Control Mode Dependent Parameter Default Values; Control Mode Dependent Parameter Default Values - YASKAWA T1000V Technical Manual

B.4 Control Mode Dependent Parameter Default Values
B.4 Control Mode Dependent Parameter Default Values
The tables below list parameters that depend on the control mode selection (A1-02 for motor 1, E3-01 for motor 2).
These parameters are initialized to the shown values if the control mode is changed.
Table B.1 A1-02 (Motor 1 Control Mode) Dependent Parameters and Default Values
Parameter
b2-03 DC Injection Braking Time at Start
b2-04 DC Injection Braking Time at Stop
b3-02 Speed Search Deactivation Current
C2-01 S-Curve Characteristic at Accel Start
C3-01 Slip Compensation Gain
C3-02 Slip Compensation Primary Delay Time
C4-01 Torque Compensation Gain
C4-02 Torque Compensation Primary Delay Time
C6-02 Carrier Frequency Selection
E1-04 Maximum Output Frequency
E1-05 Maximum Voltage
E1-06 Base Frequency
E1-07 Middle Output Frequency
E1-08 Middle Output Frequency Voltage
E1-09 Minimum Output Frequency
E1-10 Minimum Output Frequency Voltage
E1-11 Middle Output Frequency 2
E1-12 Mid Output Frequency Voltage 2
E1-13 Base Voltage
L1-01 Motor Overload Protection Selection
L8-18 Software Current Limit Selection
S6-04 Main Circuit Voltage Adjustment Gain
S6-05 Accel/Decel Calculation Gain
<9> Default setting is determined by the motor code set to parameter E5-01.
<11> Default setting is determined by the drive model selection set in parameter o2-04.
<17> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
Table B.2 E3-01 (Motor 2 Control Mode) Dependent Parameters and Default Values
Parameter
E3-04 Motor 2 Max Output Frequency
E3-05 Motor 2 Max Voltage
E3-06 Motor 2 Base Frequency
E3-07 Motor 2 Mid Output Frequency
E3-08 Motor 2 Mid Output Frequency Voltage
E3-09 Motor 2 Minimum Output Frequency
E3-10 Motor 2 Minimum Output Frequency Voltage
E3-11 Motor 2 Mid Output Frequency 2
E3-12 Motor 2 Mid Output Frequency Voltage 2
E3-13 Motor 2 Base Voltage
E4-14 Motor 2 Slip Compensation Gain
<17> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
Note: Motor 2 cannot be a PM motor.
364
Description
<17>
<17>
<17>
<17>
<17>
Description
<17>
<17>
<17>
<17>
Setting Range Resolution
0.00 to 10.00
0.00 to 10.00
0 to 200
0.00 to 10.00
0.0 to 2.5
0 to 10000
0.00 to 2.50
0 to 10000
1 to 6, F
40.0 to 400.0
0.0 to 255.0
0.0 to 400.0
0.0 to 400.0
0.0 to 255.0
0.0 to 400.0
0.0 to 255.0
0.0 to 400.0
0.0 to 255.0
0.0 to 255.0
0 to 4
0, 1
0.00 to 5.00
0.00 to 200.00
Setting Range
40.0 to 400.0
0.0 to 255.0
0.0 to 400.0
0.0 to 400.0
0.0 to 255.0
0.0 to 400.0
0.0 to 255.0
<17>
0.0 to 400.0
0.0 to 255.0
0.0 to 255.0
0.0 to 2.5
YASKAWA ELECTRIC SIEP C710606 44B YASKAWA AC Drive T1000V Technical Manual
Control Modes (A1-02)
V/f (0) OLV (2)
0.01 s 0.00
0.01 s 0.50
1% 120
0.01 s 0.20
0.1 0.0
1 ms 2000
0.01 1.00
1 ms 200
1
<11>
0.1 Hz 50.0
0.1 V 200.0
0.1 Hz 50.0
0.1 Hz 2.5
0.1 V 16.0
0.1 Hz 1.3
0.1 V 12.0
0.1 Hz 0.0
0.1 V 0.0
0.1 V 0.0
- 1
1 1
0.01 1.00
0.01 1.00
Control Modes (E3-01)
Resolution
V/f (0)
0.1 Hz 50.0
0.1 V 200.0
0.1 Hz 50.0
0.1 Hz 2.5
0.1 V 16.0
0.1 Hz 1.3
0.1 V 12.0
0.1 Hz 0.0
0.1 V 0.0
0.1 V 0.0
0.1 0.0
PM (5)
0.00 –
0.50 0.00
100 –
0.20 1.00
1.0 –
200 –
1.00 0.00
20 100
2
<11>
50.0
<9>
200.0
<9>
50.0
<9>
3.0 –
12.0 –
0.5
<9>
3.0 –
0.0 –
0.0 –
0.0 –
1 4
1 –
0.30 0.65
1.00 2.50
OLV (2)
50.0
200.0
50.0
3.0
14.4
0.5
2.5
0.0
0.0
0.0
1.0