YASKAWA AC Drive-A1000 Technical Manual page 526

Index
oL3.......................................................................... 310, 321
oL4.......................................................................... 310, 321
oL5.......................................................................... 310, 321
oL7................................................................................ 311
Online Tuning Gain ............................................................ 275
Online Tuning Selection ....................................................... 274
oPE ............................................................................... 324
oPE01 ............................................................................ 324
oPE02 ............................................................................ 324
oPE03 ............................................................................ 324
oPE04 ............................................................................ 325
oPE05 ............................................................................ 325
oPE06 ............................................................................ 325
oPE07 ............................................................................ 325
oPE08 ............................................................................ 326
oPE09 ............................................................................ 326
oPE10 ............................................................................ 326
oPE11 ............................................................................ 327
oPE13 ............................................................................ 327
oPE15 ............................................................................ 327
oPE16 ............................................................................ 327
oPE18 ............................................................................ 327
oPE Fault Parameter............................................................ 449
Open Loop Vector Control ....................................30, 291, 340, 342
Open Loop Vector Control for IPM Motors ..................................30
Open Loop Vector Control for PM Motors ...................................30
Open Loop Vector Control Mode Tuning ................................... 291
Open Loop Vector Control Mode Tuning Parameters ......... 291, 292, 293
Operating with the Load Connected.......................................... 114
Operation Errors .......................................................... 295, 298
Operation Selection at Deviation (dEv)...................................... 197
Operation Selection at Overspeed (oS) ...................................... 196
Operation Selection at PG Open Circuit (PGo)............................. 196
Operation Selection when Digital Operator is Disconnected ....... 281, 441
Operation Status Monitors..................................................... 284
Operation with Permanent Magnet Motors..................................... 3
Operator Programming Errors ................................................ 324
Operator Related Settings...................................................... 278
oPr ................................................................................ 311
Optional 24 V DC power supply connector cover ...........................35
Option Card Connection Error at Option Port CN5-A..................... 307
Option Card Connection Error at Option Port CN5-C..................... 308
Option card connector (CN5-A) ................................................36
Option card connector (CN5-B) ................................................36
Option card connector (CN5-C) ................................................36
Option card error occurred at option port CN5-A .......................... 307
Option card error occurred at option port CN5-B .......................... 307
Option card error occurred at option port CN5-C .......................... 308
Option Card External Fault.............................................. 303, 318
Option Card Fault at Option Port CN5-A ................................... 307
Option Card Fault at Option Port CN5-B.................................... 307
Option Card Fault at Option Port CN5-C.................................... 308
Option Card Installation ....................................................... 364
Option Communication Error ........................................... 300, 316
Option Frequency Reference .................................................. 453
Option Settings.................................................................. 196
oS ........................................................................... 311, 321
Oscillation or Hunting.......................................................... 341
Output Current .................................................................. 448
Output Current 1 During Speed Search...................................... 139
526
Output Current at Previous Fault ............................................. 450
Output Current Imbalance ..................................................... 305
Output Frequency............................................................... 448
Output Frequency after Soft Start ............................................ 449
Output Frequency at Previous Fault.......................................... 450
Output Frequency is not as High as Frequency Reference ................ 342
Output Frequency Reduction During Overheat Alarm .................... 264
Output Frequency Resolution ................................................. 374
Output Ground Fault Detection Selection ............................. 265, 434
Output of speed control (ASR) (for Simple V/f PG)....................... 454
Output Phase Loss .............................................................. 305
Output Phase Loss Protection ................................................. 433
Output Phase Loss Protection Selection ..................................... 264
Output Power.................................................................... 448
Output Power at Previous Fault............................................... 450
Output Terminal Status ........................................................ 449
Output Terminal Status at Previous Fault ................................... 451
Output Voltage at Previous Fault ............................................. 450
Output Voltage Detection Fault......................................... 315, 323
Output Voltage Limit........................................................... 277
Output Voltage Limit Operation Selection .................................. 158
Output Voltage Reference ..................................................... 448
Output Voltage Reference (Vd)............................................... 454
Output Voltage Reference (Vq)............................................... 454
ov............................................................................ 311, 321
Overcurrent ...................................................................... 306
Overcurrent Detection Gain ............................................. 266, 434
Overexcitation Deceleration................................................... 253
Overexcitation Deceleration Gain ...................................... 271, 437
Overexcitation Operation Selection .................................... 272, 437
Overheat 1 (Heatsink Overheat) .............................................. 308
Overheat Alarm Level.................................................... 225, 433
Overheat Pre-Alarm Operation Selection ............................. 227, 433
Overload Protection ............................................................ 375
Overload Tolerance............................................................. 373
Overspeed (for Control Mode with PG) ............................... 311, 321
Overspeed Detection Delay Time ............................................ 196
Overspeed Detection Level.................................................... 196
Overtorque 1..................................................................... 321
Overtorque 2..................................................................... 321
Overtorque Detection 1 ........................................................ 310
Overtorque Detection 2 ........................................................ 310
Overtorque Detection Operation.............................................. 259
Overvoltage...................................................................... 311
Overvoltage Protection......................................................... 375
Overvoltage Suppression Function ........................................... 254
Overvoltage Suppression Function Selection ............................... 254
ov Suppression Function Selection........................................... 429
P
Parameter Access Level........................................................ 115
Parameter Range Setting Error................................................ 324
Parameter Selection Error ..................................................... 326
Parameter Settings ................................................................85
Parameters for KEB Ride-Thru ............................................... 247
Parameters to Minimize Motor Hunting and Oscillation .................. 294
PASS ............................................................................. 322
Password ................................................................... 115, 122
Password Setting................................................................ 122
Password Settings............................................................... 115
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual