YASKAWA AC Drive-A1000 Technical Manual page 528

Index
Pulse Train Input Bias.......................................................... 237
Pulse Train Input Filter Time ................................................. 237
Pulse Train Input Gain ......................................................... 237
Pulse Train Input Minimum Frequency...................................... 237
Pulse Train Input Scaling ...................................................... 236
Pulse Train Input Terminal RP Function Selection ........................ 235
Pulse Train Monitor Scaling .................................................. 237
Pulse Train Monitor Selection ................................................ 237
Q
q-axis ACR Output ............................................................. 454
R
R-....................................................................................63
R/L1 ................................................................................58
R+ ...................................................................................63
Ramp to stop .................................................................... 128
Rated Current Depending on Carrier Frequency ........................... 167
Rated Current Setting Alarm .................................................. 328
Rated Output Capacity ......................................................... 373
Rated Output Current........................................................... 373
Rated Slip Error ................................................................. 329
Rated Voltage, Rated Frequency ............................................. 373
rdEr ............................................................................... 333
READ ............................................................................ 281
rEAd .............................................................................. 333
Reading Drive MEMOBUS/Modbus Register Contents .................. 475
Reading Parameter Settings ................................................... 333
Reattaching the Digital Operator ...............................................56
Reattaching the Front Cover ....................................................56
Reattaching the Protective Cover...............................................57
Reattaching the Terminal Cover on an IP20/NEMA Type 1 Drive........55
REMOTE ..........................................................................89
Removing the Cooling Fan .................................................... 354
Removing the Digital Operator .................................................56
Removing the Front Cover ......................................................56
Removing the Protective Cover.................................................57
Removing the Terminal Cover on an IP20/NEMA Type 1 Drive..........55
Replacement Parts .............................................................. 351
Replacing the Drive ............................................................ 356
Reset Communication Parameters............................................ 203
RESET Key........................................................................79
Resistance Tuning Error ....................................................... 328
Response Messages from Drive to Master .................................. 472
Reverse Direction Output Example Time Chart............................ 225
Reverse Operation Selection .................................................. 130
Reverse Prohibited Error....................................................... 331
Reverse Regenerative Torque Limit ................................... 262, 433
Reverse Torque Limit .................................................... 262, 433
rF .................................................................................. 313
rH ................................................................................. 313
Rotational Auto-Tuning.................................................. 100, 103
Rotational Auto-Tuning for V/f Control..................................... 100
RP ...................................................................................62
rr................................................................................... 313
RS-422 Interface ................................................................ 467
RS-485 Interface ................................................................ 466
RTS Control Selection ......................................................... 469
Rubber Bushing ...................................................................35
rUn ................................................................................ 322
528
Run Command/Frequency Reference Source Selection Error............ 325
Run Command at Power Up................................................... 133
Run Command Method Selection ............................................ 470
Run Command Selection ...................................................... 337
Run Command Selection 1 .............................................. 127, 384
Run Command Selection 2 .................................................... 133
Run command selection while in Programming Mode .................... 132
Run Command Source Selection ............................................. 453
RUN Key ..........................................................................79
RUN LED..........................................................................81
RUN Light .........................................................................79
S
S- ....................................................................................63
S/L2.................................................................................58
S+ ...................................................................................63
S1 ...................................................................................61
S2 ...................................................................................61
S3 ...................................................................................61
S4 ...................................................................................61
S5 ...................................................................................61
S6 ...................................................................................61
S7 ...................................................................................61
S8 ...................................................................................61
Safe Disable Circuit ............................................................ 501
Safe Disable Function Wiring Example (SINK Mode).................... 502
Safe Disable Input Function................................................... 501
Safe Disable Inputs ...............................................................61
Safe Disable Monitor Output Function and Digital Operator Display
..................................................................................... 503
Safe Disable Signal Input...................................................... 319
Safety Hazard Definitions .......................................................18
Safety Information................................................................18
Safety Input and EDM Terminal Status ..................................... 503
Safety Monitor Output ...........................................................62
Safety Standard ................................................................. 375
SC ...................................................................................61
S-Curve Characteristics .................................................. 156, 294
SE ................................................................................. 322
Search Operation Voltage Limit .............................................. 153
Self-diagnosing function of the serial communication interface circuits
..................................................................................... 494
SEr ................................................................................ 313
Serial Communications Cable Connection Terminals (TB5) ............. 466
Serial Communication Terminals...............................................63
Serial Communication Transmission Error ................................. 316
Serviceable Parts................................................................ 356
Setup Group .......................................................................84
Setup Group Parameters .........................................................89
Setup Mode ........................................................................85
Shielded Twisted-Pair Cables ...................................................66
Short Circuit Brake Time at Start............................................. 135
Short Circuit Brake Time at Stop............................................. 135
Short Circuit Braking Current................................................. 135
Side-by-Side Installation.........................................................41
Side-by-Side Mounting ........................................................ 377
Side-by-Side Setup ...............................................................41
Simple Motor Setup Using V/f Control........................................93
Simplified Setup Using the Setup Group ......................................85
Single Drive KEB Ride-Thru 1 ............................................... 244
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual