Danfoss VLT AQUA Drive FC 202 Programming Manual page 41

Parameter Description
1-06 Clockwise Direction
Option: Function:
NOTICE
This parameter cannot be adjusted while the
motor is running.
This parameter defines the term "Clockwise"
corresponding to the LCP direction arrow. Used for
easy change of direction of shaft rotation without
swapping motor wires.
[0] Normal Motor shaft turns in clockwise direction when the
frequency converter is connected U⇒U; V⇒V, and
W⇒W to motor.
[1] Inverse Motor shaft turns in counter clockwise direction
when the frequency converter is connected U⇒U;
V⇒V, and W⇒W to motor.
3.3.2 1-10 Motor Selection
NOTICE
This parameter group cannot be adjusted while the
motor is running.
The following parameters are active ('x') depending on
the setting of parameter 1-10 Motor Construction
Parameter 1-10 Motor
Construction
Parameter 1-00 Configuration
Mode
Parameter 1-03 Torque Charac-
teristics
Parameter 1-06 Clockwise
Direction
Parameter 1-14 Damping Gain
Parameter 1-15 Low Speed Filter
Time Const.
Parameter 1-16 High Speed Filter
Time Const.
Parameter 1-17 Voltage filter
time const.
Parameter 1-20 Motor Power
[kW]
Parameter 1-21 Motor Power [HP]
Parameter 1-22 Motor Voltage
Parameter 1-23 Motor Frequency
Parameter 1-24 Motor Current
Parameter 1-25 Motor Nominal
Speed
Parameter 1-26 Motor Cont.
Rated Torque
MG20O702
Programming Guide
[1] PM Motor
[0] Asynchron
non-salient
x x
x
x x
x
x
x
x
x
x
x
x
x x
x x
x
Danfoss A/S © Rev. 2014-01-21 All rights reserved.
Parameter 1-10 Motor
Construction
Parameter 1-28 Motor Rotation
Check
Parameter 1-29 Automatic Motor
Adaptation (AMA)
Parameter 1-30 Stator Resistance
(Rs)
Parameter 1-31 Rotor Resistance
(Rr)
Parameter 1-35 Main Reactance
(Xh)
Parameter 1-37 d-axis Inductance
(Ld)
Parameter 1-39 Motor Poles
Parameter 1-40 Back EMF at 1000
RPM
Parameter 1-50 Motor Magneti-
sation at Zero Speed
Parameter 1-51 Min Speed
Normal Magnetising [RPM]
Parameter 1-52 Min Speed
Normal Magnetising [Hz]
Parameter 1-58 Flystart Test
Pulses Current
Parameter 1-59 Flystart Test
Pulses Frequency
Parameter 1-60 Low Speed Load
Compensation
Parameter 1-61 High Speed Load
Compensation
Parameter 1-62 Slip Compen-
sation
Parameter 1-63 Slip Compen-
sation Time Constant
Parameter 1-64 Resonance
Damping
Parameter 1-65 Resonance
Damping Time Constant
Parameter 1-66 Min. Current at
Low Speed
Parameter 1-70 PM Start Mode
Parameter 1-71 Start Delay
Parameter 1-72 Start Function
Parameter 1-73 Flying Start
Parameter 1-80 Function at Stop
Parameter 1-81 Min Speed for
Function at Stop [RPM]
Parameter 1-82 Min Speed for
Function at Stop [Hz]
Parameter 1-86 Trip Speed Low
[RPM]
Parameter 1-87 Trip Speed Low
[Hz]
[1] PM Motor
[0] Asynchron
non-salient
x x
x
x x
x
x
x
x x
x
x
x
x
x x
x x
x
x
x
x
x
x
x
x
x x
x x
x x
x x
x x
x x
x x
x x
39
3 3