Keithley 2601 Reference Manual page 558

Index
Commands
Considerations
Limitations
Low limits
Manual ..............................................6-3
Programming
Programming example
Reading buffers
Readings
Maximum
Recalling
Requesting
Storing ..............................................7-3
Rear panel summaries
Recalling readings
Recommended test equipment
Recommended verification equipment
Registers
Enable and transition
Measurement event
Operation event
Programming example
Questionable event
Reading
Serial polling and SRQ
Service request enable
Standard event
Status sets
System summary event
Rel ............................................................6-8
Defining a value
Enabling and disabling
Front panel
Remote programming
REM .......................................................11-7
Remote calibration
Remote operation
Source-measure procedure
Remote programming
Ohms ..............................................4-15
Power ...................................4-16
Remote TSP-Link synchroniaztion
line commands
Removing Stale Buffers
REN (remote enable)
Restoring factory defaults
Rise time ................................................8-22
Rotary knob ..............................................1-8
RS-232 cable
RS-232 Interface
Terminator
RS-232 interface
Baud rate
Connections
Data bits
Flow control
Operation
Parity ............................................11-10
Sending and receiving data
Run-time environment
Memory considerations
I-4
.......................................6-4
.................................6-4
........................................6-3
..........................................6-3
....................................6-4
.....................6-5
......................................12-5
..........................................6-3
...........................................7-3
,
...........................1-24 4-10
.............................1-9
....................................7-3
..............15-3
...15-3
..................... D-13
....................... D-24
............................. D-18
.................. D-27
....................... D-21
......................................... D-10
.................. D-12
.................. D-12
.............................. D-16
..................................... D-15
................. D-15
................................6-8
.....................6-8
.......................................6-8
.......................6-9
.................................16-5
..............4-9
.............................1-24
,
4-18
.....................................10-10
..........................9-12
.............................11-6
.......................15-4
............................................1-5
......................................11-9
........................................11-9
.................................11-11
.......................................11-10
..................................11-10
........................................11-8
............11-9
,
......................2-3 2-7
..................2-44
Series 2600 System SourceMeter® Instruments Reference Manual
S
Safety shield
Safety symbols and terms
Script management
Scripting ................................................... 2-3
Scripting Language
Scripts .............................................. 2-4
Creating
Creating functions
Factory scripts
Importing
Launch configuration
Launching
Modifying
Programming model
Retrieving from Model 260x
Saving
User ............................................... 2-34
Scripts, named
SDC (selective device clear)
Selecting an interface
Sensing .................................................... 3-5
2-wire local
4-wire remote
Mode selection
Ohms ............................................. 4-13
Serial polling
Setting the measurement range
Setting the source range and
output value
Settling time considerations
Setups
Front panel
Power-on
Restoring
User ............................................... 1-21
Shielding
Noise .............................................. 3-13
Safety ............................................. 3-16
Sink .......................................................... 8-7
Sink operation
SMU connections
Source ...................................................... 8-7
Source I measure I
Source V measure V
Source-measure capabilities
Source-measure procedure
Front panel operation
Programming example
Remote operation
SPE, SPD (serial polling)
Specifications
Speed ....................................................... 6-6
Command
Configuration menu
Programming example
Remote programming
Setting
SRQ (Service Request)
Staircase sweeps
Standard libraries
Status byte and service request (SRQ)
Status byte and service request
commands .............................................D-12
.......................................... 3-16
........................ 1-3
................................ 2-40
.................................. 2-3
,
2-6
......................................... 2-15
............................ 2-5
................................ 2-42
........................................ 2-24
...................... 2-19
...................................... 2-22
........................................ 2-15
......................... 2-9
........... 2-23
............................................ 2-16
......................................... 2-4
.................. 11-7
............................ 11-2
....................................... 3-6
................................... 3-7
................................. 3-8
..........................................D-12
............. 15-6
........................................... 15-5
................... 8-23
..................................... 1-21
........................................ 1-22
........................................ 1-21
........................................ 4-12
................................... 3-10
................................. 8-16
.............................. 8-16
.................... 4-2
....................... 4-8
................... 4-10
............................ 4-9
....................... 11-7
...........................................A-1
........................................ 6-7
.......................... 6-7
..................... 6-7
...................... 6-7
.............................................. 6-7
,
.............. 11-8 D-10
..................................... 8-3
................................... 2-53
.D-10
2600S-901-01 Rev. C / January 2008