MDFs. There is no phone service and you want to install the IES-612-51A for data-access only.
3 Connect the telephone wiring from each end-user's DSL modem to the lower ports of the MDF. 3.2.7.2 Installation Scenario B Phone service is available. There is one MDF from which end-users CO connections are made (see next figure). IES-612-51A User’s Guide...
• MDF 2 is used for telephone connections only. • MDF 3 is for ADSL service connections. Change the wiring (in the following figure) from MDF 1 to MDF 3 for telephone subscribers who want ADSL service. IES-612-51A User’s Guide Chapter 3 Front Panel...
8 Change the wiring from MDF 1 to MDF 3 for telephone subscribers who want DSL service. 3.2.7.3 Installation Scenario C Phone service is also available but there are two MDFs; one for end-user telephone line connections and the other one for CO telephone wiring connections (see the following figure). IES-612-51A User’s Guide...
• MDFs 1 and 2 are the two original MDFs. • MDFs 3 and 4 are two additional MDFs you need. User A still has telephone service only. User B now has telephone and DSL service (see the following figure). IES-612-51A User’s Guide Chapter 3 Front Panel...
5 Connect the CO wiring of the Telco-50 cable to the lower ports of MDF 4 using a punch- down tool. 6 Connect the top ports of MDF 4 to the bottom ports of MDF 1 using telephone wires. 7 Connect the top ports of MDF 1 to the telephone company. IES-612-51A User’s Guide...
Basic Settings Introducing the Web Configurator (61) Initial Configuration (69) Home and Port Statistics Screens (75) System Information (87) General Setup (91) User Account (93) Switch Setup (97) IP Setup (103) ENET Port Setup (105) xDSL Port Setup (107) xDSL Profiles Setup (125) xDSL Line Data (137)
This chapter tells how to access and navigate the web configurator. 4.1 Web Configurator Overview The web configurator allows you to use a web browser to manage the IES-612-51A. 4.2 Screen Privilege Levels There is a high or low privilege level for each screen.
B - Click this to open the Home screen. (This is the same screen that is displayed above.) See Chapter 6 on page 75 for more information. C - Click this to log out of the web configurator. IES-612-51A User’s Guide...
Use this screen to configure system administrator accounts. Switch Setup Use this screen to set up system-wide parameters such as MAC address learning and priority queues. IES-612-51A User’s Guide Chapter 4 Introducing the Web Configurator ADVANCED APPLICATION MANAGEMENT ROUTING PROTOCOL...
Page 64
Use these screens to drop traffic from IP addresses not assigned by the DHCP server and to look at a summary of the DHCP packets on each port. Use this screen to configure the IES-612-51A to handle 2684 routed mode traffic.
Config Save Config Save Use this screen to save the device’s configuration into the nonvolatile memory (the IES-612-51A’s storage that remains even if the IES-612-51A’s power is turned off). 4.5 Changing Your Password After you log in for the first time, it is recommended you change the default administrator password.
IES-612-51A’s power is turned off. Click Config Save in the navigation panel to save your configuration to nonvolatile memory. Nonvolatile memory refers to the IES-612-51A’s storage that remains even if the IES-612- 51A’s power is turned off. Use Config Save when you are done with a configuration session.
H A P T E R This chapter describes initial configuration for the IES-612-51A. See for various default settings of the IES-612-51A. 5.1 Initial Configuration Overview This chapter shows what you first need to do to provide service to DSL subscribers.
A channel that is not the super channel can only forward frames with a single VLAN ID (that is configured on that channel). In this case, the IES-612-51A drops any frames received from the subscriber that are tagged with another VLAN ID.
Leave the other default settings, and click Add. The VC Setup screen is updated. Figure 26 VC Setup 11 Select the new channel’s Select radio button. Click Copy, and then click Paste. The following screen appears. The following screen appears. IES-612-51A User’s Guide...
12 Click All, and then click Apply. The VC Setup screen is updated. Figure 28 VC Setup 13 Click Config Save, Config Save. The Config Save screen appears. Figure 29 Config Save 14 Click Save. The following screen should appear. IES-612-51A User’s Guide Chapter 5 Initial Configuration...
Figure 30 Config Save, Save Successful You can now use the device (with the other settings set to the defaults) to provide service to DSL subscribers. See Section 56.4 on page 423 for information on other default settings. IES-612-51A User’s Guide...
The Status This field displays whether the Ethernet port is connected (Up) or not (Down). Port Name This field displays the name of the Ethernet port. IES-612-51A User’s Guide Ethernet Port Statistics Screen Section 6.1.1 on page Screens appears.
Select a port from the Port drop-down list box and then click Clear Counter to erase the recorded statistical information for that port. Click this to set the Poll Interval(s) and Port fields to their default values and to refresh the screen. appears. See Section 6.1.2 on page IES-612-51A User’s Guide...
This field shows the number of good broadcast frames received of 64 to 1518 octets in length (for non VLAN) or 1522 octets (for VLAN), not including multicast frames. Frames with range or length errors are also not taken into account. IES-612-51A User’s Guide Chapter 6 Home and Port Statistics Screens...
Page 78
64 octets or less in length (this includes FCS octets but excludes framing bits). This field shows the number of frames received and transmitted (including bad frames) that were 65 to 127 octets in length (this includes FCS octets but excludes framing bits). IES-612-51A User’s Guide...
6.1.2 DSL Port Statistics Screen Use this screen to display statistics about a DSL port. To open this screen, click a DSL port’s number in the Home screen. IES-612-51A User’s Guide Chapter 6 Home and Port Statistics Screens...
This field shows the number of broadcast packets received on this port. This field shows the number of outgoing packets that were dropped on this port. The “Tx discard packets” counter always displays “0” because the IES-612-51A does not discard packets that it sends.
Chapter 6 Home and Port Statistics Screens The packet filter is enabled and the packets matched a packet filter. The MAC filter is enabled and the IES-612-51A dropped the packets according to the MAC filter’s configuration. The packets contained frames with an invalid VLAN ID.
This field displays the total number of multicast packets received/ transmitted on this port. This field displays the total number of CRC (Cyclical Redundancy Check) alignment errors on this port. This field displays the total number of packets that were too small received/transmitted on this port. IES-612-51A User’s Guide...
6.1.4 RMON History Screen Use this screen to display general information (such as sample time) on history samples. To open this screen, click any port number in the RMON Statistics screen. IES-612-51A User’s Guide Chapter 6 Home and Port Statistics Screens DESCRIPTION This field displays the total number of packets that were too big received/transmitted on this port.
This field displays the number of broadcast packets received or transmitted since the last sample time. This field displays the number of multicast packets received/transmitted since the last sample time. This field displays the port utilization status. IES-612-51A User’s Guide...
Fragments This is the number of frames received/transmitted that were less than 64 octets long, and contained an invalid FCS, including non-integral and integral lengths. IES-612-51A User’s Guide Chapter 6 Home and Port Statistics Screens...
Page 86
This is the number of frames for which transmission failed due to excessive collisions. Excessive collision is defined as the number of maximum collisions before the retransmission count is reset. This field displays the port utilization status in the sampling period. IES-612-51A User’s Guide...
(such as temperature status). You can check the firmware version number and monitor the hardware status in this screen. To open this screen, click Basic Setting, System Information. Figure 37 System Info IES-612-51A User’s Guide System Information...
Configure new threshold settings in the fields below and click Apply to use them. Use these fields to configure the highest temperature limit at each sensor. Use these fields to configure the lowest temperature limit at each sensor. IES-612-51A User’s Guide...
Page 89
The text box displays how often (in seconds) this screen refreshes. You may change the refresh interval by typing a new number in the text box and then Set Interval clicking Set Interval. Stop Click Stop to halt statistic polling. IES-612-51A User’s Guide Chapter 7 System Information...
Page 90
Chapter 7 System Information IES-612-51A User’s Guide...
Enter the geographic location of your device. You can use up to 31 ASCII characters; spaces are allowed. Contact Person's Enter the name of the person in charge of this device. You can use up to 31 Name ASCII characters; spaces are allowed. IES-612-51A User’s Guide General Setup...
Page 92
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
H A P T E R The User Account screens allows you to set up and configure system administrator accounts for the IES-612-51A. You can also configure the authentication policy for IES-612-51A administrators. This is different than port authentication in Chapter 23 on page 181 9.1 User Account Screen...
Select low to allow the administrator to use only low privilege commands. Low privilege commands are read only. Click Add to save your changes to the IES-612-51A’s volatile memory. The IES- 612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non-volatile memory when you are done configuring.
DESCRIPTION User account Click this to open the User Account screen. See Authentication Mode Select the process by which the IES-612-51A authenticates administrators. local - Search the local database. You maintain this database in the User Account screen. radius - Check an external RADIUS database using the settings below.
Page 96
Chapter 9 User Account IES-612-51A User’s Guide...
(you should also enable RSTP). You can have multiple IES-612-51A connected on the same network and set both of them to use standalone mode in order to use them with a network topology that uses loops.
IES-612-51A that you set up in a daisychain. 10.2.4 Port Isolation with Daisychain Switch Mode Example In the example below, the IES-612-51A 1 has its Ethernet port one (ENET 1) connected to the Ethernet backbone switch (3) and it’s Ethernet port two (ENET2) connected to Ethernet port one (ENET 1) of the daisychained IES-612-51A (2).
(3 in the figure). A and B also cannot communicate with C without their communications going through another switch or router. Figure 42 Port Isolation with Daisychain Switch Mode Example 10.3 Switch Setup Screen To open this screen, click Basic Setting, Switch Setup. IES-612-51A User’s Guide Chapter 10 Switch Setup...
