Canon imageRUNNER 7095 Service Manual page 453

Code Sensor type
0008 delivery stationary 1 PI13,S9
0009 delivery stationary 2 PI13,S9
0010 pre-reversal delay 1 S3
0011 pre-reversal delay 2 S1,S3
0012 pre-reversal delay 3 PI4
0013 pre-reversal
stationary 1
0014 pre-reversal
stationary 2
0015 pre-reversal
stationary 3
0016 pre-reversal
stationary 4
0017 pre-reversal pickup
delay
0018 pre-reversal pickup
stationary 1
0019 pre-reversal pickup
stationary 2
0020 reversal pickup
delay
0021 reversal pickup
stationary
0022 pickup lead edge
skew
0023 pickup trail edge
skew
0024 pickup fault 1
Sensor No. Description
At time of delivery, the manual feeder registration roller sensor detects
the original after it has been moved a specific distance (original length +
100 mm) following the activation of the delivery sensor.
At time of delivery, the delivery sensor detects the original after it has
been moved a specific distance (original length + 100 mm) following the
deactivation of the manual feeder registration roller sensor.
At time of pre-reversal, the post-registration roller sensor does not detect
the original after it has been moved a specific distance (50 mm) following
the activation of the reversal motor.
At time of pre-reversal, the reversal sensor does not detect the original
after it has been moved a specific distance (100 mm) after the post-
registration roller sensor has gone on.
At time of pre-reversal, the reversal sensor does not detect the original
when it has been moved over a specific distance (100 mm) after the
reversal motor has stopped.
S1,S4 At time of reversal, the separation sensor has detected the original when
it has been moved over a specific distance (169 mm) after the reversal
sensor has gone on.
S2,S4 At time of pre-reversal, the pre-registration sensor has detected the
original when it has been moved over a specific distance (120 mm) after
its trail edge has moved past the separation pull-off roller.
S2,S3 At time of pre-reversal, the post-registration roller sensor detects the
original after it has been moved a specific distance (50 mm) following the
passage of the trail edge of the original for the pre-registration roller
sensor.
S1,S3 At time of pre-reversal, the reversal sensor detects the original after it has
been moved a specific distance (100 mm) following the passage of the
trail edge of the original from the pre-registration roller sensor.
S1 At time of pre-reversal pickup, the reversal sensor does not detect the
original after it has been moved a specific distance (100 mm) following
the start of the reversal sensor.
S1,PI4 At time of pre-reveal, the pre-reversal sensor has detected the original
when it has been moved over a specific distance after the reversal sensor
has detected its lead edge.
S1,PI4 At time of pre-reversal pickup, the reversal sensor detects the original
after it has been moved a specific distance following the detection of its
trail edge by the pre-reversal sensor.
S2 At time of reversal, the pre-registration roller sensor does not detect the
original after it has been moved a specific distance (197 mm) following
the end of arching operation.
S2 At time of reversal, the pre-registration roller sensor detects the original
after it has been moved a specific distance (original length X 1.5 mm)
following the start of the pre-registration roller sensor.
S4,S5 At time of separation, there is a discrepancy of an equivalent of 10 mm in
the timing of detecting the lead edge between the separation sensor and
the skew sensor.
S4,S5 At time of pickup, there is a discrepancy of an equivalent of 10 mm in the
timing of detecting the trail edge between the separation sensor and the
skew sensor.
S1 At time of pickup, the reversal sensor detects an original before it moves
past the pre-registration roller sensor.
Chapter 16
16-19