WARRANTY Keithley Instruments, Inc. warrants this product to be free from defects in material and workmanship for a period of one (1) year from date of shipment. Keithley Instruments, Inc. warrants the following items for 90 days from the date of shipment: probes, cables, software, rechargeable batteries, diskettes, and documentation.
Keithley Instruments products are designed for use with electrical signals that are rated Measurement Category I and Measurement Category II, as described in the International Electrotechnical Commission (IEC) Standard IEC 60664. Most measurement, control, and data I/O signals are Measurement Category I and must not be directly connected to mains voltage or to voltage sources with high transient over-voltages.
Page 6
To maintain protection from electric shock and fire, replacement components in mains circuits - including the power transformer, test leads, and input jacks - must be purchased from Keithley Instruments. Standard fuses with applicable national safety approvals may be used if the rating and type are the same.
Series 2600A SourceMeter® Instruments Quick Start Guide SMU Connectors 2601A/2611A/2602A/2612A (diagram shown for 2602A/2612A) Model 2635A/2636A 1 - CHANNEL A and CHANNEL B 1 - CHANNEL A and CHANNEL B Triax connectors 2 - DIGITAL I/O 2 - DIGITAL I/O...
Page 8
Series 2600A SourceMeter® Instruments Quick Start Guide Model 2602A/2612A two-wire connections (local sensing) Four-wire Connections Model 2636A four-wire connections (remote sensing) Model 2602A/2612A four-wire connections (remote sensing) 2600AS-903-01 Rev. A / September 2008...
Series 2600A SourceMeter® Instruments Quick Start Guide How do I make front panel measurements? (this example assumes 10kOhm resistor as a DUT- but you may use any 2 terminal DUT with appropriate source values) Step 1: Connect the DUT Connect a 10kO resistor to the SourceMeter Channel A HI and LO terminals. Step 2: Select source and set source level Perform the following steps to select the voltage source and set the source value to 10V: Press Channel A SRC to select the V-Source (indicated by the "V"...
Page 10
Series 2600A SourceMeter® Instruments Quick Start Guide The command window is displayed. At the command prompt, type ipconfig/all. Enter. When the information is displayed, record the DHCP mode, IP address, subnet mask, default gateway, and DNS servers. Record the existing IP configuration information in the table below so that you can properly return all settings back to their original configuration before reconnecting your PC to a corporate network DHCP Enabled...
Page 11
Series 2600A SourceMeter® Instruments Quick Start Guide The Internet Protocol (TCP/IP) Properties dialog box Set the IP Address DECISION: Is the IP address and subnet mask field populated? Yes: If populated, record this address and subnet mask to use in "Configure the instrument's LAN settings" section. NO: blank, enter the IP address of 192.168.0.3 and subnet mask of 255.255.255.0 in the field to use in "Configure the instrument's LAN settings"...
Series 2600A SourceMeter® Instruments Quick Start Guide Change the subnet mask from within the LAN MENU. Select CONFIG > SUBNETMASK, then ENTER (hint: SUBNETMASK is to the right of GATEWAY). Modify the SUBNETMASK to be the same as PC settings recorded above or 255.255.255.000 if DHCP Enabled = yes. Push the wheel or press the ENTER key when finished changing all the characters.
Page 13
As an example, let’s say you want to generate an idvd curves of a FET. Step 2. Connect the DUT Here the device connection with a 2602A is shown. Step 3. Configure the project and Run From the Quick Start Menu, select multi-SMU sweep Click SMU assignment.
Page 14
Series 2600A SourceMeter® Instruments Quick Start Guide Assign the SMUs (smua for voltage step on Gate and smub for voltage sweep on Drain) Set Step and Sweep Parameters Click Run Step 4. View the data Data can be viewed in tabular format, plotted or exported to a .csv file. 2600AS-903-01 Rev.
Page 16
M E A S U R E C O N F I D E N C E Keithley Instruments, Inc. Corporate Headquarters • 28775 Aurora Road • Cleveland, Ohio 44139 • 440-248-0400 • Fax: 440-248-6168 • 1-888-KEITHLEY • www.keithley.com 12/06...
Need help?
Do you have a question about the 2602A and is the answer not in the manual?
Questions and answers