Each port has a single Leave All Period timer. Leave All Timer must be larger than Leave Timer. Turn on port isolation to block communications between subscriber ports. When you enable port isolation you do not need to configure the VLAN to isolate subscribers. IES-612-51A User’s Guide...
Page 101
LABEL DESCRIPTION MAC Anti-Spoofing Select this if you want the IES-612-51A to generate an alarm and issue a SNMP trap when an existing MAC address appears on another port. Switch Mode Select Standalone to use both of the IES-612-51A’s Ethernet ports (ENET 1 and ENET 2) as uplink ports.
Enter the IP address of your IES-612-51A in dotted decimal notation for example 1.2.3.4. IP Mask Enter the IP subnet mask of your IES-612-51A in dotted decimal notation for example 255.255.255.0. Apply IP setting Click Apply IP setting to save your changes to the device’s IP address and/or subnet mask to the IES-612-51A’s volatile memory.
Page 104
Chapter 11 IP Setup IES-612-51A User’s Guide...
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Page 106
Chapter 12 ENET Port Setup IES-612-51A User’s Guide...
13.1 ADSL Standards Overview These are the ADSL standards and rates that the IES-612-51A supports at the time of writing. The actual transfer rates will vary depending on what the subscriber’s device supports, the line conditions and the connection distance.
32 Kbps, and if you specify 66 Kbps, the actual rate will not be over 64Kbps. Regardless of a profile’s configured upstream and downstream rates, the IES-612-51A automatically limits the actual rates for each individual port to the maximum speeds supported by the port’s ADSL operational mode.
13.6 Default Settings The default profile always exists and all of the ADSL ports use the default profile settings when the IES-612-51A is shipped. The default profile's name is set to Chapter 56 on page 417 settings. 13.7 xDSL Port Setup Screen To open this screen, click Basic Setting, xDSL Port Setup.
13.9 on page 13.7.1 xDSL Port Setting Screen To open this screen, click Basic Setting, xDSL Port Setup, and then click a port’s index number. IES-612-51A User’s Guide Chapter 13 xDSL Port Setup 111). Section 13.7.1 on page Section 13.7.1 on page Section 13.7.1 on page...
(see Chapter 14 on page Select the port’s ADSL operational mode. Select the mode that the subscriber’s device uses or auto to have the IES-612-51A automatically determine the mode to use. See Table 18 on page 107 for information on the individual ADSL modes.
Page 113
DESCRIPTION Alarm Profile Select the port’s alarm profile. The alarm profile defines alarm thresholds for the ADSL port. The IES-612-51A sends an alarm trap and generates a syslog entry when the thresholds of the alarm profile are exceeded (see page IGMP Filter Profile The IGMP filter profile defines which multicast groups a port can join.
Page 114
Mask4 represents tones 128~159 Mask5 represents tones 160~191 Mask6 represents tones 192~223 Mask7 represents tones 224~255 For example, use 0x01000000 in Mask2 to disable downstream carrier tone 71. Use 0x03000000 in Mask2 to disable downstream carrier tones 70 and 71. IES-612-51A User’s Guide...
For example, you want to give high priority to voice service on one of the ADSL ports. Use the Edit Static VLAN screen to configure a static VLAN on the IES-612-51A for voice on the port.
You can also change an individual virtual channel by assigning it a different profile. The IES-612-51A provides two default virtual channel profiles: DEFVAL (for LLC encapsulation) and DEFVAL_VC (for VC encapsulation). By default, all virtual channels are associated to DEFVAL.
This field is read-only once you click on a port number below. Super Channel The IES-612-51A forwards frames belonging to VLAN groups that are not assigned to specific channels to the super channel. Enable the super channel option to have this channel forward frames belonging to multiple VLAN groups (that are not assigned to other channels).
Page 118
DESCRIPTION Use the drop-down list box to select a VC profile to use for this channel’s upstream traffic. The IES-612-51A does not perform upstream traffic policing if you do not specify an upstream VC profile. Note: Upstream traffic policing should be used in conjunction with the ATM shaping feature on the subscriber’s device.
Delete Figure 50 Basic Setting, xDSL Port Setup, VC Setup, Delete Figure 51 Select Ports IES-612-51A User’s Guide 1 Select a PVC’s Select radio button. 2 Click Delete. 3 Click OK if you want to remove the PVC from other ports. Click Cancel to only remove the one you selected.
A PPVC (Priority-based PVC) allows you to give different priorities to PVCs that are members of the same VLAN. The IES-612-51A uses eight priority queues (also called levels) for the member PVCs. The system maps frames with certain IEEE 802.1p priorities to a PVC with a particular priority queue.
Clicking Add / Modify saves your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Clicking Delete saves your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Clicking Delete saves your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Page 124
Chapter 13 xDSL Port Setup IES-612-51A User’s Guide...
(see Alarm Profile Click Alarm Profile to open the Alarm Profile screen where you can configure limits that trigger an alarm when exceeded (see IES-612-51A User’s Guide xDSL Profiles Setup Section 14.5 on page 131). Section 14.6 on page...
Page 126
Configure the upstream up shift signal to noise margin to be greater than or equal to the target upstream signal to noise margin and less than or equal to the maximum upstream signal to noise margin. Section 14.8 on page 135). IES-612-51A User’s Guide...
Click Add to save your changes to the IES-612-51A’s volatile memory. The IES- 612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non-volatile memory when you are done configuring.
However, while ABR gives subscribers a set amount of bandwidth, UBR doesn’t guarantee any bandwidth and only delivers traffic when the network has spare bandwidth. 14.3.2 Traffic Parameters These are the parameters that control the flow of ATM traffic. IES-612-51A User’s Guide...
CDVT controls the time scale over which the PCR is enforced. CDVT is used to determine if a cell arrived too early in relation to PCR. IES-612-51A User’s Guide Chapter 14 xDSL Profiles Setup...
PVC shaping parameters in order to get more upstream traffic bandwidth, it will violate the IES-612-51A's upstream policing profile and the traffic will be discarded. Operators can use this feature to prevent subscribers from changing their device settings.
The upstream policing feature can be enabled/disabled per PVC. No matter which ATM traffic class is used for the PVC's upstream traffic (CBR, VBR, or UBR), the IES-612-51A will drop any upstream traffic that violates the specified ATM VC profile.
Page 132
Type the BT here. BT applies with the VBR traffic classes. Click Add to save your changes to the IES-612-51A’s volatile memory. The IES- 612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non-volatile memory when you are done configuring.
14.6 Alarm Profile Screen Alarm profiles define ADSL port alarm thresholds. The IES-612-51A sends an alarm trap and generates a syslog entry when the thresholds of the alarm profile are exceeded. To open this screen, click Basic Setting, xDSL Profiles Setup, Alarm Profile.
These fields are for traffic coming from the subscriber’s device to the IES-612- 51A. These fields are for traffic going from the IES-612-51A to the subscriber’s device. This field sets the limit for the number of Loss Of Frame seconds that are permitted to occur within 15 minutes.
The top of the screen displays the configured IGMP filter profiles. Use the bottom part of the screen (with the Add and Cancel buttons) to add or edit alarm profiles. Figure 60 IGMP Filter Profile IES-612-51A User’s Guide Chapter 14 xDSL Profiles Setup Section 13.7.1 on page...
If you want to add a single multicast IP address, enter it in both the Start IP and End IP fields. Click Add to save your changes to the IES-612-51A’s volatile memory. The IES- 612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non-volatile memory when you are done configuring.
Use this drop-down list box to select a port for which you wish to view information. Refresh Click Refresh to display updated information. Port Name This section displays the name of the port. IES-612-51A User’s Guide xDSL Line Data Section 15.2 on page 138). 140). Section 15.3 on...
Output Power Info Atur Info Atuc At the time of writing, the IES-612-51A always uses Trellis coding. 15.2 xDSL Performance Screen These counters display line performance data that has been accumulated since the system started. The definitions of near end/far end are always relative to the ATU-C (ADSL Termination Unit-Central Office).
Use this drop-down list box to select a port for which you wish to view information. Refresh Click Refresh to display updated information. Port Name This section displays the name of the port. Performance (since last link up) IES-612-51A User’s Guide 137). 140). Chapter 15 xDSL Line Data Section Section 15.3 on...
The number of Errored Seconds that have occurred within the period. The number of successful initializations that have occurred within the period. The number of Severely Errored Seconds that have occurred within the period. The number of UnAvailable Seconds that have occurred within the period. IES-612-51A User’s Guide...
In the screen shown, the downstream channel is carried on tones 48 to 255 and the upstream channel is carried on tones 16 to 31 (space is left between the channels to avoid interference). Figure 63 xDSL Line Data IES-612-51A User’s Guide...
This section displays the name of the port. “DS carrier load” displays the number of bits transmitted per DMT tone for the downstream channel (from the IES-612-51A to the subscriber’s DSL modem or router). “US carrier load” displays the number of bits received per DMT tone for the upstream channel (from the subscriber’s DSL modem or router to the IES-612-...
ID are independent of each other. A frame with VID (VLAN Identifier) of null (0) is called a GVRP (GARP VLAN Registration Protocol) defines a way for switches to automatically configure switches in a VLAN network. IES-612-51A User’s Guide VLAN ) VLANs. Note that user priority and VLAN...
User Priority 2 Bytes 3 Bits The IES-612-51A handles up to 4094 VLANs (VIDs 1-4094). The device accepts incoming frames with VIDs 1-4094. 16.2.1 Forwarding Tagged and Untagged Frames Each port on the device is capable of passing tagged or untagged frames. To forward a frame from an 802.1Q VLAN-aware switch to an 802.1Q VLAN-unaware switch, the IES-612-51A...
This field shows how long it has been since a normal VLAN was registered or a static VLAN was set up. Status This field shows that this VLAN was added to the IES-612-51A statically, that is, added as a permanent entry. IES-612-51A User’s Guide Section 16.4 on page...
