YASKAWA AC Drive-A1000 Technical Manual page 525

Motor Overload Protection Selection ............................ 225, 427, 499
Motor Overload Protection Time ................................. 240, 427, 500
Motor Parameters ............................................................... 184
Motor Performance Fine-Tuning ............................................. 290
Motor Poles...................................................................... 105
Motor Produces Insufficient Torque ......................................... 342
Motor Protection ................................................................ 238
Motor Protection Using a Positive Temperature Coefficient ............. 233
Motor PTC Characteristics .................................................... 242
Motor Pull Out or Step Out Detection ....................................... 313
Motor q-Axis Current at Previous Fault ..................................... 451
Motor q-Axis Inductance ...................................................... 194
Motor Rated Current ............................. 105, 107, 187, 194, 444, 499
Motor Rated Power ........................................... 107, 189, 193, 444
Motor Rated Slip.......................................................... 108, 187
Motor Rated Voltage ............................................... 105, 107, 444
Motor Rotates After the Drive Output is Shut Off ......................... 342
Motor Rotates Faster Than the Frequency Reference...................... 340
Motor Rotates in One Direction Only........................................ 338
Motor Secondary Current (Iq) ................................................ 454
Motor Selection ................................................................. 212
Motor Selection 1/2............................................................. 444
Motor Speed ..................................................................... 448
Motor Speed at Previous Fault ................................................ 450
Motor Speed Error 2............................................................ 330
Motor Speed Fault .............................................................. 330
Motor Stalls During Acceleration or With Large Loads .................. 339
Motor Stator Resistance........................................................ 194
Motor Switch during Run...................................................... 322
Motor Temperature Input Filter Time.................................. 242, 427
Motor Wiring......................................................................59
Mounting hole.....................................................................35
MP ..................................................................................62
Multi-Function Analog Inputs ................................................ 178
Multi-Function Analog Input Selection Error............................... 325
Multi-Function Analog Input Terminal Settings ........................... 228
Multi-Function Analog Outputs .............................................. 161
Multi-Function Analog Output Terminal AM Bias ........................ 234
Multi-Function Analog Output Terminal AM Gain........................ 234
Multi-Function Analog Output Terminal AM Monitor Selection........ 234
Multi-Function Analog Output Terminal AM Signal Level Selection
..................................................................................... 235
Multi-Function Analog Output Terminal FM Bias......................... 234
Multi-Function Analog Output Terminal FM Gain ........................ 234
Multi-Function Analog Output Terminal FM Monitor Selection ........ 234
Multi-Function Analog Output Terminal FM Signal Level Selection
..................................................................................... 235
Multi-Function Digital Inputs .............................................61, 207
Multi-Function Digital Input Terminal Settings ............................ 207
Multi-Function Digital Output ..................................................62
Multi-Function Digital Outputs ............................................... 218
Multi-Function Digital Output Terminal Settings .......................... 218
Multi-Function Input Selection Error ........................................ 324
Multiple Drive Installation ......................................................41
Multiple Drive Wiring ...........................................................60
Multi-Step Speed Selection.................................................... 127
L1-01 ............................................................................ 499
N
n1-02.............................................................................. 290
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual
n2-01.............................................................................. 291
n2-02........................................................................ 291, 326
n2-03........................................................................ 291, 326
Nameplate..........................................................................32
ND ................................................................................ 166
ndAT.............................................................................. 333
NetRef/ComRef Function Selection.......................................... 202
Network Termination .......................................................... 466
Noise From the Drive or Output Lines When the Drive is Powered On
..................................................................................... 341
No-Load Current Alarm ....................................................... 328
No-Load Current Error......................................................... 329
No-Load Operation ............................................................. 112
No-Load Operation Test Run ................................................. 112
Normal Duty..................................................................... 166
Normal Duty Ratings........................................................... 166
Notes on Inertia Tuning and ASR Gain Auto-Tuning ..................... 104
Notes on Rotational Auto-Tuning ............................................ 103
Notes on Stationary Auto-Tuning ............................................ 103
Number of Auto Restart Attempts...................................... 258, 431
Number of Motor Poles ...................................... 107, 188, 194, 444
Number of PM Motor Poles ................................................... 109
Number of Run Commands ................................................... 452
Number of Run Commands Counter Initialization......................... 283
Number of Speed Search Restarts ............................................ 140
O
o2-01.............................................................................. 337
o2-03.............................................................................. 115
o2-04.................................................................. 290, 320, 324
o4-03.............................................................................. 320
oC ................................................................................. 306
oFA00 ............................................................................ 307
oFA01 ............................................................................ 307
oFA03 to oFA06 ................................................................ 307
oFA10 ............................................................................ 307
oFA11 ............................................................................ 307
oFA12 to oFA17 ................................................................ 307
oFA30 to oFA43 ................................................................ 307
oFb00 ............................................................................. 307
oFb01 ............................................................................. 307
oFb02 ............................................................................. 307
oFb03 to oFb11 ................................................................. 307
oFb12 to oFb17 ................................................................. 307
oFb30 to oFb43 ................................................................. 307
oFC00 ............................................................................ 308
oFC01 ............................................................................ 308
oFC02 ............................................................................ 308
oFC03 to oFC11 ................................................................ 308
oFC12 to oFC17 ................................................................ 308
oFC30 to oFC43 ................................................................ 308
Offset Frequency.......................................................... 183, 455
oH ........................................................................... 308, 320
oH1 ............................................................................... 308
oH2 ............................................................................... 320
oH3 ......................................................................... 309, 320
oH4 ............................................................................... 309
oL1................................................................................ 309
oL2.......................................................................... 310, 342
oL2 Characteristics Selection at Low Speeds......................... 265, 434
Index
525