Canon imageRUNNER 7095 Service Manual page 455

Code Sensor type
0057 1st sheet pre-
reversal pickup
delay
0058 1st sheet pre-
reversal pickup
stationary 1
0059 1st sheet pre-
reversal pickup
stationary 2
0060 1st sheet reversal
pickup delay
0061 1st sheet reversal
pickup stationary
0062 1st sheet pickup
lead edge skew
0063 1st sheet pickup trail
edge skew
0064 1st sheet pickup
fault 1
0065 1st sheet pickup
fault 2
0066 1st sheet reversal
pickup trail edge
skew
0067 1st sheet reversal
pickup NG1
0071 timing fault 1
0072 timing fault 2
0073 illegal size
0074 manual feed original
size error
0075 image lead edge
position error
0076 1st sheet image lead
edge position error
0077 belt speed setting
error
0078 belt speed switch-
over error
0079 belt status error
0080 image lead edge
output timing error
0081 reversal speed
setting error
0082 reversal speed
switch-over error
0083 reversal status error PI5
0084 last original error
Sensor No. Description
S1 The 1st sheet is identified as a pre-reversal pickup delay jam (0017).
S1,PI4 The 1st sheet is identified as a pre-reversal pickup stationary 1 jam
(0018).
S1,PI4 The 1st sheet is identified as a pre-reversal pickup stationary 2 jam
(0019).
S2 The 1st sheet is identified as a reversal pickup delay (0020).
S2 The 1st sheet is identified as a reversal pickup stationary jam (0021).
S4,S5 The 1st sheet is identified as a pickup lead edge skew jam (0022).
S4,S5 The 1st sheet is identified as a pickup trail edge skew jam (0023).
S1 A pickup NG1 condition (0024) has occurred on the 1st sheet.
S3,S2 A pickup NG1 condition (0025) has occurred on the 1st sheet.
S4,S5 A reversal pickup trail edge skew condition (0026) has occurred on the
1st sheet.
PI4 The 1st sheet is identified as a reversal pickup fault 1 jam (0027).
- The software control mechanism has failed.
- In copyboard mode, an original has been read and moved to and stopped
at the right side of the platen roller; however, the preceding original has
not been delayed.
S3 At time of LDR stream reading, the post-registration sensor detects the
original after it has been moved a specific distance (30 mm) from the wait
position.
S9,S1 At time of manual feed, the reversal sensor detects an original while the
manual registration roller sensor also detects an original.
S7 At time of stream reading, no change has occurred in the read position in
response to a request for a change.
S7 The 1st sheet is identified as having an image lead edge position error
(0075).
PI1 The speed setting of the belt motor is below the minimum speed (100
mm/sec) or above the maximum speed (700 mm/sec).
PI1 When the belt motor speed is switched over, the belt motor is not moving
at a constant speed.
PI1 At time of switch-over, the state is not any of the following: acceleration,
constant speed rotation, deceleration.
S2,S3,SW3 At time of stream reading, the image lead edge signal is generated in the
01 course of acceleration while a move is made from the wait position to the
image lead edge position.
PI5 The speed setting of the reversal motor is below the minimum speed (100
mm/sec) or above the maximum speed (700 mm/sec).
PI5 At time of switching over the reversal motor speed, the reversal motor is
not rotating at a constant speed.
At time of switch-over, the state of the reversal motor is not any of the
following: acceleration, constant speed, deceleration.
PI1 A belt motor error occurs while the last original is being discharged by
the platen roller or being moved.
Chapter 16
16-21