Click one of these buttons to show the preceding/following screen if the information cannot be displayed in one screen. DESCRIPTION Click VLAN Status to see which of the IES-612-51A’s ports are members of which VLANs (see Section 16.3 on page Click VLAN Port Setting to specify Port VLAN IDs (PVIDs).
Clicking Add saves your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Figure 67 Select Ports At the time of writing, the VLAN Acceptable Frame Type field is read-only for the Ethernet ports. The IES-612-51A accepts both tagged and untagged incoming frames on the Ethernet ports. IES-612-51A User’s Guide port. Use None to clear all of the check boxes.
IES-612-51A to learn multicast groups without you having to manually configure them. The IES-612-51A forwards multicast traffic destined for multicast groups (that it has learned from IGMP snooping or that you have manually configured) to ports that are members of that group.
There should only be one upstream interface (also known as the query port) for one query VLAN on the IES-612-51A. A downstream interface is a port that connects to a host (such as a computer).
This is the total number of Report packets received. Leave This is the total number of Leave packets received. Number of IGMP This is how many IGMP groups the IES-612-51A has identified on the local Groups network. Previous Click one of these buttons to show the previous/next screen if all of the information cannot be seen in one screen.
Click Port Setup to open the Bandwidth Port Setup screen where you can set up multicast bandwidth requirements on specified ports (see page 157). Enter the default bandwidth for multicast channels for which you have not configured bandwidth requirements. Section 17.4.1 on IES-612-51A User’s Guide...
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Clicking Apply saves your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Click this to disable the specified IGMP count limits on the selected ports. Select All Click this to select all entries in the table. Select None Click this to un-select all entries in the table. IES-612-51A User’s Guide 135. Section 17.3 on page 154). Chapter 17 IGMP...
This is the total number of Join packets received on this port. This is the total number of Leave packets received on this port. Click Clear to delete the information the IES-612-51A has learned about multicast groups. This resets every counter in this screen.
This field shows the IP address of the multicast group joined by this port. Source IP This field shows the IP address of the client that joined the multicast group on this port. Refresh Click Refresh to display updated information. IES-612-51A User’s Guide Chapter 17 IGMP Section 17.3 on page 154).
Table 42 Static Multicast LABEL DESCRIPTION The Number of This is the number of static multicast entries configured on the IES-612-51A. Static Multicast Page X of X This identifies which page of information is displayed and the total number of pages of information.
Page 164
Clicking Add saves your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Ethernet port should join the multicast VLAN. 19.2 MVLAN Status Screen Use this screen to look at a summary of all multicast VLAN on the IES-612-51A. To open this screen, click Advanced Application, Multicast VLAN.
IP addresses for each multicast VLAN (see Section 19.4 on page 168). This is the number of multicast VLAN configured on the IES-612-51A. The first table displays the names of the fields. The subsequent tables show the settings for each multicast VLAN.
DESCRIPTION MVLAN Status Click MVLAN Status to open the MVLAN Status screen where you can view a summary of all multicast VLAN on the IES-612-51A (see 165). MVLAN Group Click MVLAN Group to open the MVLAN Group screen where you can configure ranges of multicast IP addresses for each multicast VLAN (see Section 19.4 on page...
VLAN ID. Use the All button to include every port. Use the None button to clear all of the ports check boxes. Click Add to save your changes to the IES-612-51A’s volatile memory. The IES- 612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non-volatile memory when you are done configuring.
Page 169
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
H A P T E R This chapter describes how to configure the Packet Filter screen. 20.1 Packet Filter Screen Use this screen to set which types of packets the IES-612-51A accepts on individual DSL ports. To open this screen, click Advanced Application, Filtering.
Page 172
These are the packet filter settings for each port. “V” displays for the packet types that the IES-612-51A is to accept on the port. “- “ displays for packet types that the IES-612-51A is to reject on the port (packet types that are not listed are accepted).
Type a device’s MAC address in hexadecimal notation (xx:xx:xx:xx:xx:xx, where x is a number from 0 to 9 or a letter from a to f) in this field. The MAC address must be a valid MAC address. IES-612-51A User’s Guide MAC Filter...
Page 174
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
(RSTP). 22.1 RSTP and STP RSTP adds rapid reconfiguration capability to STP. The IES-612-51A supports RSTP and the earlier STP. RSTP and STP detect and break network loops and provide backup links between switches, bridges or routers. They allow a device to interact with other RSTP or STP-aware devices in your network to ensure that only one path exists between any two stations on the network.
In STP, all BPDUs are received and processed. Learning All BPDUs are received and processed. Information frames are submitted to the learning process but not forwarded. Forwarding All BPDUs are received and processed. All information frames are received and forwarded. Table IES-612-51A User’s Guide...
Designated root ID This is the unique identifier for the root bridge, consisting of bridge priority plus MAC address. This ID is the same in Our bridge ID if the IES-612-51A is the root switch. Topology change This is the number of times the spanning tree has been reconfigured.
This is the time (in seconds) the IES-612-51A will wait before changing states (that is, listening to learning to forwarding). This identifies the IES-612-51A’s ports that support the use of STP. If STP is activated, the following fields appear. If STP is not activated, Disabled appears.
Table 51 Spanning Tree Protocol LABEL DESCRIPTION STP Status Click STP Status to display the IES-612-51A’s STP status (see page Active Select this check box to turn on RSTP. Note: It is recommended that you only use STP when you use the...
Page 180
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Figure 85 RADIUS Server 23.1.2 Introduction to Local User Database By storing user profiles locally on the IES-612-51A, your IES-612-51A is able to authenticate users without interacting At the time of writing, Windows XP of the Microsoft operating systems supports 802.1x. See the Microsoft web site for information on other Windows operating system support.
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Page 184
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Clear this check box to not limit the number of MAC addresses that can be learned on the port. Limited Number of Specify how many MAC addresses the IES-612-51A can learn on this port. The Learned MAC range is 1~128.
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
DHCP servers for each VLAN. 25.2 DHCP Relay Agent Information Option (Option 82) The IES-612-51A can add information to DHCP requests that it relays to a DHCP server. This helps provide authentication about the source of the requests. You can also specify additional information for the IES-612-51A to add to the DHCP requests that it relays to the DHCP server.
Chapter 25 DHCP Relay The Agent Information field that the IES-612-51A adds also contains an “Agent Remote-ID sub-option” of information that you specify. The following figure shows the format of the Agent Remote ID sub-option. The 2 in the first field identifies this as an Agent Remote ID sub-option.
Use this field to specify up to 23 ASCII characters of additional information for the IES-612-51A to add to the DHCP requests that it relays to a DHCP server. Examples of information you could add would be the chassis number of the IES- 612-51A or the ISP’s name.
Page 190
Select the check box in the Select column for an entry, and click Delete to remove the entry. Click this to select all entries in the Server List. Click this to un-select all entries in the Server List. IES-612-51A User’s Guide...
This chapter shows you how to set up DHCP snooping settings on the subscriber ports. 26.1 DHCP Snoop Overview DHCP snooping prevents clients from assigning their own IP addresses. The IES-612-51A can store every (DSL port, MAC address, IP address) tuple offered by the DHCP server. Then, it only forwards packets from clients whose MAC address and IP address are recorded.
This field displays the MAC address of a client on this port to which the DHCP server assigned an IP address. Click Flush to remove all of the entries from the DHCP snooping table for the selected port(s). 191). 193). IES-612-51A User’s Guide...
The DHCP server can assign up to 32 IP addresses at one time to each port. This field displays the number of requests from DHCP clients above this limit. Clear Click Clear to delete the information the IES-612-51A has learned about DHCP packets. This resets every counter in this screen. IES-612-51A User’s Guide Chapter 26 DHCP Snoop Section 26.2 on page...
2684 routed mode traffic from a PVC that connects to a subscriber device that uses 2684 routed mode. You also specify the gateway to which the IES-612-51A sends the traffic and the VLAN ID tag to add. See RFC-2684 for details on routed mode traffic carried over AAL type 5 over ATM.
WAN IP address or routed gateway IP address. • The IES-612-51A’s management IP address should not be in the same subnet as the one defined by the WAN IP address and netmask of the subscriber’s device. It is suggested that you set the netmask of the subscriber’s WAN IP address to 32 to avoid this problem.
Click Add to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Clicking Delete saves your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Click Add to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Click Apply Setting to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Click Add to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
H A P T E R This chapter shows you how to set up the IES-612-51A to convert PPPoA frames to PPPoE traffic and vice versa. 28.1 PPPoA to PPPoE Overview Before migrating to an Ethernet infrastructure, a broadband network might consist of PPPoA connections between the CPE devices and the DSLAM and PPPoE connections from the DSLAM to the Broadband Remote Access Server (BRAS).
Use the drop-down list box to select a VC profile to use for this channel’s upstream traffic. The IES-612-51A does not perform upstream traffic policing if you do not specify an upstream VC profile. Note: Upstream traffic policing should be used in conjunction with the ATM shaping feature on the subscriber’s device.
Page 205
PAE translation to the specified access concentrator. In this case, the IES- 612-51A checks the AC name field in the BRAS's reply PDU. If there is a mismatch, the IES-612-51A drops this PDU. (This is not recorded as an PPPoE AC System Error in the PPPoA to PPPoE Status screen, however.) Service Name This field is optional.
This field displays the hostname of the remote access concentrator if there are two access concentrators (or BRAS) on the network or if you want to allow PAE translation to the specified access concentrator. Section 28.2 on page 203). IES-612-51A User’s Guide...
