Changing A Group Of Numeric Data Values; Infinitely Variable Change Of Numeric Data Value; Value, Step-By-Step; Readout And Programming Of Indexed Parameters - Danfoss VLT AQUA Drive FC 202 Programming Manual

How to Programme
2.2.12 Changing a Group of Numeric Data
Values
2 2
If the selected parameter represents a numeric data value,
change the data value using the [
▲
well as the [
move the cursor horizontally.
Illustration 2.17 Changing a Group of Numeric Data Values
▲ ▼
Press [ ] [ ] keys to change the data value. [
the data value, and [
cursor on the value to save and press [OK].
Illustration 2.18 Changing a Group of Numeric Data Values
2.2.13 Infinitely Variable Change of
Numeric Data Value
If the selected parameter represents a numeric data value,
select a digit with [
Illustration 2.19 Selecting a Digit
Change the selected digit infinitely variably with [
The selected digit is indicated by the cursor. Place the
cursor on the digit to save and press [OK].
22
◀ ▶
] [ ] navigation keys as
▼ ◀
] [ ] navigation keys. Press [
113 RPM 1.78 A
Load depen. setting
1 - 60 Low speed load
compensation
100%
▼
] decreases the data value. Place the
729RPM 6.21A
Load depen. setting
1 - 60 Low speed load
compensation
1 0% 6
◀ ▶
] [ ].
635 RPM 0.44 A
Start Adjustments
1 - 71 Start Delay
00.0s
Danfoss A/S © Rev. 2014-01-21 All rights reserved.
Programming Guide
▶
] [ ] keys to
Illustration 2.20 Saving
1(1)

2.2.14 Value, Step-by-Step

1- 6*
Certain parameters can be changed step by step. This
applies to parameter 1-20 Motor Power [kW], 1-22 Motor
Voltage and parameter 1-23 Motor Frequency.
The parameters are changed both as a group of numeric
data values and as numeric data values that are infinitely
varying.
2.2.15 Readout and Programming of
▲
] increases
Parameters are indexed when placed in a rolling stack.
15-30 Alarm Log: Error Code to parameter 15-32 Alarm Log:
Time contain a fault log which can be read out. Select a
1(1)
1- 6*
parameter, press [OK], and press the keys [
through the value log.
For example, this is how 3-10 Preset Reference is changed:
Select the parameter, press [OK], and press [
through the indexed values. To change the parameter
value, select the indexed value and press [OK]. Change the
value by pressing [
setting. Press [Cancel] to abort. Press [Back] to leave the
parameter.
2.3 How to Programme on the Numerical
LCP
The following instructions are valid for the Numerical LCP
(LCP 101).
1 (1)
The control panel is divided into 4 functional groups:
1- 7*
1.
2.
3.
4.
▲ ▼
] [ ].
Display line: Status messages displaying icons and
numeric value
Indicator lights (LEDs)
•
•
•
957RPM 11.58A
Start Adjustments
1-71 High starting torque time
0. s 4
Indexed Parameters
▲ ▼
] [ ]. Press [OK] to accept the new
Numerical display.
Menu keys and indicator lights - changing
parameters and switching between display
functions.
Navigation keys and indicator lights (LEDs).
Operation keys and indicator lights (LEDs).
Green LED/On: Indicates if control section is on.
Yellow LED/Wrn.: Indicates a warning.
Flashing red LED/Alarm: Indicates an alarm.
1 (1)
1-7*
▲ ▼
] [ ] to scroll
▲ ▼
] [ ] to scroll
MG20O702