Huawei Quidway S9300 Configuration Manual - Multicast page 235

Quidway S9300 Terabit Routing Switch
Configuration Guide - Multicast
Step 2 Enable multicast and configure PIM-SM.
# Enable multicast on all S9300s, and PIM-SM on all interfaces. Enable the IGMP function on
the interfaces at the host side. The configurations of other S9300s are similar to configuration
of S9300-C, and are not mentioned here.
[S9300-C] multicast routing-enable
[S9300-C] interface vlanif 104
[S9300-C-Vlanif104] igmp enable
[S9300-C-Vlanif104] pim sm
[S9300-C-Vlanif104] quit
[S9300-C] interface vlanif 101
[S9300-C-Vlanif102] pim sm
[S9300-C-Vlanif102] quit
[S9300-C] interface vlanif 100
[S9300-C-Vlanif100] pim sm
[S9300-C-Vlanif100] quit
Step 3 Configure Loopback1, Loopback10, C-BSR, and C-RP.
# Configure the same address for Loopback1 and Loopback10 on both S9300-C and S9300-D.
Configure C-BSR on Loopback1 and C-RP on Loopback 10. The configuration of S9300-D is
similar to configuration of S9300-C, and is not mentioned here.
[S9300-C] interface loopback 1
[S9300-C-LoopBack1] ip address 3.3.3.3 255.255.255.255
[S9300-C-LoopBack1] pim sm
[S9300-C-LoopBack1] quit
[S9300-C] interface loopback 10
[S9300-C-LoopBack10] ip address 10.1.1.1 255.255.255.255
[S9300-C-LoopBack10] pim sm
[S9300-C-LoopBack10] quit
[S9300-C] pim
[S9300-C-pim] c-bsr loopback 1
[S9300-C-pim] c-rp loopback 10
[S9300-C-pim] quit
Step 4 Configure Loopback0 interfaces and MSDP peers.
# Configure the MSDP peer on Loopback0 of S9300-C.
[S9300-C] interface loopback 0
[S9300-C-LoopBack0] ip address 1.1.1.1 255.255.255.255
[S9300-C-LoopBack0] pim sm
[S9300-C-LoopBack0] quit
[S9300-C] msdp
[S9300-C-msdp] originating-rp loopback0
[S9300-C-msdp] peer 2.2.2.2 connect-interface loopback0
[S9300-C-msdp] quit
# Configure the MSDP peer on Loopback0 of S9300-D.
[S9300-D] interface loopback 0
[S9300-D-LoopBack0] ip address 2.2.2.2 255.255.255.255
[S9300-D-LoopBack0] pim sm
[S9300-D-LoopBack0] quit
[S9300-D] msdp
[S9300-D-msdp] originating-rp loopback0
[S9300-D-msdp] peer 1.1.1.1 connect-interface loopback0
[S9300-D-msdp] quit
Step 5 Verify the configuration.
# Run the display msdp brief command to view the status of the MSDP peer relation between
S9300s. Information about MSDP peers on S9300-C and S9300-D is as follows:
<S9300-C> display msdp brief
MSDP Peer Brief Information of VPN-Instance: public net
Issue 01 (2009-07-28) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5 MSDP Configuration
5-43