Page 207
Reply from the CPE (client) device. PPPoE PADI This field displays the number of padi PDUs sent by the IES-612-51A to the BRAS. PPPoE PADO This field displays the number of pado PDUs sent by the BRAS to the IES-612- 51A.
Page 208
Chapter 28 PPPoA to PPPoE IES-612-51A User’s Guide...
DSCP priority and IEEE 802.1p priority (see page Port This field displays each port number. Active This field displays whether DSCP is active (“V”) or inactive (“-”) on this port. IES-612-51A User’s Guide 210). DSCP Section 29.3 on...
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
VLAN tag overlap among customers, so traffic from different customers is kept separate. Before the IES-612-51A sends the frames from the customers, the VLAN ID is added to the frames. When packets intended for specific customers are received on the IES-612-51A, the outer VLAN tag is removed before the traffic is sent.
Use this screen to set up Transparent LAN Services on each port. This is set up by creating a TLS PVC. See Chapter 13 on page 107 open this screen, click Advanced Application, TLS PVC. You can NOT configure PPPoA-to-PPPoE and TLS settings on the same PVC. for background information about creating PVCs. To IES-612-51A User’s Guide...
US VC Profile Use the drop-down list box to select a VC profile to use for this channel’s upstream traffic. The IES-612-51A does not perform upstream traffic policing if you do not specify an upstream VC profile. Note: Upstream traffic policing should be used in conjunction with Type a VLAN ID to assign to frames received on this channel.
Page 214
Select the check box in the Select column for an entry, and click Delete to remove the entry. Click this to select all entries in the table. Click this to un-select all entries in the table. IES-612-51A User’s Guide...
This chapter shows you how to set up ACL profiles on each port. 31.1 Access Control Logic (ACL) Overview An ACL (Access Control Logic) profile allows the IES-612-51A to classify and perform actions on the upstream traffic. Each ACL profile consists of a rule and an action, and you assign ACL profiles to PVCs.
VLAN ID on super channels, not normal PVC, since super channels accept any tagged traffic. If you replace the VLAN ID for a normal PVC, the IES-612-51A drops the traffic because the new VLAN ID does not match the VID of the PVC. This is illustrated in the following scenario.
PVC. Apply Click this to save your changes to the IES-612-51A’s volatile memory. The IES- 612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non-volatile memory when you are done configuring.
Click ACL Setup to open the screen where you can assign ACL profiles to PVCs (see Section 31.2 on page 216). Click ACL Profile Map to open the screen where you can look at which ACL profiles are assigned to which PVCs (see Section 31.4 on page 219). IES-612-51A User’s Guide...
Select the IEEE 802.1p priority that this traffic should have. deny Select this if you want the IES-612-51A to reject this kind of traffic. ACL Profile List Index This field displays a sequential value. The sequence in this table is not important.
This field shows the ACL profile assigned to this PVC. This field displays the DSL port number on which the PVC is configured. This field displays the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI). The VPI and VCI identify a channel on this port. IES-612-51A User’s Guide...
Click Add to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Page 222
Clicking Delete saves your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Simple Network Management Protocol is a protocol used for exchanging management information between network devices. SNMP is a member of TCP/IP protocol suite. A manager station can manage and monitor the IES-612-51A through the network via SNMP version one (SNMPv1) and/or SNMP version 2c. The next figure illustrates an SNMP management operation.
Get operation, followed by a series of GetNext operations. Allows the manager to set values for object variables within an agent. Used by the agent to inform the manager of some events. IES-612-51A User’s Guide...
MIBs the IES-612-51A supports. 34.3.2 SNMP Traps The IES-612-51A can send the following SNMP traps to an SNMP manager when an event occurs. ATUC refers to the downstream channel (for traffic going from the IES-612-51A to the subscriber).
15-minute interval. The number of Unavailable seconds within 15 minutes for the ATUR has reached the threshold. currValue is the number of Unavailable seconds that have occurred within the 15-minute interval. IES-612-51A User’s Guide...
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Page 232
Chapter 34 Access Control IES-612-51A User’s Guide...
H A P T E R This chapter shows you how to configure the static routing function. Static routes tell the IES-612-51A how to forward the IES-612-51A’s own IP traffic when you configure the TCP/IP parameters manually. This is generally useful for allowing management of the device from a device with an IP address on a different subnet from that of the device’s...
Page 236
Click Cancel to reset the fields to your previous configuration. Use this section to look at a summary of all static routes in the IES-612-51A. Click this to display the preceding page of static route entries.
Be sure to upload the correct model firmware as uploading the wrong model firmware may damage your device. To open this screen, click Management, Maintenance, Click here (Firmware Upgrade). IES-612-51A User’s Guide Maintenance...
36.4 Backing Up a Configuration File Backing up your device configurations allows you to create various “snap shots” of your device from which you may restore at a later date. IES-612-51A User’s Guide...
This takes up to two minutes. If you want to access the web configurator again, you may need to change the IP address of your computer to be in the same subnet as that of the default device IP address (192.168.1.1). IES-612-51A User’s Guide Chapter 36 Maintenance...
This takes up to two minutes. This does not affect the device’s configuration. 36.7 Command Line FTP Chapter 50 on page 335 FTP commands. Figure 123 on page for how to upload or download files to or from the device using 240. Click OK again and IES-612-51A User’s Guide...
H A P T E R This chapter explains the Diagnostic screens. 37.1 Diagnostic Screen Use this screen to check system logs, ping IP addresses or perform loopback tests. To open this screen, click Management, Diagnostic. Figure 125 Diagnostic IES-612-51A User’s Guide Diagnostic...
Select a port number from the Port drop-down list box and click Set LDM Port to have the IES-612-51A perform line diagnostics on the specified port. The ADSL port must be set to ADSL2 or ADSL2+ ADSL operational mode and have a connection.
Page 243
ITU-T G.992.3 standard. Use the information to analyze problems with the physical ADSL line. Note: ToneDiag is faster than the LDM test but displays less IES-612-51A User’s Guide information. Chapter 37 Diagnostic...
This chapter introduces the MAC Table. 38.1 Introduction to MAC Table The MAC table lists device MAC addresses that are dynamically learned by the IES-612-51A. The table shows the following for each MAC address: the port upon which Ethernet frames were received from the device, to which VLAN groups the device belongs (if any) and to which channel it is connected (for devices connected to DSL ports).
This is the MAC address of the device from which this incoming frame came. Click Refresh to update the list of dynamically learned MAC addresses. Click Flush to remove all of the dynamically learned MAC address entries from the MAC table. IES-612-51A User’s Guide...
ARP Table for future reference and then sends the packet to the MAC address that replied. 39.2 ARP Table Screen The ARP table can hold up to 500 entries. To open this screen, click Management, ARP Table. IES-612-51A User’s Guide ARP Table...
This is the learned IP address of a device connected to a port. This is the MAC address of the device with the listed IP address. Click one of these buttons to show the preceding or following screen if the information cannot be displayed in one screen. IES-612-51A User’s Guide...
40.1 Alarm The IES-612-51A monitors for equipment, DSL and system alarms and can report them via SNMP or syslog. You can specify the severity level of an alarm(s) and where the system is to send the alarm(s).
40.3 Alarm Descriptions This table describes alarms that the system can send. ATUC refers to the downstream channel (for traffic going from the IES-612-51A to the subscriber). ATUR refers to the upstream channel (for traffic coming from the subscriber to the IES-612-51A).
This screen lists the alarms that the system can generate along with the severity levels of the alarms and where the system is to send them. To open this screen, click Alarm, Alarm Event Setup. IES-612-51A User’s Guide FACILITY SNMP...
This field displays a text description for the condition under which the alarm applies. This field displays the log facility (local1~local7) on the syslog server where the system is to log this alarm. This is for alarms that send alarms to a syslog server. 249). Section IES-612-51A User’s Guide...
Select this check box to keep an alarm report generated by this alarm event in the system until the conditions that caused the alarm report are no longer present. IES-612-51A User’s Guide Chapter 40 Alarm...
Click Apply to save your changes to the IES-612-51A’s volatile memory. The IES-612-51A loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to save your changes to the non- volatile memory when you are done configuring.
Administrators with high privilege access can use all commands including the lower privilege commands. IES-612-51A User’s Guide courier new font ” command could be abbreviated to “...
Save your changes after each configuration session. Nonvolatile memory refers to the IES-612-51A’s storage that remains even if the IES-612- 51A’s power is turned off. Run-time (memory) is lost when the IES-612-51A’s power is turned off. 41.4 Commands The following table lists commands that you can use with the IES-612-51A.
Page 260
Turns on the specified user name <name> of multi-login. Turns off the specified user name <name> of multi-login. Creates or edits the password and <username> privilege level of the specified <password> user name. <high|middle|low> Removes the specified user name <name> of multi-login. IES-612-51A User’s Guide...
Page 261
IES-612-51A User’s Guide Chapter 41 Commands Summary PARAMETERS DESCRIPTION Displays the authentication mode, RADIUS server settings and user info. Set authentication method. <local|radius|land r> Set remote authentication server <ip>...
Page 262
<portlist> <vpi> <vci> Set gateway for RPVC <gateway ip> <vlan id> [<priority>] Delete gateway for RPVC <gateway ip> Display gateway for RPVC Set RPVC on a port <portlist> <vpi> <vci> <DS vcprofile[,US vcprofile]> <ip>/ <netmask> <gateway ip> IES-612-51A User’s Guide...
Page 263
IES-612-51A User’s Guide Chapter 41 Commands Summary PARAMETERS DESCRIPTION Delete RPVC on a port <portlist> <vpi> <vci> Display RPVC on a port <portlist>...
Page 264
Displays alarm profile to ADSL [port number] port mapping. Displays which alarm profile <port number> parameters are mapped to an ADSL port. Display or set Maximum nominal <port number> transmit PSD in the US direction [<max nominal psd>] IES-612-51A User’s Guide...
