YASKAWA AC Drive-A1000 Technical Manual page 105

6. The display automatically returns to the display shown in Step 3.
<1> T1-00 will appear on the display when one of the multi-function inputs has been set to switch between motor 1 and motor 2 (H1-oo = 16).
n Enter Data from the Motor Nameplate
After selecting the type of Auto-Tuning, enter the data required from the motor nameplate.
Note: These instructions continue from Step 6 in "Selecting the Type of Auto-Tuning".
1.
Press to access the motor output power parameter T1-02.
2.
Press to view the default setting.
F2
F1
3.
Press , ,
right
left
kW.
4.
Press to save the setting.
5. The display automatically returns to the display in Step 1.
Repeat Steps 1 through 5 to set the following parameters:
• T1-03, Motor Rated Voltage
• T1-04, Motor Rated Current
• T1-05, Motor Base Frequency
6.
• T1-06, Number of Motor Poles
• T1-07, Motor Base Frequency
• T1-09, Motor No-Load Current (Stationary Auto-Tuning 1 or 2 only)
• T1-10, Motor Rated Slip (Stationary Auto-Tuning 2 only)
Note: 1. For details on each setting,
2. To execute Stationary Auto-Tuning for line-to-line resistance only, set parameters T1-02 and T1-04.
n Starting Auto-Tuning
WARNING! Sudden Movement Hazard. The drive and motor may start unexpectedly during Auto-Tuning, which could result in death or
serious injury. Ensure the area surrounding the drive motor and load are clear before proceeding with Auto-Tuning.
WARNING! Electrical Shock Hazard. High voltage will be supplied to the motor when Stationary Auto-Tuning is performed even with the
motor stopped, which could result in death or serious injury. Do not touch the motor until Auto-Tuning has been completed.
NOTICE: Rotational Auto-Tuning will not function properly if a holding brake is engaged on the load. Failure to comply could result in improper
operation of the drive. Ensure the motor can freely spin before beginning Auto-Tuning.
Enter the required information from the motor nameplate. Press
Note: These instructions continue from Step 6 in "Enter Data from the Motor Nameplate".
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual
Step
Step
, , and to enter the motor power nameplate data in
Refer to Parameter Settings during Induction Motor Auto-Tuning: T1 on page
to proceed to the Auto-Tuning start display.
4.7 Auto-Tuning
Display/Result
- A.TUNE - PRG Rdy
Tuning Mode Sel
T1-01= 0
*0*
Standard Tuning
ESC FWD DATA
Display/Result
- A.TUNE - PRG Rdy
Mtr Rated Power
T1-02= 0.75kW
(0 00 ~ 650 00)
"0.75kW"
ESC FWD DATA
- A.TUNE - PRG Rdy
Mtr Rated Power
T1-02= 000.75kW
(0 00 ~ 650 00)
"0.75kW"
FWD
- A.TUNE - PRG Rdy
Mtr Rated Power
T1-02= 000.40kW
(0 00 ~ 650 00)
"0.75kW"
FWD
Entry Accepted
- A.TUNE - PRG Rdy
Mtr Rated Power
T1-02= 0.40kW
(0 00 ~ 650 00)
"0.75kW"
ESC FWD DATA
- A.TUNE - PRG
Rated Voltage
T1-03= 200 0VAC
(0 0 ~ 255.0)
"200.0VAC"
ESC FWD DATA
- A.TUNE - PRG
Mtr Rated Slip
T1-10= X.XX Hz
(0 00 ~ 20.00)
"X XX Hz"
ESC FWD DATA
106.
105
4