Huawei Quidway S9300 Configuration Manual - Multicast page 228

5 MSDP Configuration
1.
2.
3.
4.
Data Preparation
To complete the configuration, you need the following data:
l
l
l
l
l
l
l
l
Procedure
Step 1 Configure the IP addresses of interfaces and the unicast routing protocol
# According to
Configure OSPF in the AS. Configure EBGP between S9300-A and S9300-F, and between
S9300-B and S9300-E. Import BGP and OSPF routes into each other's routing table. Ensure that
the S9300s can communicate with each other through the network layer. Ensure the dynamic
route update between routers through the unicast routing protocol. The configuration procedure
is not mentioned.
Step 2 Enable multicast on all S9300s and PIM-SM on all interfaces, and enable the IGMP function on
the interfaces connected to the hosts. In addition, configure the service boundary of BSR on the
interfaces of S9300s on the AS boundary.
# Enable multicast all the S9300s and enable PIM-SM on each interface. The configurations of
other S9300s are similar to configuration of S9300-C, and are not mentioned here.
[S9300-C] multicast routing-enable
[S9300-C] interface vlanif 100
[S9300-C-Vlanif100] pim sm
[S9300-C-Vlanif100] quit
[S9300-C] interface vlanif 400
5-36
Configure IP addresses for the interfaces on each S9300, configure OSPF in the AS,
configure EBGP between ASs, and import BGP and OSPF routes into each other's routing
table.
Enable multicast on all S9300s and PIM-SM on all interfaces and enable IGMP on the
interfaces at the user side. Configure Loopback0, C-BSR, and C-RP. The Loopback 0
interfaces on S9300-C, S9300-D, and S9300-F function as the C-BSR and the C-RP of each
PIM-SM domain.
Establish MSDP peer relation between RPs of each domain. Establish the MSDP peer
relation between S9300-C and S9300-D and establish the MSDP peer relation between
S9300-C and S9300-F.
Specify a static RPF peer for the MSDP peer. The static RPF peers of S9300-C are S9300-
D and S9300-F. S9300-D and S9300-F have only one static RPF peer, namely, S9300-C.
According to RPF rules, S9300s receive SA messages from static RPF peers.
Number of the AS that S9300-A, S9300-B, and S9300-C belong to: 100
Router IDs of S9300-A, S9300-B, and S9300-C: 1.1.1.3, 1.1.1.2 and 1.1.1.1
Number of the AS that S9300-D and S9300-E belong to: 200
Router IDs of S9300-D and S9300-E: 2.2.2.2 and 2.2.2.1
Number of the AS that S9300-F and S9300-G belong to: 200
Router ID of S9300-F: 3.3.3.3
S9300-C uses the list-df policy to filter the SA messages from S9300-D and S9300-F.
S9300-D and S9300-F use the list-c policy to filter the SA messages from S9300-C.
NOTE
This configuration example describes only the commands used to configure static RPF peers.
Figure 5-2, configure IP addresses and masks for the interfaces of each S9300.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Quidway S9300 Terabit Routing Switch
Configuration Guide - Multicast
Issue 01 (2009-07-28)