Page 265
IES-612-51A User’s Guide Chapter 41 Commands Summary PARAMETERS DESCRIPTION Display or set Maximum nominal <port number> transmit PSD in the DS direction [<max nominal psd>]...
Page 266
[for|rev] [detail] Display current alarm [<severity>|all] [<alarm>|all] [<condition>|all] [<sdate>|all] [<edate>|all] [for|rev] [detail] Display xDSL port threshold of [<severity>|all] severity which will issue an alarm Set xDSL port threshold of <all|enet1|enet2|p severity which will issue an alarm ort> <severity> IES-612-51A User’s Guide...
Page 268
Display the system’s garp settings. Set system’s garp join time. <join msec> Set system’s garp leave time. <leave msec> Set system’s garp leaveall time. <leaveall msec> Display the system’s rstp settings. M/L Turn system’s rstp on. IES-612-51A User’s Guide...
Page 269
IES-612-51A User’s Guide Chapter 41 Commands Summary PARAMETERS DESCRIPTION Turn system’s rstp off. Set system rstp’s priority. <priority> Set system rstp’s hello time. <hellotime sec> Set system rstp’s max age.
Page 270
<rvlan>: replaced vlan 1~4094 <rpri>: replaced priority 0~7 Display an acl profile [<name>] Display acl profile reference <name> Remove an acl profile from PVC <portlist> <vpi> <vci> <profile> <profile>: string32 up to 8 profiles if only one PVC has profiles IES-612-51A User’s Guide...
Page 271
IES-612-51A User’s Guide Chapter 41 Commands Summary PARAMETERS DESCRIPTION Apply an acl profile to a PVC <portlist> <vpi> <vci> <profile> Max. 8 profiles per port Show acl profile setting for a PVC [portlist] [<vpi>...
Page 272
ADSL port(s). [<mac> <mac> ...] Display packet filter settings. [portlist] Set packet filter for port set <portlist> <filter> Set packet filter to pppoe only for pppoeonly port. <portlist> Display dot1x settings. [portlist] Turn on dot1x. IES-612-51A User’s Guide...
Page 273
IES-612-51A User’s Guide Chapter 41 Commands Summary PARAMETERS DESCRIPTION Turn off dot1x. Set authentication method to <profile|radius> profile or radius. Turn on dot1x on port.
Page 274
Clears the routing table. Pings a remote host. <ip> [count] Displays hardware monitor status. M/L Displays ADSL port connection [portlist] status. Displays the line data load per <portlist> symbol (tone). Displays the info of the specified <portlist> ADSL ports. IES-612-51A User’s Guide...
Page 275
IES-612-51A User’s Guide Chapter 41 Commands Summary PARAMETERS DESCRIPTION Displays the performance <portlist> statistics of the specified ADSL port. Displays the line rate. <portlist> Displays line performance <portlist> [count statistics for the current and <0..96>]...
<item no> This is the time and date when the log was created. <time> This is the process that created the log. <process> IES-612-51A User’s Guide Command Examples for commands that deal with the IEEE 802.1Q Tagged INFO Session Begin!
A console, telnet or FTP session has begun (see the <process> field for the type of session). A console telnet or FTP session has terminated (see the <process> field for the type of session). Table 90 on page 278) IES-612-51A User’s Guide...
Page 279
IP address. The device synchronized the time with the time server at the listed IP address. A file was uploaded to the IES-612-51A by FTP. <file> - received file’s name A checksum error was detected during an attempted FTP firmware upload.
VLAN to isolate subscribers. 42.4.1 Isolation Show Command Syntax: ras> switch isolation show This command displays the current setting of the subscriber isolation feature. 0(days) : 22:31:49 7 2006 10:00:31 6.04.0003 IES-612-51A User’s Guide...
You can specify a single port <1>, all ports <*> or a list of ports <1,3,enet1>. You can also include a range of ports <1,5,6~10,enet1,enet2>. The VPI and VCI of an individual PVC. to have the IES-612-51A set the specified clear port(s) or PVC’s counters back to zero. : 20...
43.3 Alarm Show Command Syntax: ras> alarm show [<severity>|all] [<alarm>|all] [<condition>|all] [detail] where [detail] This command displays the current alarms by severity, alarm category or alarm condition. IES-612-51A User’s Guide Alarm Commands Display in-depth alarm information.
The system reports an alarm on a port if the alarm has a severity equal to or higher than the port’s threshold. The following example has the IES-612-51A only record critical alarms on DSL port 7. Figure 140 Alarm Port Set Command Example ras>...
This displays “V” if the alarm clear command removes the alarm from the system. It displays “-“if the alarm clear command does not remove the alarm from the system. info minor minor minor minor minor minor minor minor minor minor minor minor minor critical critical critical critical info IES-612-51A User’s Guide...
The following example removes the historic minor level alarms for all alarm categories, and all conditions. Figure 143 Alarm History Clear Command Example ras> alarm history clear minor IES-612-51A User’s Guide The start date, in yyyy/mm/dd The end date, in yyyy/mm/dd The displaying order.
This sets whether or not the clearable|unclearable alarm clear command removes the alarm from the system. command to display alarm setting details. alarm to find alarm ) has the device log the IES-612-51A User’s Guide...
This command displays whether or not the DHCP relay feature is activated, which relay mode the IES-612-51A is using, the current list of DHCP servers by VLAN, the status of the DHCP relay agent info option 82 feature and the information configured for it.
This command specifies the DHCP server(s) that serve the specified VLAN. The primary server is required; the secondary server is optional. The IES-612-51A routes DHCP requests to the specified DHCP server(s) according to the Use VLAN ID 0 to set up the default DHCP server(s) for all non-listed VLAN.
<active-server> = This command has no effect if the relaymode is both. If the relaymode is auto, this command specifies to which DHCP server (the primary one or the secondary one) the IES-612-51A should relay DHCP requests for the selected VLAN.
[<relay info>] Up to 23 ASCII characters of additional information for the IES-612-51A to add to the DHCP requests that it relays to a DHCP server. Examples of information you could add would be the name of the IES-612-51A or the ISP.
IES-612-51A User’s Guide Chapter 44 DHCP Commands Up to 23 ASCII characters of additional information for the IES-612-51A to add to the DHCP requests that it relays to a DHCP server. Examples of information you could add would be the name of the IES-612-51A or the ISP.
You can specify a single port <1>, all ports <*> or a list of ports <1,3,enet1>. You can also include a range of ports <1,5,6~10,enet1,enet2>. You can specify a single port <1>, all ports <*> or a list of ports <1,3,enet1>. You can also include a range of ports <1,5,6~10,enet1,enet2>. IES-612-51A User’s Guide...
Figure 149 DHCP Snoop Statistics Command Example ras> statistics dhcp snoop 1 port overflow ---- -------- ----------------- --------------- IES-612-51A User’s Guide You can specify a single port <1>, all ports <*> or a list of ports <1,3,enet1>. You can also include a range of ports <1,5,6~10,enet1,enet2>.
Page 298
This field displays the number of requests from DHCP clients above this limit. The MAC address of a client on this port to which the DHCP server assigned an IP address. The IP address assigned to a client on this port. IES-612-51A User’s Guide...
The IEEE 802.1Q Tagged VLAN uses both explicit and implicit tagging. It is important for the IES-612-51A to determine what devices are VLAN-aware and VLAN- unaware so that it can decide whether to forward a tagged frame (to a VLAN-aware device) or first strip the tag from a frame and then forward it (to a VLAN-unaware device).
<1,3,enet1>. You can also include a range of ports <1,5,6~10,enet1,enet2>. You can specify a single port <1>, all ports <*> or a list of ports <1,3,enet1>. You can also include a range of ports <1,5,6~10,enet1,enet2>. The VLAN ID. Valid parameter range = [1 – 4094]. IES-612-51A User’s Guide...
This command adds or modifies an entry in the static VLAN table. Use the command to display your configuration. An example of a configuration is shown next. show IES-612-51A User’s Guide Chapter 45 IEEE 802.1Q Tagged VLAN Commands You can specify a single port: <1>, all ports: <*>, a list of ports: <1,3,enet1>, you can also include a range of ports:...
51A does not send a frame to the port from which it came. The IES-612-51A also does not forward frames to “forbidden” ports. 5 If after looking at the SVLAN, the IES-612-51A does not have any ports to which it will send the frame, it drops the frame.
The IES-612-51A accepts both tagged and untagged incoming frames on the Ethernet ports. The following example sets the IES-612-51A to accept only VLAN tagged Ethernet frames on DSL port 3. Figure 154 VLAN Frame Type Command Example ras> switch vlan frametype 3 tag 45.4.6 VLAN CPU Show Command...
Ethernet port through a VLAN aware device that is using the proper VLAN ID in order to perform management. By default, the IES-612-51A’s DSL ports are members of the management VLAN (VID 1). The following procedure shows you how to configure a tagged VLAN that limits management access to just one Ethernet port.
T:tag ---- ------------------------------- -------------------------------------- 1 DEFAULT enabled IES-612-51A User’s Guide Chapter 45 IEEE 802.1Q Tagged VLAN Commands You can specify a single VID: <1>, all VIDs: <*>, a list of VIDs: <1,3>, you can also include a range of VIDs: <1,5,6~10>.
H A P T E R This chapter describes how to configure the IES-612-51A’s MAC commands. 46.1 MAC Commands Overview Use the MAC commands to configure MAC filtering or limit the MAC count. 46.2 MAC Filter Commands Use the MAC filter to control from which MAC (Media Access Control) addresses frames can (or cannot) come in through a port.
