Display Mode; Display Mode - Selection Of Read-Outs - Danfoss FC 300 Design Manual

FC 300 Design Guide

Display Mode

"
In normal operation, up to 5 different operating variables can be indicated continuously in
the middle section: 1.1, 1.2, and 1.3 as well as 2 and 3.

Display Mode - Selection of Read-Outs

"
You can toggle between three status readout
screens by pressing the [Status] key.
Operating variables with different formatting are
shown in each status screen - see below.
The table shows the measurements you can link to
each of the operating variables. Define the links
via par. 0-20, 0-21, 0-22, 0-23, and 0-24.
Each readout parameter selected in par. 0-20
to par. 0-24 has its own scale and digits after
a possible decimal point. By larger numeric
value of a parameter fewer digits are displayed
after the decimal point.
Ex.: Current readout
5.25 A; 15.2 A 105 A.
Status screen I:
This readout state is standard after start-up
or initialization.
Use [INFO] to obtain information about the
measurement links to the displayed operating
variables /1.1, 1.2, 1.3, 2, and 3).
See the operating variables shown in the
screen in this illustration.
140
How to Program
MG.33.B6.22 - VLT is a registered Danfoss trademark
Operating variable:
Par. 16-00 Control Word
Par. 16-01 Reference
Par. 16-02 Reference
Par. 16-03 Status word
Par. 16-04 Alarm word
Par. 16-05 Warning word
Par. 16-06 Extended status wordhex
Par. 16-10 Power
Par. 16-11 Power
Par. 16-12 Motor voltage
Par. 16-13 Frequency
Par. 16-14 Motor current
Par. 16-16 Torque
Par. 16-17 Speed
Par. 16-18 Motor thermal
Par. 16-20 Phase angle
Par. 16-30 DC link voltage
Par. 16-32 Brake energy / s
Par. 16-33 Brake energy / 2 min
Par. 16-34 Heatsink temp.
Par. 16-35 Inverter thermal
Par. 16-36 InomVLT
Par. 16-37 ImaxVLT
Par. 16-38 SL controller state
Par. 16-39 Control card temp.
Par. 16-50 External reference
Par. 16-51 Pulse reference
Par. 16-52 Feedback
Par. 16-60 Digital input
Par. 16-61 Terminal 53 switch setting
Par. 16-62 Analog input 53
Par. 16-63 Terminal 54 switch setting
Par. 16-64 Analog input 54
Par. 16-65 Analog output 42
Par. 16-66 Digital output
Par. 16-67 Freq. input #29
Par. 16-68 Freq. input #33
Par. 16-69 Pulse output #27
Par. 16-70 Pulse output #29
Par. 16-80 Fieldbus CTW
Par. 16-82 Fieldbus REF
Par. 16-83 Fieldbus MAV
Par. 16-84 Comm. option STW
Par. 16-85 FC port CTW 1
Par. 16-86 FC port REF 1
1.1
1.2
2
3
1.3
Unit:
hex
[unit]
%
hex
hex
hex
[%]
[kW]
[HP]
[V]
[Hz]
[A]
Nm
[RPM]
%
V
kW
kW
C
%
A
A
C
[Unit]
bin
V
V
[mA]
[bin]
[Hz]
[Hz]
[Hz]
[Hz]
hex
hex
hex
hex
hex
hex