Making Preparations - Canon imageRUNNER 7095 Service Manual

18.2 Making Preparations

18.2.1 Installing the System Software
(System CD -> SST)
Here, you will be copying the system software
found on the System CD to the SST.
[Preparatory Work]
Requirements
- PC to which the SST (version 3.21 or later) has
been installed
- System CD
[Installing the System Software]
1) Turn on the PC.
2) Set the System CD in the PC.
3) Start up the SST.
4) Click [Register Firmware].
Service Support Tool DLM0 (Ver.3.21E)
Target Selection CONTROL
S e l e c t t h e t a r g e t . C l i c k a b u t t o n t o exe c u t e .
MFP
MFP
R e g i s t e r F i r m wa r e
USB
D e l e t e F i r m wa r e
D e l e t e B a ck u p D a t a
USB S y s t e m M a n a g e m e n t
c:
F-18-4
5) Select the drive in which the System CD has
been set, and click [SEARCH].
Service Support Tool DLM0 (Ver.3.21E)
Registerd Firms CONTROL
C l i c k a b u t t o n t o exe c u t e .
Registered fir mware
R e g i s t e r F i r m wa r e
D e l e t e F i r m wa r e
D e l e t e B a ck u p D a t a
S y s t e m M a n a g e m e n t
F-18-5
Model List
S e l e c t a m o d e l t o c o n n e c t
CONNECT
START
CANCEL
EXIT
Regist Firm
S e l e c t a d r i ve a n d fo l d e r.
CONNECT
e:
e:
iR7105C-XXxx-BOOT
iR7105-USen
iR7105-XXen0107-RUI
iR7105XXen0111-TTS
iR7105-XXen-LANG
iR7105-XXxx0100-BROWS
REGISTER
SEARCH
CANCEL
EXIT
6) A list of system software found on the System
CD appears. Remove the check marks from the
folders and software files you do not need, and
click [REGISTER].
0011-6751
Service Support Tool DLM0 (Ver.3.21E)
Registerd Firms
Registered fir mware
7) When a message has appeared to indicate that
the system software has been installed, click
[OK].
Service Support Tool DLM0 (Ver.3.21E)
Registerd Firms
Registered fir mware
TTS
XXenv0111
iRCXXXX
HDFormat
XXxxv0002
KEY
XXxcv0101
XXxpv0101
SDICT
18.2.2 Copying the System Software (SST -
> USB)
Here, you will be copying the system software
from the SST to a USB device.
[Preparatory Work]
Requirements
- PC to which the SST (version 3.21 or later) has
been installed
- USB device *
*: USB Requirements
Interface USB 1.1 or higher (USB 2.0
recommended)
Capacity 1 GB or more recommended (A set of
system software is in excess of 512 MB.)
Format FAT (FAT16), FAT32 (It must not be
NTFS or HFS.)
single partition (There must not be
multiple partitions.)
CONTROL Found Firm
C l i c k a b u t t o n t o exe c u t e .
T h e f i r m wa r e l i s t e d b e l ow i s fo u n d .
U n c h e cke d f i r m wa r e i s r e g i s t e r e d .
iR7105
CONNECT
SYSTEM
LANGUAGE
R e g i s t e r F i r m wa r e
RUI
D e l e t e F i r m wa r e
MEAPCONT
BOOT
D e l e t e B a ck u p D a t a
BROWSER
S y s t e m M a n a g e m e n t
REGISTER
CANCEL
EXIT
F-18-6
CONTROL Found Firm
C l i c k a b u t t o n t o exe c u t e .
F i r m wa r e r e g i s t ra t i o n c o m p l e t e d .
> > > B a t c h R e g i s t ra t i o n R e s u l t s
iR7105
CONNECT
SYSTEM
LANGUAGE
R e g i s t e r F i r m wa r e
RUI
D e l e t e F i r m wa r e
MEAPCONT
BOOT
D e l e t e B a ck u p D a t a
BROWSER
S y s t e m M a n a g e m e n t
G3FAX
DCON
O K
TTS
iRYYYY
CANCEL
HDFormat
KEY
EXIT
F-18-7
Chapter 18
USenv0112
XXenv0112
XXenv0107
XXxxv0105
XXxxv0103
XXxxv0100
USenv0112 >>> With no
XXenv0112 >>> Regist
XXenv0107 >>> Regist
XXxxv0105 >>> Regist
XXxxv0103 >>> Regist
XXxxv0100 >>> Regist
XXxxv6102 >>> Regist
XXxxv0102 >>> Regist
XXxxv0111 >>> Regist
XXxxv0002 >>> Regist
XXenv0111 OK!
0011-6752
18-5