<1,5,6~10>. accept = Only allow frames from MAC addresses that you specify and block frames from other MAC addresses. deny = Block frames from MAC addresses that you specify and allow frames from other MAC addresses. IES-612-51A User’s Guide...
This command sets whether the IES-612-51A allows or blocks access for the MAC addresses you specify. The following example sets DSL port 5 to allow frames from the MAC addresses specified for DSL port 5. Figure 164 MAC Filter Mode Command Example ras>...
Figure 168 MAC Count Enable Command Example ras> switch mac count enable 4 307), the IES-612-51A ignores the MAC count setting and accepts all of You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>.
Figure 170 MAC Count Set Command Example ras> switch mac count set 7 50 IES-612-51A User’s Guide You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>.
Page 312
Chapter 46 MAC Commands IES-612-51A User’s Guide...
Use IGMP snooping to have the device passively learn multicast groups. The following example sets the device to use IGMP proxy. Figure 172 IGMP Snoop Enable Command Example ras> switch igmpsnoop enable proxy IES-612-51A User’s Guide IGMP Commands for background information on this feature.
Syntax: ras> switch igmpfilter set [<port>|*] <name> You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. profile DEFVAL IES-612-51A User’s Guide...
Syntax: ras> switch igmpfilter profile delete <name> where <name> IES-612-51A User’s Guide You can specify a single DSL port <1> or all DSL ports <*>. The name of an IGMP filter profile. Specify a name to identify the IGMP filter profile (you cannot change the name of the DEFVAL profile).
47.5 IGMP Bandwidth Port Commands Use the IGMP bandwidth port commands to set up bandwidth budgets for multicast traffic on specific ports. IES-612-51A User’s Guide Allowed bandwidth between 1 and 1000 000 kbps (kilo bits per second). command) have higher priority over this default 1..96;...
DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. 1..100000, in units of kbps IES-612-51A User’s Guide...
Figure 180 IGMP Count Disable Command Example ras> switch igmpsnoop igmpcount disable 4 IES-612-51A User’s Guide You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>.
You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. 0..16; the maximum number of IGMP groups subscribers on the specified port(s) can join. IES-612-51A User’s Guide...
47.7.2 IGMP Group Statistics Command Syntax: ras> statistics igmpsnoop group [<vid> [<mcast_ip>]] IES-612-51A User’s Guide You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>.
DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. join_cnt leave_cnt You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. IES-612-51A User’s Guide...
This command is similar to the command to create a regular VLAN. See page 301 for examples and more information. IES-612-51A User’s Guide source ip The VLAN ID [1 – 4094]. You can specify a single port: <1>, all ports: <*>, a list of ports: <1,3,enet1>, you can also include a range of ports:...
You can specify a single VLAN: <1>, all VLAN: <*>, a list of VLAN: <1,3>, you can also include a range of VLAN: <1,5,6~10>. The multicast VLAN ID [1 – 4094]. The multicast VLAN ID [1 – 4094]. IES-612-51A User’s Guide...
<vid> <index> where <vid> <index> IES-612-51A User’s Guide You can specify a single VLAN: <1>, all VLAN: <*>, a list of VLAN: <1,3>, you can also include a range of VLAN: <1,5,6~10>. F:fixed X:forbidden U:untag T:tag The multicast VLAN ID [1 –...
This command removes the specified multicast VLAN group setting. 47.8.8 Multicast VLAN Group Show Command Syntax: ras> switch igmpsnoop mvlan group show [<vid>] where <vid> This command displays a multicast to VLAN translation entry. The multicast VLAN ID [1 – 4094]. IES-612-51A User’s Guide...
IES-612-51A is to accept on the port. “-“ displays for packet types that the IES-612-51A is to reject on the port (packet types that are not listed are accepted). When you use PPPoE only,”#” appears for all of the packet types. With PPPoE only, the IES-612-51A rejects all packet types except for PPPoE (packet types that are not listed are also rejected).
(besides RADIUS) to be deployed with no changes to the access point or the wireless clients. [igmp] Reject IGMP packets. Internet Group Multicast Protocol is used when sending packets to a specific group of hosts. [none] Accept all packets. IES-612-51A User’s Guide...
Syntax: ras> switch pktfilter pppoeonly <portlist> This command sets the IES-612-51A to allow only PPPoE traffic on the specified DSL port(s). The system will drop any non-PPPoE packets. The following example sets DSL port 1 to accept only PPPoE packets.
2, and DSL ports, VID and default gateway. With the Ethernet 1 and 2, and DSL ports, you must connect to the IES-612-51A through a port that is a member of the management (CPU) VLAN in order to perform in-band management.
192.168.1.233 ras> config save The IES-612-51A leaves the factory with a default management IP address of 192.168.1.1 and a subnet mask of 255.255.255.0, (ff:ff:ff:00 in hexadecimal notation), and the default gateway set at 192.168.1.254. Make sure that you configure the IP parameters correctly before you connect a IES-612-51A to the network, otherwise, you may interrupt services already running.
The metric (hop count) of this static route. A name to identify this static route. Up to 31 ASCII characters. Spaces and tabs are not allowed. Use this to configure the IES-612-51A’s default route. The destination IP address of packets to which this static route applies.
49.3.6 ARP Show Command Syntax: ras> ip arp show This command displays the IES-612-51A’s IP Address Resolution Protocol table. This is the list of IP addresses and matching MAC addresses that the IES-612-51A has resolved. An example is shown next.
51A. 50.1 Firmware and Configuration File Maintenance Overview The IES-612-51A’s built-in FTP server allows you to use any FTP client (for example, ftp.exe in Windows) to upgrade IES-612-51A firmware or configuration files. The firmware or configuration file upgrade is done during operation (run-time).
Figure 200 FTP Get Configuration File Example ftp> get config-0 config.txt This is a sample from a FTP session to transfer the IES-612-51A’s current configuration file (including the configuration files of all the IES-612-51A) to the computer file If your FTP client does not allow you to have a destination filename different than the source, you will need to rename them as the IES-612-51A only recognizes “config-0”...
Use an FTP client to connect to the IES-612-51A. Figure 201 Example: Use an FTP Client to Connect to the IES-612-51A C:\> ftp <IES-612-51A IP address> Type your user name and press [ENTER]. User (172.23.15.86:(none)): admin Enter the management password (...
------------- sys user set admin editor. Attempting to edit it and upload it to the IES-612-51A will lock you out after the system restarts. If this happens you will have to use the console port to restore the default configuration file, and all of your configuration changes will be lost.
Figure 211 Example: Enter the Management Password Password: 1234 230 Logged in Transfer the firmware file to the IES-612-51A. The firmware file on your computer (that you want to put onto the IES-612-51A is named IES-612-51A is named Figure 212 Example: Transfer the Firmware File ftp>...
H A P T E R This chapter covers Simple Network Management Protocol (SNMP) with the IES-612-51A. 51.1 SNMP Commands Use these commands to configure SNMP settings. See information about SNMP. 51.1.1 Get Community Command Syntax: ras> sys snmp getcommunity <community>...
Use this command to add the host IP address to the list of trusted hosts. If you enter a trusted host, your IES-612-51A will only respond to SNMP messages from this address. If you leave the trusted host set to 0.0.0.0 (default), the IES-612-51A will respond to all SNMP messages it receives, regardless of source.
52.1.2 DSL Port Enable Command Syntax: ras> adsl enable <portlist> IES-612-51A User’s Guide ADSL Commands Chapter 13 on page 107 You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>.
DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. A profile name. IES-612-51A User’s Guide...
<up max margin> = <up min rate> <down target margin> <down min margin> IES-612-51A User’s Guide up stream down stream --------- ----------- 2048 The descriptive name for the profile. The latency mode. With interleave, you must also define the upstream and downstream delay (1-255 ms). It is recommended that you configure the same delay for both upstream and downstream.
32000 Kbps). The upstream down shift noise margin (0~31 in dB). The upstream up shift noise margin (0~31 in dB). The downstream down shift noise margin (0~31 in dB). The downstream up shift noise margin (0~31 in dB). IES-612-51A User’s Guide...
1200 24000 5 0 30 128 5 0 30 256 0 6 0 6 After you create a DSL profile, you can assign it to any of the DSL ports on the IES-612-51A. 52.1.6 DSL Port Profile Delete Command Syntax: ras>...
DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. A descriptive name for the port. You can use up to 31 printable ASCII characters (including spaces and hyphens). mode auto mode to make the modem t1413 IES-612-51A User’s Guide...
<portlist> < f5> <vpi> <vci> This command has the IES-612-51A perform an OAMF5 loopback test on the specified DSL port(s). The following example has the IES-612-51A perform an OAMF5 loopback test on DSL port 1’s PVC at VPI 0 and VCI 33.
= tones 0~31 <m0> = tones 32~63 <m1> The hexadecimal digit is converted to binary and a '1' disables the corresponding tone. Disabling a carrier tone turns it off so the system does not send data on it. IES-612-51A User’s Guide...
The hexadecimal digit is converted to binary and a '1' masks (disables) the corresponding tone. Disabling a carrier tone turns it off so the system does not send data on it. IES-612-51A User’s Guide The downstream carrier tones to be masked (disabled). Each <...
[<max_l2rate> <min_l2rate> <l0tol2_rate>] where <portlist> <l0time> <l2time> IES-612-51A User’s Guide ds carrier You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>.
L0 Time. The system changes back from L2 mode to L0 mode when the downstream transfer rate goes above this threshold. This rate must be less than or equal to one half of the Min L2 Rate and at least 16 Kbps. IES-612-51A User’s Guide...
<portlist> The following example turns off the Annex L feature for port 5. IES-612-51A User’s Guide Sets the minimum upstream (us) impulse noise protection setting. Use 0~3 to define a number of DMT symbols. 0 = 0 DMT symbols, 1 = 0.5 DMT symbols, 2 = 1 DMT symbols, 3 = 2 DMT symbols.
With Annex I, the DSL connection uses the full spectrum of the physical line and the user can not use POTS or ISDN service. Syntax: ras> adsl annexi enable <portlist> The following example turns on the Annex I feature for port 5. IES-612-51A User’s Guide...
---- ------ -------- ------------- -------------- --------------------- adsl2 IES-612-51A User’s Guide You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>.
(from the subscriber’s DSL modem or router to the IES-612-51A). “downstream carrier load” displays the number of bits received per DMT tone for the downstream channel (from the IES-612-51A to the subscriber’s DSL modem or router). The bit allocation contents are only valid when the link is up.
DSL modem or router is or the more interference there is on the line, the higher the power will be. “DS” refers to the power output of the IES-612-51A “US” refers to the power output of the subscriber’s DSL modem or router.
Chapter 52 ADSL Commands atuc information – Central), in this case IES-612-51A, during negotiation/provisioning message interchanges. atur information – Remote), in this case the subscriber’s DSL modem or router, during negotiation/provisioning message interchanges. This information can help in identifying the subscriber’s DSL modem or router.
IES-612-51A User’s Guide You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. Specify for which 15-minute interval (0~96) you want to display performance statistics.
This command displays line performance statistics for the current and previous 24 hours. DESCRIPTION Upstream. These statistics are for the connection (or traffic) coming from the subscriber’s device to the IES-612-51A. Downstream. These statistics are for the connection (or traffic) going from the IES-612-51A to the subscriber’s device.
Syntax: ras> adsl linediag setld <port number> This command has the IES-612-51A perform line diagnostics on the specified port. The DSL port must be set to ADSL2 or ADSL2+ operational mode and have a connection. It takes about one minute for the line diagnostics to finish.
DSL connection is using. The channel characteristics function is represented in linear format by a scale factor and a complex number. These are the maximum upstream and downstream scale factors used in producing the channel characteristics function. IES-612-51A User’s Guide...
DMT sub-carrier’s SNR is the ratio between the received signal power and the received noise power. The signal-to-noise ratio margin is the maximum that the received noise power could increase with the IES-612-51A still being able to meet its transmission targets.
This is the upstream and downstream Line Attenuation (in dB). This is the upstream and downstream Signal Attenuation (in dB). SNR(dB) 42.0 44.5 46.5 51.5 52.0 54.5 56.5 56.5 56.5 56.5 57.0 57.0 57.0 57.5 IES-612-51A User’s Guide...
Syntax: ras> adsl linediag setselt <port number> This command has the IES-612-51A perform a single end line test on the specified port. This test checks the distance to the subscriber’s location. The port must have an open loop. There cannot be a DSL device, phone, fax machine or other device connected to the subscriber’s end of the telephone...
G.992.3 standard. You do not need to use the line diagnostics set command first. Use the tone diagnostics to analyze problems with the physical DSL line. cableType loopEstimateLength INPROGRESS 24AWG 0 m(0.00 kFt) cableType loopEstimateLength DONE 24AWG 0 m(0.00 kFt) IES-612-51A User’s Guide...
DMT sub-carrier’s SNR is the ratio between the received signal power and the received noise power. The signal-to-noise ratio margin is the maximum that the received noise power could increase with the IES-612-51A still being able to meet its transmission targets.
The SNR can be used in analyzing time dependent changes in crosstalk levels and line attenuation (such as those caused by temperature variations and moisture). The name of an alarm profile. ATU-C ---------- ---------- (sec): (sec): (sec): (sec): (bps): (bps): (bps): (bps): (sec): (sec): ATU-R IES-612-51A User’s Guide...
IES-612- 51A. Downstream. These parameters are for the connection (or traffic) going from the IES-612-51A to the subscriber’s device. The number of Loss Of Frame seconds that are permitted to occur within 15 minutes.
<atur ses> <atuc uas> <atur uas> This command configures settings and thresholds that define when the IES-612-51A is to send an alarm trap and generate a syslog entry. Configure alarm profiles first and then use the 612-51A to use them with specific DSL ports.
[profile] where [profile] Displays which alarm profiles the IES-612-51A is set to use for specific (or all) DSL ports. The following example displays which alarm profile the IES-612-51A is set to use for DSL port 5.
<vcprofile> <vc|llc> <ubr|cbr> <pcr> <cdvt> ras> adsl vcprofile set <vcprofile> <vc|llc> <vbr(rt-vbr)|nrt-vbr> <pcr> <cdvt> <scr> <bt> IES-612-51A User’s Guide Commands for background information on virtual channels and ATM QoS. The name of the virtual channel profile (up to 31 ASCII characters).
This command creates a virtual channel profile. After you create a virtual channel profile, you can assign it to any of the DSL ports on the IES-612-51A. The following example creates a virtual channel profile named gold that uses LLC encapsulation.
53.3.1 PVC Show Command Syntax: ras> adsl pvc show [portlist] [<vpi> <vci>] IES-612-51A User’s Guide Chapter 53 Virtual Channel Management Commands The name of the virtual channel profile (up to 31 ASCII characters). You cannot delete the DEFVAL or...
One port can have only one super channel. The default VID (1 to 4094). Each PVC must have a unique VID since the IES-612-51A forwards traffic back to the subscribers based on the VLAN ID. You must assign a default VID (1 to 4094) and IEEE 802.1p default priority (0 to 7) to normal channels.
A PPVC (Priority-based PVC) allows you to give different priorities to PVCs that are members of the same VLAN. The IES-612-51A uses eight priority queues (also called levels) for the member PVCs. The system maps frames with certain IEEE 802.1p priorities to a PVC with a particular priority queue.
The following example creates a PPVC with VPI 8 and VCI 35 for port 5. The PPVC uses llc encapsulation and default VID 25. Any frames received without an IEEE 802.1p priority tag will be assigned a priority of 3. The IES-612-51A uses this PVC channel internally. This PVC is not needed on the subscriber’s device.
IES-612-51A User’s Guide Chapter 53 Virtual Channel Management Commands Assign a VC profile to use for policing this channel’s upstream traffic. The IES-612-51A does not perform upstream traffic policing if you do not specify an upstream VC profile. The priority queue (0~7) to use for this PVCs traffic. 7 is the highest priority.
You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. The VPI of the PPVC. The VCI of the PPVC. IES-612-51A User’s Guide...
PVC that connects to a subscriber device that uses 2684 routed mode. You can also specify the gateway to which the IES-612-51A sends the traffic and the VLAN ID tag to add. See RFC-2684 for details on routed mode traffic carried over AAL type 5 over ATM.
IP address 192.168.20.101. The subscriber’s device (the CPE) is connected to DSL port 1 on the IES-612-51A and the 2684 routed mode traffic is to use the PVC identified by VPI 8 and VCI 35. The CPE device’s WAN IP address is 192.168.10.200. The routed domain is the LAN IP addresses behind the CPE device.
• The IES-612-51A’s management IP address should not be in the same subnet as the one defined by the WAN IP address and netmask of the subscriber’s device. It is suggested that you set the netmask of the subscriber’s WAN IP address to 32 to avoid this problem.
DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. The VPI of the RPVC. The VCI of the RPVC. Assign a VC profile to use for this channel’s downstream traffic shaping. IES-612-51A User’s Guide...
IES-612-51A User’s Guide Chapter 53 Virtual Channel Management Commands Assign a VC profile to use for policing this channel’s upstream traffic. The IES-612-51A does not perform upstream traffic policing if you do not specify an upstream VC profile. The subscriber’s CPE WAN IP address in dotted decimal notation.
DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. The VPI of the RPVC. The VCI of the RPVC. The port of the RPVC. Specify a single DSL port <1>. The VPI of the RPVC. The VCI of the RPVC. IES-612-51A User’s Guide...
The following example adds a domain for a CPE device is connected to DSL port 1 on the IES-612-51A and the 2684 routed mode traffic is to use the PVC identified by VPI 8 and VCI 35. The CPE device’s LAN IP address is 10.10.10.10 and uses a subnet mask of 255.255.255.0.
The following example removes a domain for a CPE device is connected to DSL port 1 on the IES-612-51A and the 2684 routed mode traffic is to use the PVC identified by VPI 8 and VCI 35. The CPE device’s LAN IP address is 10.10.10.10 and uses a subnet mask of 255.255.255.0.
192.168.10.102 53.7.14 RPVC ARP Flush Command Syntax: ras> adsl rpvc arp flush IES-612-51A User’s Guide Chapter 53 Virtual Channel Management Commands The number of seconds (10~10000) the device is to keep the Address Resolution Protocol table’s entries of IP addresses of 2684 routed mode gateways.
Assign a VC profile to use for this channel’s downstream traffic shaping. Assign a VC profile to use for policing this channel’s upstream traffic. The IES-612-51A does not perform upstream traffic policing if you do not specify an upstream VC profile.
This command displays the PPPoA-to-PPPoE PVC settings for the specified port(s) or PVCs. The following example displays the settings for port 1. IES-612-51A User’s Guide Chapter 53 Virtual Channel Management Commands This field is optional. Specify the hostname of a remote...
The VCI of the PAE PVC. The port number of the PAE PVC. You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. IES-612-51A User’s Guide...
51A from the CPE (client) device. The number of echo-reply PDUs received by the IES-612- 51A from the CPE (client) device. The number of padi PDUs sent by the IES-612-51A to the BRAS. The number of pado PDUs sent by the BRAS to the IES- 612-51A.
The number of other types of errors that occur in the PPPoE session between the IES-612-51A and the BRAS. The port number of the TLS PVC. You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>.
