YASKAWA AC Drive-A1000 Technical Manual page 529

Single Drive KEB Ride-Thru 2 ............................................... 244
Sink/source jumper S3 ...........................................................36
Sinking/Sourcing Mode Switch for Digital Inputs ...........................36
Slave Address ................................................................... 473
Slip Compensation.............................................................. 156
Slip Compensation Gain ................................................. 156, 291
Slip Compensation Limit ...................................................... 157
Slip Compensation Primary Delay Time .............................. 157, 291
Slip Compensation Selection during Regeneration ........................ 157
SN...................................................................................61
Soft Charge Bypass Relay Maintenance..................................... 452
Soft Charge Bypass Relay Maintenance Time.............................. 320
Soft CLA Selection ............................................................. 434
Soft Starter Speed Reference at Previous Fault............................. 451
Software Current Limit Selection ............................................ 266
Software No. (Flash) ........................................................... 450
Software No. (ROM) ........................................................... 450
Software version ..................................................................32
Space Between Drives (Side-by-Side Mounting) ............................41
Speed/Torque Control Switchover Time .................................... 182
Speed Agree 1 Time Chart .................................................... 220
Speed Agree 2 Time Chart .................................................... 223
Speed Agreement Detection Level ..................................... 256, 430
Speed Agreement Detection Level (+/-) ............................... 256, 430
Speed Agreement Detection Selection....................................... 257
Speed Agreement Detection Width .................................... 256, 430
Speed Agreement Detection Width (+/-) .............................. 256, 430
Speed Control Accuracy ....................................................... 374
Speed Control Integral Time 1 ................................................ 321
Speed Control Loop Auto-Tuning............................................ 102
Speed Control Proportional Gain 1........................................... 321
Speed Control Range ........................................................... 374
Speed Deviation (for Control Mode with PG) .............................. 302
Speed Deviation (when using a PG option card) ........................... 317
Speed Estimation Type Speed Search........................................ 137
Speed Feedback Detection Contol (AFR) Tuning.......................... 270
Speed Feedback Detection Control (AFR) Gain ..................... 270, 436
Speed Feedback Detection Control (AFR) Time Constant 1 ....... 270, 436
Speed Feedback Detection Control (AFR) Time Constant 2 ....... 270, 436
Speed Feedback Detection Control Gain .............................. 275, 438
Speed Feedback Detection Control Gain during ov Suppression ........ 277
Speed Limit...................................................................... 182
Speed Limitation................................................................ 180
Speed Limit Bias.......................................................... 180, 182
Speed Limit Selection .......................................................... 181
Speed Response ................................................................. 374
Speed Search .................................................................... 128
Speed Search Deactivation Current .......................................... 139
Speed Search Deceleration Time ............................................. 139
Speed Search Delay Time ..................................................... 139
Speed Search Detection Compensation Gain ............................... 139
Speed Search Method Selection .............................................. 140
Speed Search Restart Current Level.......................................... 140
Speed Search Restart Detection Time........................................ 140
Speed Search Selection at Start ............................................... 138
Speed Search Wait Time....................................................... 140
Stall Prevention ........................................................... 250, 294
Stall Prevention Detection Time.............................................. 256
Stall Prevention Level during Acceleration ........................... 251, 429
Stall Prevention Level during Run ..................................... 253, 429
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual
Stall Prevention Limit during Acceleration ........................... 250, 429
Stall Prevention Selection during Acceleration....................... 250, 429
Stall Prevention Selection during Deceleration....................... 252, 429
Stall Prevention Selection during Run ................................. 253, 429
Standard Connection Diagram ..................................................50
Starting Torque.................................................................. 374
Start-Up Flowcharts ..............................................................91
Stationary Auto-Tuning........................................................ 103
Stationary Auto-Tuning 1...................................................... 100
Stationary Auto-Tuning 2...................................................... 100
Stationary Auto-Tuning for Line-to-Line Resistance ...................... 100
Stator Resistance Error......................................................... 331
Status Display .....................................................................96
STo ............................................................................... 313
STOP button Input.............................................................. 329
STOP Key .........................................................................79
STOP Key Function Selection .......................................... 280, 440
Stopping Method after Communication Error .............................. 468
Stopping Method Selection.................................................... 128
Storage Temperature .............................................................40
SvE ............................................................................... 314
Swing PWM ............................................................... 167, 372
Switching Between LOCAL and REMOTE ..................................89
Switching Between Torque and Speed Control............................. 180
System KEB Ride-Thru 1 ..................................................... 244
System KEB Ride-Thru 2 ..................................................... 244
T
T/L3.................................................................................58
T1-02 ............................................................................. 329
T1-03 ....................................................................... 105, 328
T1-04 ................................................................. 105, 328, 329
T1-05 ....................................................................... 105, 328
T1-06 ............................................................................. 105
T1-07 ....................................................................... 105, 106
Target DC Bus Voltage for Overvoltage Suppression and Stall Prevention
..................................................................................... 254
Task Complete .................................................................. 332
Temperature Derating ............................................................41
Terminal A1 Bias Setting...................................................... 228
Terminal A1 Function Selection.............................................. 228
Terminal A1 Gain Setting ..................................................... 228
Terminal A1 Signal Level Selection ......................................... 228
Terminal A2 Bias Setting...................................................... 230
Terminal A2 Function Selection.............................................. 230
Terminal A2 Gain Setting ..................................................... 230
Terminal A2 Signal Level Selection ......................................... 230
Terminal A3 Bias Setting...................................................... 230
Terminal A3 Function Selection.............................................. 229
Terminal A3 Gain Setting ..................................................... 230
Terminal A3 Signal Level Selection ......................................... 229
Terminal Block Configuration ..................................................54
Terminal Board ........................................................ 35, 36, 356
Terminal Board Connection Error............................................ 301
Terminal Board Connector ......................................................36
Terminal Connections for Communication Self-Diagnostics............. 494
Terminal Cover .............................................................. 35, 55
Terminal Cover Screw ...........................................................35
Terminal M1-M2 Function Selection ........................................ 218
Terminal M1-M2 Output Selection .......................................... 201
Index
529