YASKAWA AC Drive-A1000 Technical Manual page 408

B.8 F: Options
No.
(Addr. Name
Hex)
F1-09 Overspeed Detection Delay
(388) Time
F1-10 Excessive Speed Deviation
(389) Detection Level
F1-11 Excessive Speed Deviation
(38A) Detection Delay Time
F1-12
PG 1 Gear Teeth 1
(38B)
F1-13
PG 1 Gear Teeth 2
(38C)
F1-14 PG Open-Circuit Detection
(38D) Time
F1-18
dv3 Detection Selection
(3AD)
F1-19
dv4 Detection Selection
(3AE)
F1-20 PG Option Card Disconnect
(3B4) Detection 1
F1-21
PG 1 Signal Selection
(3BC)
F1-30 PG Card Option Port for
(3AA) Motor 2 Selection
F1-31
PG 2 Pulses Per Revolution
(3B0)
F1-32
PG 2 Rotation Selection
(3B1)
F1-33
PG 2 Gear Teeth 1
(3B2)
408
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
Sets the time in seconds for an overspeed situation to trigger a fault (oS).
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
Sets the speed deviation detection level as a percentage of the maximum output
frequency.
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
Sets the time in seconds for a speed deviation situation to trigger a fault (dEv).
V/f V/f w PG V/f w PG OLV
OLV/PM AOLV/PM CLV/PM
Sets the gear ratio between the motor shaft and the encoder (PG).
A gear ratio of 1 will be used if F1-12 or F1-13 are set to 0.
V/f V/f w PG V/f w PG OLV
OLV/PM AOLV/PM CLV/PM
Sets the gear ratio between the motor shaft and the encoder (PG). A gear ratio
of 1 will be used if F1-12 or F1-13 are set to 0.
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
Sets the time required to trigger a PG Open fault (PGo).
V/f V/f V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
0: Disabled
n: Number of dv3 occurrences that must be detected to trigger a dv3 fault.
V/f V/f V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
0: Disabled
n: Number of pulses that the A and B pulse are reversed that triggers dv4
detection.
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
0: Disabled
1: Enabled
V/f V/f w PG V/f w PG OLV
OLV/PM AOLV/PM CLV/PM
0: A pulse detection
1: AB pulse detection
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM
Sets the port for the PG option card used by motor 2.
0: CN5-C
1: CN5-B
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM
Sets the number of pulses for a PG option card connected to port CN5-B.
V/f V/f V/f w PG V/f w PG V/f w PG V/f w PG OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM
0: Pulse A leads
1: Pulse B leads
V/f V/f w PG V/f w PG OLV
OLV/PM AOLV/PM CLV/PM
Sets the gear ratio between the motor shaft and the encoder (PG).
A gear ratio of 1 will be used if F1-33 or F1-34 are set to 0.
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual
Description
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV
CLV
CLV CLV CLV CLV
CLV CLV
CLV CLV
CLV CLV CLV CLV
CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV
Values Page
<1>
Default:
196
Min.: 0.0 s
Max.: 2.0 s
Default: 10%
Min.: 0 197
Max.: 50
Default: 0.5 s
Min.: 0.0 197
Max.: 10.0
Default: 0
Min.: 0 197
Max.: 1000
Default: 0
Min.: 0 197
Max.: 1000
Default: 2.0 s
Min.: 0.0 196
Max.: 10.0
Default: 10
Min.: 0 198
Max.: 10
Default: 128
Min.: 0 198
Max.: 5000
Default: 1
198
Range: 0, 1
Default: 0
198
Range: 0, 1
Default: 1
199
Range: 0, 1
Default: 1024 ppr
Min.: 0 196
Max.: 60000
Default: 0
197
Range: 0, 1
Default: 0
Min.: 0 197
Max.: 1000