Assign a VC profile to use for this channel’s downstream traffic shaping. Assign a VC profile to use for policing this channel’s upstream traffic. The IES-612-51A does not perform upstream traffic policing if you do not specify an upstream VC profile.
• etype <etype> smac <mac> • etype <etype> dmac <mac> • vlan < vid > smac <mac> • vlan < vid > dmac <mac> IES-612-51A User’s Guide ACL Commands The name of the ACL profile. The rule that classifies traffic flows. See below.
= Sets the ToS (Type of Service) range between 0 and 255. = Source port range (0~65535). = Destination port range (0~65535). or user ospf igmp icmp profile acl is not allowed. For this example, for traffic from VLAN 10 test IES-612-51A User’s Guide...
<name> This command lists the names of every ACL profile or displays the detailed settings of the specified ACL profile. IES-612-51A User’s Guide The name of the ACL profile. The name of the ACL profile. The name of the ACL profile.
<1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>. The VPI of the PVC. The VCI of the PVC. The name of the ACL profile. IES-612-51A User’s Guide...
---- --- ----- ---- -------------------------------- 33 PVC IES-612-51A User’s Guide The port number of the PVC. You can specify a single DSL port <1>, all DSL ports <*> or a list of DSL ports <1,3,5>. You can also include a range of ports <1,5,6~10>.
The LED itself or the unit may be faulty; contact your vendor. 55.2 The ALM LED Is On The ALM (alarm) LED lights when the IES-612-51A is overheated or the voltage readings are outside the tolerance levels. Table 100 ALM LED Troubleshooting...
IES-612-51A’s DSL port’s data rates are set high enough. Check the VLAN configuration. Ping the IES-612-51A from the computer behind the DSL modem or router. topology and enable RSTP, it is possible for RSTP to disable Ethernet port 1 (the uplink port).
If using a different port does not work, try a different DSL modem or router with the original port. 55.6 There Is No Voice on a DSL Connection The IES-612-51A has internal splitters and CO side Telco-50 connectors that allow the telephone wiring used for DSL connections to also simultaneously carry normal voice conversations.
Disconnect the telephone wire from USER. Connect a telephone to USER (see 56.5 on page 425 If there is no dial tone, your device’s internal splitter may be faulty, contact your vendor. Section 56.5 on page 425 for the proper pin assignments). for the Section IES-612-51A User’s Guide...
Check the VLAN configuration (see Check the cable and connections between the IES-612-51A and the local server. Try to access another local server. If data can be transmitted to a different local server, the local server that could not be accessed may have a problem.
Ping the IES-612-51A from the SNMP server. If you cannot, check the cable, connections and IP configuration. Check to see that the community (or trusted host) in the IES-612-51A matches the SNMP server’s community. Make sure that your computer’s IP address matches a configured trusted host IP address (if configured).
IES-612-51A uses for Telnet. Ping the IES-612-51A from your computer. If you are able to ping the IES-612-51A but are still unable to telnet, contact the distributor. If you cannot ping the IES-612-51A, check the cable, connections and IP configuration.
IES-612-51A’s console port. Turn the IES-612-51A off and then on to begin a session. When you turn on the IES-612-51A again you will see the initial screen. When you see the message...
• No parity, 8 data bits, 1 stop bit • No flow control 3 Turn off the IES-612-51A and turn it back on to restart it and begin a session. 4 When you see the message , press a key to enter debug mode.
H A P T E R Product Specifications This chapter provides the specifications for the IES-612-51A. 56.1 Device Specifications The following tables summarize the IES-612-51A’s hardware features. Table 112 Hardware Specifications FEATURE Dimensions Weight Power Specification Interface Connectors Stacking Rackmounting...
Chapter 56 Product Specifications Table 112 Hardware Specifications (continued) FEATURE Fans Certifications 56.2 Firmware Features This section introduces the IES-612-51A firmware features. Table 113 IES-612-51A Features Basic Function Management Interfaces In-band Ethernet management Management Features DESCRIPTION 1 fan RoHS WEEE...
Page 419
Table 113 IES-612-51A Features (continued) Alarm, System Monitoring, Security and Logging ADSL2/2+ SNMP Management IES-612-51A User’s Guide Alarm Automatic alarm and status report Programmable alarm filters Severity level configurable for each alarm Threshold levels configurable per port LED indication of alarm state...
Page 420
Chapter 56 Product Specifications Table 113 IES-612-51A Features (continued) MIBs VLAN Quality of Service Layer 2 Bridging SNMP MIB-II (RFC 1213) Bridge MIBs (RFC 1493, 2674) Ethernet MIB Q MIB ADSL line MIB (RFC 2662) ADSL Extension Line MIB (RFC2449)
Page 421
Table 113 IES-612-51A Features (continued) Multicast Features ACL/Filtering IES-612-51A User’s Guide Static or dynamic (IGMP) multicast setting IGMP proxy IGMP snooping v1&v2 (port based) IGMP filtering per DSL port IGMP bandwidth limiting per DSL port IGMP group count limiting per DSL port...
Chapter 56 Product Specifications Table 113 IES-612-51A Features (continued) Per ADSL Port Provisioning System-wide Provisioning 56.3 Standards Supported The following list, which is not exhaustive, illustrates the standards supported in the IES-612- 51A. Table 114 Standards Supported STANDARD RFC 867...
ITU G.992.2 (G. Lite) ITU G.992.3 (G.dmt.bis) ITU G.992.3 (G.lite.bis) ITU G.992.5 (ADSL2+) 1.363.5 56.4 Default Settings This section lists the default configuration of the IES-612-51A. Table 115 Default Settings Default Login Settings Default IP Address Default Subnet Mask Default User Name...
Page 424
DEFVAL (factory default) RFC 2684 LLC-based 300000 cells/second RFC 2684 VC-based 300000 cells/second The DEFVAL IGMP filter profile is assigned to all of the DSL ports by default. It allows a port to join all multicast IP addresses (224.0.0.0~239.255.255.255). IES-612-51A User’s Guide...
The IES-612-51A DSL ports’ PVCs use ATM Adaptation Layer (AAL) 5. 56.5 Hardware Telco-50 Connector Pin Assignments The following diagram shows the pin assignments of the Telco-50 connector. Figure 298 Telco-50 Pin Assignments This table lists the ports and matching pin numbers for the hardware Telco-50 connector.
Appendices and Index The appendices provide general information. Some details may not apply to your IES-612-51A. Legal Information (429) Customer Support (433) Index (439)
ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved.
Page 430
ZyXEL. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. IES-612-51A User’s Guide...
Page 431
Registration Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. IES-612-51A User’s Guide Appendix A Legal Information...
Page 432
Appendix A Legal Information IES-612-51A User’s Guide...
Appendix B Customer Support • Regular Mail: ZyXEL Communications, Czech s.r.o., Modranská 621, 143 01 Praha 4 - Modrany, Ceská Republika Denmark • Support E-mail: support@zyxel.dk • Sales E-mail: sales@zyxel.dk • Telephone: +45-39-55-07-00 • Fax: +45-39-55-07-07 • Web: www.zyxel.dk • Regular Mail: ZyXEL Communications A/S, Columbusvej, 2860 Soeborg, Denmark Finland •...
Page 435
• Regular Mail: ZyXEL Malaysia Sdn Bhd., 1-02 & 1-03, Jalan Kenari 17F, Bandar Puchong Jaya, 47100 Puchong, Selangor Darul Ehsan, Malaysia North America • Support E-mail: support@zyxel.com • Support Telephone: +1-800-978-7222 • Sales E-mail: sales@zyxel.com • Sales Telephone: +1-714-632-0882 • Fax: +1-714-632-0858 • Web: www.zyxel.com IES-612-51A User’s Guide Appendix B Customer Support...
Page 436
Appendix B Customer Support • Regular Mail: ZyXEL Communications Inc., 1130 N. Miller St., Anaheim, CA 92806- 2001, U.S.A. Norway • Support E-mail: support@zyxel.no • Sales E-mail: sales@zyxel.no • Telephone: +47-22-80-61-80 • Fax: +47-22-80-61-81 • Web: www.zyxel.no • Regular Mail: ZyXEL Communications A/S, Nils Hansens vei 13, 0667 Oslo, Norway Poland •...
ATM traffic class 128, 132 authentication default privilege level for administrators modes for administrators user IES-612-51A User’s Guide back up configuration bit allocation Bridge Protocol Data Units (BPDU) Burst Tolerance (BT) Canonical Format Indicator (CFI) Cell Delay Variation Tolerance (CDVT)
Page 440
IGMP Filter Profile Screen IGMP snooping initial configuration Installation Rack-Mounted Installation Requirements interleave delay 108, 126 interleave mode Internet Explorer 61, 69 Internet Group Multicast Protocol. See IGMP. Internet Protocol. See IP. ip commands IP Setup IES-612-51A User’s Guide...
Page 441
Mounting Brackets multicast MAC address Multicast VLAN. See MVLAN. MVLAN Near End Block Errors (NEBE) NetBIOS Network Basic Input/Output System. See NetBIOS. IES-612-51A User’s Guide non real-time Variable Bit Rate (nrt-VBR) NTP (RFC-1305) OAM F5 Loopback option 82 packet filter password Peak Cell Rate (PCR) Permanent Virtual Circuit.
Page 442
Switch Setup switch vlan commands syntax conventions sys commands SYS LED troubleshooting sys snmp commands syslog System Information system log IES-612-51A User’s Guide...
Page 443
Unspecified Bit Rate (UBR) up time upstream (traffic) User Account Variable Bit Rate (VBR) VC Mux VC Profile Screen VC Setup IES-612-51A User’s Guide vendor information ventilation holes virtual channel downstream profile profile upstream profile Virtual Circuit Identifier (VCI) Virtual Circuit. See VC.