Control Mode Dependent Parameter Default Values; Control Mode Dependent Parameter Default Values; A1-02 (Motor 1 Control Mode) Dependent Parameters - YASKAWA AC Drive-A1000 Technical Manual

B.16 Control Mode Dependent Parameter Default Values
B.16 Control Mode Dependent Parameter Default Values
The tables below list parameters that depend on the control mode selection (A1-02 for motor 1, E3-01 for motor 2). Changing
the control mode initializes these parameters to the values shown here.
u

A1-02 (Motor 1 Control Mode) Dependent Parameters

Table B.2 A1-02 (Motor 1 Control Mode) Dependent Parameters and Default Values
No. Name
b2-01 DC Injection Braking Start Frequency
b2-04 DC Injection Braking Time at Stop
b3-01 Speed Search Selection at Start
b3-02 Speed Search Deactivation Current
b3-14 Bi-Directional Speed Search Selection
b8-01 Energy Saving Control Selection
b8-02 Energy Saving Gain
b8-03 Energy Saving Control Filter Time Constant
C2-01 S-Curve Time at Acceleration Start
C3-01 Slip Compensation Gain
C3-02 Slip Compensation Primary Delay Time
C4-01 Torque Compensation Gain
C4-02 Torque Compensation Primary Delay Time
C5-01 ASR Proportional Gain 1
C5-02 ASR Integral Time 1
C5-03 ASR Proportional Gain 2
C5-04 ASR Integral Time 2
C5-06 ASR Primary Delay Time Constant
C6-02 Carrier Frequency Selection
E1-04 Maximum Output Frequency
E1-05 Maximum Voltage
E1-06 Base Frequency
E1-07 Middle Output Frequency
E1-08 Middle Output Frequency Voltage
E1-09 Minimum Output Frequency
E1-10 Minimum Output Frequency Voltage
F1-01 PG 1 Pulses Per Revolution
F1-05 PG 1 Rotation Selection
F1-09 Overspeed Detection Delay Time
L1-01 Motor Overload Protection Selection
L3-20 DC Bus Voltage Adjustment Gain
L3-21 Accel/Decel Rate Calculation Gain
L4-02 Speed Agreement Detection Width
L4-04 Speed Agreement Detection Width (+/-)
L8-38 Carrier Frequency Reduction Selection
Carrier Frequency Reduction Off Delay
L8-40
Time
o1-03 Digital Operator Display Selection
o1-04 V/f Pattern Display Unit
<1> Default setting is dependent on parameters C6-01, Drive Duty Selection, and o2-04, Drive Model Selection.
456
Setting Range Resolution
0.0 to 10.0 0.1 Hz
0.00 to 10.00 0.01 s
0 to 1 –
0 to 200 1%
0 to 1 1
0 to 1 –
0.0 to 10.0 0.1
0.00 to 10.00 0.01 s
0.00 to 10.00 0.01 s
0.0 to 2.5 0.1
0 to 10000 1 ms
0.00 to 2.50 0.01
0 to 10000 1 ms
0.00 to 300.00 0.01
0.000 to 10.000 0.001 s
0.00 to 300.00 0.01
0.000 to 10.000 0.001 s
0.000 to 0.500 0.001 s
1 to F –
40.0 to 400.0 0.1 Hz
0.0 to 733.1 0.1 V
0.0 to 400.0 0.1 Hz
0.0 to 400.0 0.1 Hz
0.0 to 733.1 0.1 V
0.0 to 400.0 0.1 Hz
0.0 to 733.1 0.1 V
0 to 60000 1 ppr
0 to 1 –
0.0 to 2.0 0.1 s
0 to 4 –
0.00 to 5.00 0.01
0.00 to 10.00 0.01
0.0 to 20.0 0.1 Hz
0.0 to 20.0 0.1 Hz
0 to 2 1
0.00 to 2.00 0.01 s
0 to 3 1
0 to 1 1
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual
Control Modes (A1-02)
V/f (0) V/f w/PG (1) OLV (2)
0.5 0.5 0.5
0.50 0.50 0.50
0 1
120 – 100
1 0
0 0
– – 0.7
0.50
2.00 (Motor
– – Capacity: 55
kW and
above)
0.20 0.20 0.20
0.0 – 1.0
2000 – 200
1.00 1.00 1.00
200 200 20
– 0.20
– 0.200
– 0.02
– 0.050
– –
<1> <1>
7 7 7
60.0 60.0 60.0
575 575 575
60.0 60.0 60.0
3.0 3.0 3.0
15.0 15.0 15.0
1.5 1.5 0.5
9.0 9.0 2.0
600 600 600
0 0
– 1.0
1 1
1.00 1.00 0.30
1.00 1.00 1.00
2.0 2.0 2.0
2.0 2.0 2.0
<1> <1> <1>
0.50 0.50 0.50
0 0
— — —
CLV (3)
0.5
0.50
0 1
–
1 1
0 0
1.0
0.01
0.05 (Motor
Capacity: 55
kW and
above)
0.20
1.0
–
–
–
– 20.00
– 0.500
– 20.00
– 0.500
– 0.004
<1> <1>
7
60.0
575
60.0
3.0
15.0
0.0
0.0
600
0 0
– 0.0
1 1
0.30
1.00
2.0
2.0
<1>
0.50
0 0
0