Mitsubishi Heavy Industries SRK25GZ-L1 Handbook page 371

Model FDT308CES-A
Item
(1)
Nominal cooling capacity ISO-T1
ISO-T3
Power source
Cooling input
Running current (Cooling)
Power factor (Cooling)
Cooling input
Running current (Cooling)
Power factor (Cooling)
Inrush current (L.R.A)
Noise level (4)
Exterior dimensions
Height × Width × Depth
Net weight
Refrigerant equipment
Compressor type & Q'ty
Motor
Starting method
Heat exchanger
Refrigerant control
Refrigerant
Quantity
Refrigerant oil
High pressure control
Air handling equipment
Fan type & Q'ty
Motor
Starting method
Air flow (Standard)
Fresh air intake
Air filter, Q'ty
Shock & vibration absorber
Electric heater
Operation control
Operation switch
Room temperature control
Safety equipment
Installation data
Refrigerant piping size
Connecting method
Drain hose
Insulation for piping
Accessories
Optional parts
Notes (1) The data are measured at the following conditions.
Item
Operation
Cooling
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616 "UNITARY AIR-CONDITIONERS"
(3) The operation data indicate when the air-conditioner is operated at 380/415V 50Hz and 380V 60Hz respectively.
(4) Indicates the value at mild mode.
Model
FDT308-A
W
3 Phase, 380-415V 50Hz or 380V 50Hz/415V 50Hz, 380V 60Hz
kW
A
%
kW
A
%
A
dB(A) Hi:41 Lo:35
Unit 260 × 840 × 840
mm
Panel 30 × 950 × 950
kg 30 (Unit:24 Panel:6)
–
kW –
–
Louver fins & inner grooved tubing
–
kg Holding charged
r
–
Turbo fan × 1
30 × 1
W
Line starting
CMM Hi:17 Lo:12
Available
Long life filter × 1 (washable)
Rubber sleeve (for fan motor)
W –
Wired remote control switch
(Optional:RCD-C-S-E)
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat.
mm
Liquid line: φ9.52 (3/8") Gas line: φ15.88 (5/8")
(in)
(Connectable with VP25)
Indoor air temperature
DB WB
27˚C 19˚C
29˚C 19˚C
FDT308CES-A
FDC306CES3
7100/7700
5700/6000
2.83/2.84/3.35
5.3/5.3/6.0
81/75/85
3.02/3.03/3.58
5.7/5.7/6.5
80/74/84
43
844 × 950 × 340
RC5538ESE1 × 1
Line starting
Slitted fines & bare tubing
Capillary tube
R22
1.3 [Pre-charged up to the piping length of 5m]
1.63 (SUNISO 3GS)
High pressure regulator valve
Propeller fan × 1
Line starting
Rubber mount (for compressor)
- (Indoor unit side)
Internal protector for compressor.
Internal thermostat for fan motor.
Internal Pressure relief valve for compressor.
Flare piping
Necessary (both Liquid & Gas lines)
Mounting kit.
Decorative Panel
Outdoor air temperature
DB WB
35˚C 24˚C
46˚C 24˚C
FDT ( N ) -C
59
67
2.24
60 × 1
54/56
–
–
–
–
–
Standards
ISO-T1, JIS B8616
ISO-T3, SASO
369